• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

larger rear wheel cylinders

Bronchole

Bronco Guru
Joined
Mar 24, 2004
Messages
1,611
Loc.
Chatsworth, Ca (LA)
I need a bit more braking power out of my rear brakes to ballance my brake system. I am running the 11" rear drums and do not want the expense of converting to the 10" or disk. The current rear wheel cylinders are 13/16" diameter. I started looking at NAPA for larger diameter wheel cylinders and instantly noticed that the stock front drum brake wheel cylinders are 1 1/8". Has anyone tried to bolt these up in the rear? Is there any issue with the lines running to them?

Dan
 

Apogee

Contributor
Bronco Guru
Joined
Nov 26, 2005
Messages
6,348
Loc.
Tangent, OR
You can get 15/16" bore wheel cylinders from the F150 trucks (1977 for sure)...the 1-1/8" wheel cylinders are more than double the area of your 13/16" ones, 1.227 square inches versus .518. i don't think doubling your rear brake actuation force would be wise. A 15/16" bore wheel cylinder works out to be .69 square inches, or about a 33% increase in area.

IIRC, I've read about others doing this as well, so I'd be interested to hear how it works out for you, whichever way you choose to go.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
I'm not sure you would actually gain braking power by swapping the rear cylinders for larger ones because now you will need more fluid volume to move the larger cylinders so you would probably get less force out of them than the smaller ones. The larger front cylinders also have more fluid pushed to them by the MC. A better choice may be to swap MC's to increase braking power. Do you currently have front Discs already? if not swap to them first. The rear brakes only account for about 30% of the braking action anymore than that and you'll lock up the rears and create a dagerous condition.
I'm usually not one to suggest H boost but with 35in tires it may be your best bet.
 
OP
OP
Bronchole

Bronchole

Bronco Guru
Joined
Mar 24, 2004
Messages
1,611
Loc.
Chatsworth, Ca (LA)
Hydroboost with1 1/4" M/C, T-bird front calipers which are larger in diameter than the F150 calipers and made a huge difference in front braking power, maybe even more of a difference than the hydroboost.

As it stands right now I have no problem locking the front brakes up but under no condition other than in dirt can I lock up the rear brakes. This was true even with a 100% rebuild of the rear brakes (new drums, new pads, new wheel cylinders, new spring kit, new adjusters, new hard lines, new flex line). Brake effort (how hard I need to press the brake pedal) is relitivly low to cause the front wheels to lock up but allot of additional effort doesn't get the rears to lock up.

Since I am running the largest M/C available that tells me that the easiest way to ballance this out is to improve the rear brakes. Given X ammount of PSI supplied from the M/C with sufficent volume, a larger wheel cylinder should do the trick.
 
OP
OP
Bronchole

Bronchole

Bronco Guru
Joined
Mar 24, 2004
Messages
1,611
Loc.
Chatsworth, Ca (LA)
You can get 15/16" bore wheel cylinders from the F150 trucks (1977 for sure)...the 1-1/8" wheel cylinders are more than double the area of your 13/16" ones, 1.227 square inches versus .518. i don't think doubling your rear brake actuation force would be wise. A 15/16" bore wheel cylinder works out to be .69 square inches, or about a 33% increase in area.

IIRC, I've read about others doing this as well, so I'd be interested to hear how it works out for you, whichever way you choose to go.


Thanks for the 15/16 info, that makes sense and is the approximate direction I started looking towards. I just saw the front Bronco ones first, cussed that I had thrown away the possible ones I was looking for and started this thread.

Dan
 

Apogee

Contributor
Bronco Guru
Joined
Nov 26, 2005
Messages
6,348
Loc.
Tangent, OR
When I posted before, I didn't realize that the 1976 and 1977 EB's came with 15/16 rear wheel cylinders as well...basically when they went to discs as standard in the front. This must help balance out the system considering the added stopping power up front. Considering I've got a 77 EB and a 77 F150, I should've known better.

Personally, I don't agree the "theory" that being able to lock up your brakes with little effort implies they are good brakes. A lot of brake torque and good brakes are two totally different things IMO. I think balance and the ability to modulate and threshold brake are much more important than brake torque alone and for that reason will not likely ever run the T-bird calipers up front. Ultimately you're limited to where the rubber meets the road and anything beyond that is excessive IMHO.

If you look at most performance brake kits, the piston area is reduced for improved pedal feel and modulation, pad area/volume is increase, and rotor mass and diameter are increased.
 
OP
OP
Bronchole

Bronchole

Bronco Guru
Joined
Mar 24, 2004
Messages
1,611
Loc.
Chatsworth, Ca (LA)
When I posted before, I didn't realize that the 1976 and 1977 EB's came with 15/16 rear wheel cylinders as well...basically when they went to discs as standard in the front. This must help balance out the system considering the added stopping power up front. Considering I've got a 77 EB and a 77 F150, I should've known better.

Personally, I don't agree the "theory" that being able to lock up your brakes with little effort implies they are good brakes. A lot of brake torque and good brakes are two totally different things IMO. I think balance and the ability to modulate and threshold brake are much more important than brake torque alone and for that reason will not likely ever run the T-bird calipers up front. Ultimately you're limited to where the rubber meets the road and anything beyond that is excessive IMHO.

If you look at most performance brake kits, the piston area is reduced for improved pedal feel and modulation, pad area/volume is increase, and rotor mass and diameter are increased.


The statement that I am able to lock the front brakes up is as apposed to them not locking up with the previous calipers so being able to lock up in the first place is of primary concern, then modulating..... My system allows for easy modulation of the front brakes, just no ability to lock the rear brakes what so ever. I would think that a good brake system would allow for simotanious lockup of the front and rear brakes in 90% of situations with reasonalbe (not excessive) pedal effort and allow for good "road feel" and ability to modulate the brake system allowing the driver to maximize (just shy of lockup) the braking in a panic situation.

At least that is what I am aiming for.

The 76/77 Broncos had the smaller diameter yet wider rear drum brakes didn't they? Just some more variables to add in to the equasion if I were to attempt to copy an existing brake system.

I am really looking at the "throw it in there and see what it does" type of thing because as far as I can tell there are no vehicles that have the hydroboost, 1 1/4 M/C, t-bird front calipers, 35" tires, similar wheelbase and COG, simmilar suspension and 11" x 1 3/4" rear drums that I can just simply look at what diameter rear wheel cylinders they are running and go that way.

Dan
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Ditto the larger brakes on 76/77.
Have you tried a MC with a smaller bore than 1 1/4? If you go smaller 1 1/8" you should actually have more pressure which may help the rear brakes and may help keep the front brakes from locking up as quickly to balance it out more. You can go either way MC or wheel cylinder but I would think MC would ber a way quicker way to go and since you already have H boost a slightly stiffer pedal wont be noticed.
 
Top