Search results

I Will Come Down To 2500

i have a 71 bronco that has 31 spline axles in rear,new 4.56 gears front and back with spool in the rear.the motor is a 302 with basically every yhing aruond it new.fuel pump,starter,alt,rebuild carb.it has a pto winch,35 inch tires.bronco was originally half cab but i have both tops.it has a...

i hate to try and sell it but i have got to in order to buy a rhino.it is a 71 with a 302,3 on the tree.it has brand new flow kooler water pump,new 31 spline axles,new 4.56 gears,new fan shroud.all has less than 10 miles.it has 35 inch mud brutes.i have had this bronco for 5 years and dont have...

i am tring to replace my waterpump and had 3 of the bolts break.two i was able to get out but one will not move.tried welding a nut,tried drilling and screw extractor but nothing.what to do.also where can i find what size the bolts are to the water pump?

what direction does the fan turn?cw or ccw my engine is stock

is the taurus fan a good route to go?or shuod i stick to machanical.my bronco is not a daily driver i usally go slow mudding,deer lease,whatever what to go with.also is the flowkooler what pump a good choise?

what size fan can you run with the factory or aftermarket shroud?the shruod on my is not off a bronco i think because it is turned upside down and will only work with a 15 inch fan.i am also changing the water pump at this time what should i go with?orealliys has a edelbrock avaliable but the...

I Do Not Have A Shroud.the Bronco Has A New 190 Thermostat And A Cleaned Out Radiatior.it Does Not Have A Blown Head Gasket It Takes It A Little While To Get That Hot.but If You Kill It When The Temp Is Up It Does Not Want To Start Until It Cools.what Can I Do?waterpump,shroud,rebuild?

I Have A New 190 Themromastat And Clean Radtator And Still It Run Ss To 220-230 What To Do

i ordered some parts from two differt vendors and did not receive every thing i ordered.the rear axles i ordered they did not put in the axle retaining plates.where would i be able to get theses i need my bronco going by this next weekend.but i also ordered a spool and did not recive it.so i am...

I Have A 31 Spline Spool An Want To Order The Axles To Fit It My Rear Is A Small Bearing .jbg Has The Axles For This,are There Any Downsides Or Anything Else I Need

my drums are 11 inches and i am pretty sure it measures 3 1/2 one way and 2 the other if this is the case and i wnat 31 spilne with a spool besides that what else do i need?

will a np435 from a 390 fit on a 302?

I Have Seen Those But They Are Not Bolts It A Rectangular Flat Plates Rounded On The End.

Where Is The Backing Plate Sorry To Ask So May Questions But I Dont Know Much About Axles

Do I Need To Pull The Wheel And Brakes Off To Check It

THAT JUST CONFUSES ME EVEN MORE AT WILDHORSES ALL I KNOW IS I HAVE A 71 WITH EITHER BIG OR SMALL BEARINGS?

How Do You Tell If You Have Big Or Small Bearing 9 Inch?pull The Tire?,measure What?also I Want To Go With 4.88 Gears The D44 In The Front Now Has 350 I Have Another Axle With I Think 4.10 On The Ring It Say 45 11.can I Use The Carrier From The 4.10.inthe Rear I Want To Go With 31 Spline With A...

right now i have 35s but after i get everything right i will run 37or 38.the trans is a 3 speed i want a np435 but can not find one.

i am about to get new gears and rear axles. i have a 71 and want to go with 31 spline but do not know what bearing size it is.i also thought about a spool for the rear but not sure how bad it is on the tires.i maybe would drive it once a week on the streets,maybe even once a month.also have 35...