• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Dana 44 knuckle removal help

JohnJohn

Contributor
Bronco Guru
Joined
May 6, 2005
Messages
2,179
Loc.
Richmond
Guys,
Can some one help me understand the process to get the knuckles and Axel shafts off of a front Dana 44?

I picked up an older Dana 44 with drums and need to swap knuckles with my 77 disk Dana 44. I also want to swap axel shafts because the u joints look better on my 77 diff.

I know the Drums are stuck on the hubs on both sides of this diff but I wanted to get the correct steps before I start attacking the drums.

Can I pull the knuckle off without hammering on the drums for days?

Also can anyone tell me what size wrench I need for the smaller ball joint nut that is on the inside of the knuckle?

Thanks,
John
 

ugly74

Bronco abuser
Joined
Apr 17, 2006
Messages
2,856
Loc.
Colorado
after you get down to the bare knuckle (no brakes, bearings, tie rods,or spindle left)
and after removing the nuts on the balljoints (leave one attached, but backed off most of the way)
you're going to need a "pickle fork" or ball joint seperator. it's basically just a two pronged wedge that gets driven in between the knuckle and axle end.

I know at Checker Auto parts, they can be rented. lay down a deposit, use the tool, bring it back and get the full deposit back. so it's free.

there's a smaller version for use on the tie rod ends too.
 
OP
OP
JohnJohn

JohnJohn

Contributor
Bronco Guru
Joined
May 6, 2005
Messages
2,179
Loc.
Richmond
So far I removed the hub lock switch and the locking ring at the end of the axel shaft.
I also took one of the ball joint nuts off but I need to buy a larger open end wrench to get the inside ball joint nut off.

I have a pickle fork to separate the ball joints.

anyone have a picture of a spanner wrench? I don't think I have one.
 

NicksTrix

Bronco Guru
Joined
Aug 1, 2001
Messages
6,410
spanner wrench is another name for an adjustable wrench, cresent wrench what ever you want to call it. if you don't have a socket or wrench to fit the large nut.
think it's 1 5/16.
 
OP
OP
JohnJohn

JohnJohn

Contributor
Bronco Guru
Joined
May 6, 2005
Messages
2,179
Loc.
Richmond
I was able to use an adjustable crescent wrench/spanner wrench to get the lower ball joint nut off but the top ball joint has a smaller nut that is on the inside of the knuckle.

I need to go out and buy a large open end wrench. My crescent wrench or a socket will not fit in the tight space.

I tried a 1 1/16 wrench but it is a hair larger that this. Guess it is 1 3/8.
 

bronko69er

EB Addict
Joined
Oct 16, 2006
Messages
4,599
Loc.
Renton, WA
I was able to use an adjustable crescent wrench/spanner wrench to get the lower ball joint nut off but the top ball joint has a smaller nut that is on the inside of the knuckle.

HUH??:? On a dana44? You must be looking at it upside down. The 2 nut sizes IIRC are 1-1/8" and 1-5/16".
 
Last edited:

bronko69er

EB Addict
Joined
Oct 16, 2006
Messages
4,599
Loc.
Renton, WA
Just so we got things straight, here's what you have to do.
Remove calipers (if this is the axle in question)
Remove the locking hubs,
Remove the spindle nuts (special socket)
Reomve hub/drum or disc,
Remove spindle and packing plate or caliper bracket,
Remove tie rod ends from knuckle (pickle fork),
Remove axles,
Remove ball jount nuts (1-1/8" and 1-5/16"),
Wack the knuckle with a BFH and it should pop off. (or use a pickle fork)

Here are some pics that might help
http://broncograveyard.com/dia/6/d44diaaxle.jpg
http://broncograveyard.com/dia/6/d44diadisc.jpg
http://broncograveyard.com/dia/6/d30dialockout.jpg
 

Flash69

Bronco Guru
Joined
Jul 21, 2004
Messages
2,429
Loc.
Southwest Va
I was able to use an adjustable crescent wrench/spanner wrench to get the lower ball joint nut off but the top ball joint has a smaller nut that is on the inside of the knuckle.

I need to go out and buy a large open end wrench. My crescent wrench or a socket will not fit in the tight space.

I tried a 1 1/16 wrench but it is a hair larger that this. Guess it is 1 3/8.

That smaller nut you are talking about thats inside the knuckle is for setting the preload on the balljoint when it is being installed. It is called a threaded balljoint bushing. You dont have to take that out to get the knuckle off. Just take the upper and lower bolts off and whack it with a hammer. Dont beat on the threads if youre reusing the balljoints. You can get the other out easy after it comes apart. A spanner wrench or socket as most call it is whats used to set the preload or to take it out after the knuckle comes out. Jeffs Bronco Graveyard has the socket for $12.00 Part# 12204ss. I got mine from snapon for 25 bucks. Go to Jeffs site and type in that part # and you will see the tool.
 
OP
OP
JohnJohn

JohnJohn

Contributor
Bronco Guru
Joined
May 6, 2005
Messages
2,179
Loc.
Richmond
You guys rock. Thank you for the info. I am sure I will get it tonight but I do need to pick up some larger wrenches. I guess 1 and 1/8 is the size.

My F250 super duty and the Bronco require much larger tools that I have been able to get away with for years.
 

bronko69er

EB Addict
Joined
Oct 16, 2006
Messages
4,599
Loc.
Renton, WA
I was able to make my own spanner socket for the ball join sleeve from a $.50 3/4" deep socket form the pawn shop and a dremel. It's not too hard if you are handy with a ginder/dremel.
 

Jungleboy

New Member
Joined
May 14, 2006
Messages
37
Loc.
Clear Lake / Houston
I just did ball joints (Moog) on a full width D44 out of a 76 Ford F-150. If you are planning on torquing everything to specs you may consider buying or renting the proper size sockets. The lower ball joint was torqued to 70 ft#s. The threaded insert on the upper ball joint was also torqued to 70 ft#s. The nut for the upper was torqued to 100 ft#s. I spent half a day driving around town checking every auto parts chain known to man looking for the socket for the threaded insert (no luck). Ordered one-on line and got it the following day. I also stopped by a 4x4 specialty shop, which I will leave un-named to protect the guilty, and the guy told me they used a BFH/BFS combo to get the job done. So, if your going with the "calibrated elbow" method, an adjustable wrench should be fine. I'm working a frame up restoration and don't want to leave chance. To many "death wobble" threads out there. Good luck!!!
 

bronko69er

EB Addict
Joined
Oct 16, 2006
Messages
4,599
Loc.
Renton, WA
The threaded insert on the upper ball joint was also torqued to 70 ft#s.

Did you check the "pull force" at the tie rod hole on the knuckle?
It' supposed to be at about 25lb IIRC. Mine hit 25lbs at about 40ft-lb of preload on the threaded sleeve. Just concerned that 70ft-lb might be too much causing extra unnecessary stress on your steering components.

JohnJohn,
This is a ball joint ajduster socket you'll need for the re-install.
http://www.napaonline.com/MasterPag...&Description=Ball+Joint+Sleeve+Spanner+Wrench
And a spindle nut socket.
http://www.napaonline.com/MasterPag...mber=2467&Description=Spindle+Lock+Nut+Socket
 

Flash69

Bronco Guru
Joined
Jul 21, 2004
Messages
2,429
Loc.
Southwest Va
Did you check the "pull force" at the tie rod hole on the knuckle?
It' supposed to be at about 25lb IIRC. Mine hit 25lbs at about 40ft-lb of preload on the threaded sleeve. Just concerned that 70ft-lb might be too much causing extra unnecessary stress on your steering components.

JohnJohn,
This is a ball joint ajduster socket you'll need for the re-install.
http://www.napaonline.com/MasterPag...&Description=Ball+Joint+Sleeve+Spanner+Wrench

When i did mine i called Chuck at BC Broncos. He told me that it was 40ft lbs on the preload. Right you are.
 
OP
OP
JohnJohn

JohnJohn

Contributor
Bronco Guru
Joined
May 6, 2005
Messages
2,179
Loc.
Richmond
Thanks for all the help guys. There was so much crud and rust on the knuckle that it was hiding the seam where the shaft comes out of the knuckle. I looked at another 44 I have and all made since.

The big problem I have now is the drums are not coming off. I hit it with a butane torch and a 5 pound sledge with no luck. I am not reusing the knuckles so I may just cut the ball joints and pull the Axel shaft out.

I have another 77 Dana 44 that has disk breaks and am planning on using the shafts and knuckles on this one.

I am doing this to change over from a 3.50 to a 4.10. The 9" was much easier that a rusted diff with knuckles.
 

Flash69

Bronco Guru
Joined
Jul 21, 2004
Messages
2,429
Loc.
Southwest Va
Remove the Hub and drum all together. It makes it a lot easier. You will have to destroy the drum if you dont.
 
Last edited:

bronko69er

EB Addict
Joined
Oct 16, 2006
Messages
4,599
Loc.
Renton, WA
A little more detailed list for you:
Remove 6 bolts that hold on locking switch,
Remove switch,
Remove both snap rings (one on OD of axle shaft, one on ID of hub)
Remove locking hub internals
Remove outer spindle nut,
Remove locking ring/washer
Remove inner spindle nut,
Drum and hub shouild come right off,
If not loosen the brake shoe adjuster and/or open the bleeder screw.
That should do the trick.
 
OP
OP
JohnJohn

JohnJohn

Contributor
Bronco Guru
Joined
May 6, 2005
Messages
2,179
Loc.
Richmond
With your advise I have made progress but I am stuck again.

I picked up a spanner nut and puled everything off the knuckle except for the spindle. It is seized to the knuckle.

Are there any tips or tricks to get the spindle off of the knuckle?

I have saturated it with PB Blast and tried heating it but is there a method to use a puller to get it out or a spot where I can hit it with a hammer?

If I cant get the spindle out my only visible option is to cut the ball joints and pull the knuckle and shafts out.
Thanks,
John
 
Top