• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Search results

  1. JSBX

    Troubleshooting: shudder / clunk noise after trans swap

    Check your rear spring u bolts to make sure they are torqued to spec. May not be your problem but cheap and easy to check. I had a similar problem turned out to be the u bolts were loose.
  2. JSBX

    U-haul auto transport trailers

    I would only use tire or axle straps. I hauled my bronco on a 20 hr. round trip through some bad rainstorms with a Rampage soft top with very little water getting inside. On a long trip there is no telling what kind of weather you will run into, so I vote the Rampage top. I would not use a car...
  3. JSBX

    Top half cover

    I would be interested in one for a half cab.
  4. JSBX

    Fox body EFI

    Running one on my 69. Has a 1" body lift but not necessary.
  5. JSBX

    A/C line routing help

    Do a Google search. Type in what you are looking for such as Vintage Air Gen V A/C hose routing Classic Broncos. It should bring up several post on the subject. I have had good luck searching this way.
  6. JSBX

    4R70W Overdrive

    You still have to connect to a throttle position sensor. there is an orange, green and black wire coming from the vehicle connector that connects to the TPS.
  7. JSBX

    Shout out to Viperwolf1

    I believe I got them from Amazon, but I bought them about 3 years ago. Those are Auto Meter gauges, and I used a GPS speed ohmmeter. Doing it the way I did with the bolt on plate made it easier to install the wiring harness and hook up all the gauges, switches and AC controls. Worked out pretty...
  8. JSBX

    Shout out to Viperwolf1

    I cut the center section out of my original dash and left a 1" border. Had a guy cut out some plate and all the holes with a CNC. Installed rivnuts in that 1" border on the original dash. Bolted it in with 1/4" black ss button head bolts. The glove box is from a boat supplier. Still need to...
  9. JSBX

    Shout out to Viperwolf1

    I want to give a sincere thanks to Viperwolf1 for posting diagrams and instruction sometime in the past for using toggle switches instead of factory switches in the dash. I just installed a custom dash and used rocker and push button switches for my ignition, lights and wipers. I may not have...
  10. JSBX

    4’ x 8’ Plywood or Drywall in bed

    You could build a rack out of 1 1/4" square tubing or pipe with 4 legs with plate for feet that will set on the bed floor. make it just tall enough to clear the fender wells. it would be easy to put in or take out as needed. Put some eyebolts in the seat holes or seat belt holes to strap it down...
  11. JSBX

    Best electric fuel pump for carbureted set up?

    I run a Carter P4070. I can't hear it above my exhaust, but my exhaust is not very quiet. It does not shut off after building pressure. I have been running it for 5 years with no problems. I have Q jet on a mild built 351W.
  12. JSBX

    THOUGHTS ON HALF CAB

    I run a 1/2 cab and love it. I had a bulkhead built for it that goes straight down instead of angling toward the front. I have a regular console between the seats and there is a little room behind the seats. The only problem going this route is sealing the bulkhead where it meets the ribbed...
  13. JSBX

    Minimum Setup For “Easyish” Trails

    I don't see a roll bar or cage in your Bronco. I strongly suggest checking into at minimum a roll bar but better yet a cage. Our Broncos tend to roll easier than some other offroad vehicles and the top and windshield frame offer very little protection. I had two different friends that rolled...
  14. JSBX

    Viable Tachometer Options?

    Check out Max Tow gauge mount tachometer. They fit in a 2 1/16 gauge mount. I have one mounted under my dash. It is easy to see and works well. You can find them on Amazon for around 60 bucks.
  15. JSBX

    Clunking when getting on and off the gas

    Also check your spring u bolts to make sure they are tight. That should be part of routine maintenance.
  16. JSBX

    Rock rails with nerf bars using nut zerts

    I have the ones from Duff. They came with 3/8 ss button head bolts, nut zerts and a flat bar with 5/16 nut welded on them to match the holes in the back side of the sliders at the bottom. if I remember correctly the flat bar sandwiches the bottom of the rocker panel to the slider. They have been...
  17. JSBX

    Scissor Jack

    I have a couple scissor jacks that I use. I welded on old 1/2" drive impact socket where the handle goes so, I can use an impact wrench. They work great for spreading things apart also. As long as you are on flat ground, they work great for lifting a Bronco just make sure you get one big enough...
  18. JSBX

    Bronco Script/302 Emblem Install

    I would try making a template with some thin scrap metal or cardboard. Once I got them to fit right on the template just transfer it to the fender. Old plastic dealer plates work good for the template also.
  19. JSBX

    Rear Bumper with Tire Carrier build project.

    Great job on the bumper.
  20. JSBX

    Timing issues

    I run a DUI on mine. Been running it for 15 years with no problems.
Top