• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

when to replace timing chain?

rjrobin2002

Contributor
Bronco Guru
Joined
Oct 13, 2007
Messages
2,951
To stay true to your passion, get rid of the small block and put a 428 in it.
 
OP
OP
Susan76

Susan76

New Member
Joined
Jun 20, 2013
Messages
30
Thanks

Broncnaz -- ya Folgers was good for them late 60s before Moroso did their insulated cans... don't know why I never took it off all these yrs... I built that one for my first Drag Pack car maybe Oct 1968... later ones ran the lines through the sides.

rjrobin2002 -- FE in EB -- I've thought about it... that 390 6V -- the looks when you open the hood... but I don't think it would be practical. 390 6V into my Ranchero and the 351W into the Bronco.... I haven't even tried the 302 where I want to use it. It may be fine and the longer stroke may not be needed.
 

stock1970

Bronco Guru
Joined
Apr 2, 2008
Messages
1,793
Loc.
Olathe, Kansas
replace the timing gear and chain anyways.. I have had two fail me at highway speed taking out all the valves in the process.. my mustang 2 had the synthetic gears and they failed at around 100k miles. my 76 bronco gears let chain slip and took out the valves at around 110k miles..
 
OP
OP
Susan76

Susan76

New Member
Joined
Jun 20, 2013
Messages
30
She DIDN"T fail me!

Guys I let that OLD 735 soak over night -- its been just short of 3 years since I last fired up the 428 it belongs to, Hit it with the elec pump and it didn't flood so.... pulled the bowl sight plug & fuel was where it is suppose to be... accel pump seemed to be weeping some so I changed my steering damper -- ya just to give it time....

pumped acc pump a couple of times and after 30 sec cranking it fired -- not good though.. ran BUT and I couldn't get dwell reading on the dist. So it died and would not restart.....

Friend gave me another small block point dist Monday so I dropped it in.... checked the points at 17, eyeball the #1... crank 30 sec and fires up. then I play with it a little -- end result with the 45 yr old 735 (idle air bleeds adj makes NO change) I can get it to sit and idle at 425 rpm @10* advance AND even put it in to gear without it dying. Have to bump the idle to 500 rpm to get to start by just touching it.... AND there is NO timing jump at all. Holds absolutely steady at the 10* adv position... it apparently was the XXXXXXXXXing AutoZome reman distributer causing all the problems.

So time to switch back to the Holley 470 so I can hook up everything. I would have loved to just try the 735 on the street BUT... I have a kit coming for a different 735 - one for an automatic & I can tap into the intake for the power brake so I may try it just for grins...

I really want to thank you all for your time and suggestions. I'll let you know how the 470 works.
Susan
 

Attachments

  • 018c.jpg
    018c.jpg
    110.8 KB · Views: 115
  • 017c.jpg
    017c.jpg
    91.3 KB · Views: 104
  • 016c.jpg
    016c.jpg
    91.2 KB · Views: 75
  • 014c.jpg
    014c.jpg
    89.9 KB · Views: 53

baddad457

Sr. Member
Joined
Aug 24, 2011
Messages
560
Broncnaz -- ya Folgers was good for them late 60s before Moroso did their insulated cans... don't know why I never took it off all these yrs... I built that one for my first Drag Pack car maybe Oct 1968... later ones ran the lines through the sides.

rjrobin2002 -- FE in EB -- I've thought about it... that 390 6V -- the looks when you open the hood... but I don't think it would be practical. 390 6V into my Ranchero and the 351W into the Bronco.... I haven't even tried the 302 where I want to use it. It may be fine and the longer stroke may not be needed.

;D What's impractical about a daily driver 3 x 2 ? I've got one topping a 331 ;D I used to have it in an 89 Ranger backed by a Toploader 4 speed, now it's in a 77 Comet.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Sometimes remanned isnt always remanned right. Glad you found your issue. Although it could also have been the points or even the condensor in that remanned dizzy.
You probably didnt miss much not being able to try out the 735 on the street. It most likely wouldnt have been to responsive on a stock mid 70's 302 in a heavy vehicle. When I swap from a 600 to a 525 its noticeable. the 525 responds better than the 600.
 

cldonley

Contributor
Bronco Guru
Joined
Jul 4, 2011
Messages
1,398
Loc.
Robinson, TX
;D What's impractical about a daily driver 3 x 2 ? I've got one topping a 331 ;D I used to have it in an 89 Ranger backed by a Toploader 4 speed, now it's in a 77 Comet.

That must be a blast. I had a 73 Comet (my second car) with an early 302 and a C3. That dude was serious fun;)

Welcome aboard Susan. Sounds like we may be calling on you for some tips!
 
OP
OP
Susan76

Susan76

New Member
Joined
Jun 20, 2013
Messages
30
470 hi idle

Put the 470 back on and everything hooked up -- 15 sec crank and ran. Went through adj just make sure they were reasonable. Steady 17" vac off the frt combined primary draw port. no "smoke" with the PCV hooked up so the draw is working - there was just a hint coming out with the 735.. timing 10* "idle" 41* @ 2100 rpm with vac line connected. 25* dwell.. AND the timing mark is steady all the way through the range.

BUT with the idle adjustment screw all the way out its at about 900 rpm.... doesn't diesel when I turn it off & will start back up in what seems like 1 sec. I checked the secondary for being closed against the stop. Guess I'll have to take it off and back off on the secondary idle setting. I'll drive tomorrow afternoon and see how it is on the street.

Side bar - had an awful time not putting a battery in the 428 and firing it up.. maybe tomorrow night or this weekend.... I haven't changed the plugs in 35 yrs... pulled and looked at them and put them back in. TG for never seize.. this carb got me a bit fired up to maybe pulling the frt springs and installing the roller mounts and 5* GW upper control arms.... and and and...

2nd side bar - I have the Drake "Bronco powered by Ford" valve covers -- they leaked like crazy with the really good (expensive) FelPro gaskets - put on a set of cheap cork --- NO leaks.


Badad457 -- its the 390FE weight over the small block.. not sure about the 6V off roading... street no problem that's why it will probably end up in my 69 Ranchero GT. -- then that 351W in the Bronco.
 

baddad457

Sr. Member
Joined
Aug 24, 2011
Messages
560
That must be a blast. I had a 73 Comet (my second car) with an early 302 and a C3. That dude was serious fun;)

Welcome aboard Susan. Sounds like we may be calling on you for some tips!

It's been a blast. These cars are so light in the rear. It's had a C4 up until last month, now it's got the Toploader saved and rebuilt from the ranger. It goes sideways in 1st and 2nd without a thought with the 3.50 geared Trac-loc 9" and 295/50's. Currently down though to fab a firewall plate to stiffen it more for the hydro clutch setup.
 

baddad457

Sr. Member
Joined
Aug 24, 2011
Messages
560
Badad457 -- its the 390FE weight over the small block.. not sure about the 6V off roading... street no problem that's why it will probably end up in my 69 Ranchero GT. -- then that 351W in the Bronco.

Yea, they do tend to choke up with sudden deceleration, so they'd not be my choice for extreme off road. But otherwise they're very reliable for street driving. I bought my setup about ten years ago secondhand (they were a year old then) Ain't even touched em since other than one jetting change after adding spacers under them, And the sound with a quiet exhaust !!! Stereo !!
 
OP
OP
Susan76

Susan76

New Member
Joined
Jun 20, 2013
Messages
30
just not sure

Well took it for a ride around town. Went to a few places so there was a number of shut off and start up 5 - 10 min later. Ran great. Shuts right off- starts in half a crank, idles in traffic, good brakes.... idle vac 18" coolant temp 180* 40# oil 13v no problem as far as the high idle at stop signs or lights etc easy 45+ minutes driving

Then I headed out of town.... 45 mph zone did about 4 kick downs into 2nd gear just getting a feel for it... maybe up to 60.. cruise at little over 50 (per GPS) for mile or so and suddenly it bucks.... I slow down do a 180 and head back into town. Have to feather the throttle for a mile+ to keep it running at about 38 mph. Did not think I was going to make it back. Hit the elec fuel pump (hey got nothing to lose) override switch for about 10 sec and it smooths right out. Runs fine... got back home and its fine put some cooling system cleaner in and it ran for 45 minutes like nothing could be wrong. Shut off to dump the coolant and then tried to start again - no problem... so i've been letting it cool down so I can add more water and run the flush again.

Elec pump has a 5# oil safety switch with the override that I pushed.. so a tell tale light on the switch to be sure its working??? bypass stock mechanical pump..by pass the elec pump... go buy fuel pressure gauge to mount on the hood.... keep it for running around town and forget taking out to the desert.... http://classicbroncos.com/forums/imagesCB/smilies/sad.gif
 

WheelHorse

Bronco Guru
Joined
Nov 22, 2004
Messages
2,511
Susan, you don't think you're picking up stuff from the tank do you? Old desert dust that gets stirred up when you hammer down, get's picked up and the additional override compensates?

ISTJ here...just the facts mam. LOL
 
OP
OP
Susan76

Susan76

New Member
Joined
Jun 20, 2013
Messages
30
crap in gas tank

Wheelhorse

New 23 gal from TBC .. rinsed (not easy for me to do so maybe I didn't get it all out)..... before installing last Sept but never put gas into it until 2 weeks ago -- even bought a new gas jug just for the new gas -- 2x - 5 gal and then the station for 10 gallons.

I wasn't happy with the design as the pickup is at the front of the tank... wish now I had paid the extra for WH tank. BUT no one shows HOW their tank is set up inside -- I thought it would have been baffled and centre pick up. I had it too long to send back before I even opened the box.. blind trust in "Bronco speciality dealer"....

Last night rechecked dwell - timing - rpm - vac - temp --- all ok

I went under it this AM. So your answer is YES - filter (second one) I put on just off the tank outlet has more crap in it. Front filter at the carb still looks clean. now wondering how to get all of the crap (looks like white flakes) into this filter and not having to keep changing them. As it happened shortly after kicking down into 2nd 4x seems it may be that there was "stuff" hung up in the back of the tank. So I am thinking that its running good that I'll go fill the tank to 3/4 (only had it to just over 1/2) and runaround some more trying to splash gas around - I'll carry a couple of filters, screwdriver and tarp to lay on so if it totally fails I can change it beside the road... Its just behind the rear diff so its easy to get to.... how I wish I was 35 and doing this - wouldn't be a big deal.. oh well at least I woke up this AM....

AND I am going to start a new question thread on steering boxes if I can't find some answers about mine....

like that "Just the facts"...
 
OP
OP
Susan76

Susan76

New Member
Joined
Jun 20, 2013
Messages
30
runs nice

Not babying it but not hard. Took it to dinner then Sonic for some desert and then a 15 mile country road ride..... not one skip that I noticed. Brought fuel up to 3/4 so we'll see, Tomorrow I'll throw a couple of filters, screwdriver and tarp and head out on some backroads.

Thanks guys for your help and suggestions.
Susan
 
OP
OP
Susan76

Susan76

New Member
Joined
Jun 20, 2013
Messages
30
runs fine - but temp

Last night, 3/4 tank again not babying it so its sloshed fuel round the tank and went about 40+ miles. Speeds by GPS. Short interstate 65 mph 3-4 miles, 6 miles around town after I got gas before getting on the interstate then headed towards the border. 15 miles out 55 -60 mph and temp starts to rise - factory gauge. aux elc fan on override does not seem to help. 50 mph 12" vacuum 60 11" vacuum so I turned around and started back. Heating didn't seem to start until sustained 60 mph. Our interstates are all 75 & state roads 65 here so a little concern with traveling. Engine ran good.. haven't looked at the rear fuel filter yet today.

Temp started dropping when I took a side road at about 45-50 mph. Looks like I should install a mechanical gauge to be sure - where to put another one?? I had the rad cleaned when it was out & flow that I can see looks good once the stat opens. I flushed the cooling system 3 times & last one only clear water came out. Still have not hooked up my new heater core. MAYBE bypassing it is raising the temp as hot coolant is circulating back to the water pump. Also I might be able to pull a little more air if I put a fan spacer on and move it into the shroud an inch or so. BUT not sure of body to engine flex which is why the fan is where it is.

Now to fill the tank... it dawned on me that I don't remember ever cleaning the new rubber fill pipe to tank hose so I wonder if there was some coating inside it that came off when I poured gas in. Also I need to read the plugs. One time when I wish I had O2 sensors available... or portable so I could plug in the tailpipes and go for a run....
 

Attachments

  • long road 003.JPG
    long road 003.JPG
    170 KB · Views: 67
  • free ride 01.jpg
    free ride 01.jpg
    70.5 KB · Views: 95

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Definetly a good idea to check your jetting. How hot was it getting? Might just put in a mechanical guage temporary just to do a check.
Broncos had about a 3/4" fan spacer stock. As long as the fan blades are about 1/2 in the shroud it should be fine. Dont want the fan to close to the radiator as you mentioned about flex. If you have at least 1in you should be fine.
I dont think not having a heater core would cause your issue. but of course if you have a hose connected from the manifold to the waterpump then yeah you may have to much coolent bypassing the radiator with both that hose and the stock bypass hose hooked up.
Sometimes aux fans create more issues than they solve. They tend to block airflow. especailly at hiway speeds.
 
OP
OP
Susan76

Susan76

New Member
Joined
Jun 20, 2013
Messages
30
no fan spacer

There isn't any fan spacer so I'll have to look. All the ones I have stacked together seem to be 2"+ -- problem of 60s bodies --big spaces in front of the engines. Hard to tell from the factory gauge - I was going to look closely at it today but got hung up on another project -- trailer lights wiring and now wheel bearings.......

I have never run an aux fan. It just seemed like a god idea out here in the SW. Never had to deal with 75-80 being the LOW temp of the day... I could vice grip the "heater bypass line" as a test... or just hook it up now that I am 90% sure I have the system clean.

In looking at alternative guages there is a set I of 5 would like but I need another SW pod to match mine. These 4 are from the 70's and I haven't found more. I could hang one more off the right side. Otherwise????? and the 2 mounting holes in this new dash top..... And I don't know why that photo makes them look like they are going down hill. The other alternative that I haven't found yet is a cage mount pod that could go on the driver's upright. The one custom speedo - gauge unit that I would pay for is a HUD. --

I don't mind running dual gauges as the originals are old and semi hard to read in the dash unit. These new gauges have a temp sensor mount for coolant that goes into the radiator hose. Like to find one to go into the trans cooler line.
 

Attachments

  • 012c.jpg
    012c.jpg
    85.8 KB · Views: 117

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Yeah the bronco spacer is smaller I think they were used on other vehicles to but Im not sure what ones. But here' a pic. Id have to look around I may have a stock spacer somewhere.

Up to you on the gauges. Id just do a verification and if all checks out pull the mechanical one back out. Although there having a mechanical one is almost fool proof. I have a mechanical oil gauge mounted under the dash. I kinda hate to clutter up anymore tho. but thats me.
 

Attachments

  • fan spacer.jpg
    fan spacer.jpg
    13.7 KB · Views: 105

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Many EB's didn't even run a spacer. It's all about whether your fan blades are too close to a hose or other component, and/or if it fits properly in the shroud.
I'd say play it by ear and don't worry about a spacer unless it would improve the fan positioning to your advantage.

Paul
 

73azbronco

Contributor
Bronco Guru
Joined
Nov 11, 2007
Messages
8,782
Susan, one question, you're asking us for advice?:) Sierra Vista? OK, two questions.
 
Top