• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Cutting NWMP stock pickup. Advice please.

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
Modifying my NWMP tank with 4 Walbro pickups and am trying to find the best way to continue to use the stock pickup in the system so I don't have to mess with a bulkhead fitting.

If you look at the picture you can see the original pickup is welded all the way at the bottom and near the end. There is another weld at the bulkhead where the pickup exits the tank. The end is flush with the bottom of the tank so I cannot slide a piece of 3/8" rubber fuel line onto it.

I will need to cut this metal line somewhere to attach my rubber line. Re-welding the metal line further up is not really an option because it is slightly angled away from the wall and there is a pretty large gap which isn't evident in the picture. I suppose I could bend the tube, but I really don't want to rock the boat.

I have RE magnets holding all 4 Walbro pickups in place and another holding the TEE fitting with the barb for the 3/8" hose that will go to the stock pickup, so the assembly is very secure.

The questions are:

1. Where is the best place to cut the metal line so I don't introduce fatigue of the weld at the bulkhead?

2. Does anyone have an alternative solution?

Thanks.
 

Attachments

  • IMG_20170210_173745.jpg
    IMG_20170210_173745.jpg
    75 KB · Views: 109
  • IMG_20170210_174400.jpg
    IMG_20170210_174400.jpg
    78 KB · Views: 105

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
I would be most tempted to grind/cut through the bottom weld and pull the original tube towards the center. This would add clearance below and beside the tube to fit the rubber hose around it.
Clamping the hose and using your same magnet retaining system on that end would reduce or eliminate any additional fatigue factor from the original I would think. Only if the original weld or the tube itself was compromised already would it be an issue.

This would let you avoid cutting the tube itself. Just cut the weld (assuming you can get some kind of implement of destruction in there) and pull.

Paul
 
OP
OP
chuzie

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
I considered that too. My only concern, as you mentioned, would be getting the dremel in there to sufficiently cut the weld and clean it out enough. Fortunately I made two access holes so I can work with two hands inside per the recommendation of nvrstuk.

Thanks for the recommendation, I'm liking it though I would need to order another set of magnets from Amazon as I only have 5.
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,625
Loc.
PNW
Looks like you're making progress Chuzie! Your pics turned out better than mine... don't worry about clean up. You can slosh water around in there till it's flushed then use some gas.

What access covers did you use? Shoot me a pm. I'll be opening mine up again when I get to that point...

BTW, have I told you yet this month how much you're gonna love those 4 pick-ups...one in each corner... you'll be trying every rock combination and angle possible with only 2 gallons of gas in the tank trying to see how little gas it will run on!! lol

Keep us posted on how it goes.
 
Last edited:
OP
OP
chuzie

chuzie

Bronco Guru
Joined
Jul 21, 2006
Messages
2,761
I ended up making my own. The tank is 16ga so I used 14ga plate and cut my holes 4.5"; enough to fit my arms and reach one over the top of the baffle and they worked perfectly. I will post up more details and pics when I'm done.
 
Last edited:
Top