Search results

Explorer, My email is carlberg.paul@gmail.com Thanks, Paul

Good point, some day I would plan to. Right now with everything else in life to soend money on, I only have about a 100.00 budget. So that's why I'm just looking for a cheap 3 speed to swap for now. Do you happen to know if thw housings can be switched like I was asking? Thank,

New Question Hi Guys, I took off the inspection plate and found one of the gears was broken. I didn't buy it. However here is my new question: The trans I have now has a large crack on the housing so it leaks fluid pretty bad. Hence wanting to buy a new transmission. The housing on the...

Good point. It comes with the D20. 100.00 for the pair and 25 miles from my house so no shipping. Seemed worth it. Ill either keep or sell the D20, not sure yet. Thanks for the pointer on the top plate.

Hi guys, I'm buying a used 3 speed transmission today. I'm told is was operational when it was taken out, but the guy I'm buying it from never put it in his bronco. I'm just wondering, is there an inperction plate, or any methods to check if a manual transmission is good/functional before...

Hi Guys, I'm looking for pictures or ideas on what to do with my quarter panels. The bottom portion of both rear quarter panels are rusted out or off as well as the taillight panels just below the tailgate bushing. I don't plan to replace the quarter panels as I'm looking for an inexpensive...

Hi Guys, I have a manual "three on the tree" transmission with a bad crack on the transmission housing fluid leaks everywhere so I found a used one that I plan to swap out coming up in the next couple weeks. Just a note the used transmission still has the dana 20 transfer case attached to it...

Im interested in the roll bar. Contact me when you can. Thanks, Paul

Thank you Viperwolf Hi Viperwolf It was the turn signal switch like you said. I replaced it today and now I have functional brake lights! Thank you! Paul

I have power to the brake light switch both side when depressed (so the brake light switch works fine). But no power to the brake lights. Both turn signals work fine keep in mind. I have a new headlight switch already installed. From reading past posts the wiring in the steering column is...

Thanks, I will check the wiring and post back then. I just replaced the headlight switch (thinking that would fix the problem) so that is only a week old. I replaced the headlight switch also because the headlights after running for a bit, would turn on and off erratically. The new switch...

still no power to the brake light switch. turn signal and running lights work fine. I'm gunna get a steering wheel puller tomorrow from the parts store and take a look to see if the brake light wire at the turn signal switch harness is loose. However just looking to double check. Does the...

Hi Guys, I'm a new owner of a 68 half cab. The transmission is a 3 speed (shifting on the column). I noticed the upper left side of the transmission housing has a crack on it that was patched with JB weld by the PO the patch is stating to peel off (as expected) It leaks out slow, but I want...

Thanks, If the power comes from the Headlight sw, than that eliminates a short in the turn sig switch at the steering column as a possibility then right? Paul

Hi guys, So I have been dealing with headlight, turn signal, and brake light issues. I replaced the headlight switch and that took care of my headlight & turn signal Issue. However it didn't bring power to the brake light switch. I have read that there can be shorts in the turn signal switch...

Well guys, I'm embarrassed to say that it ran out of gas, and that's why it stalled in the first place (fuel gauge does not work). I need a new pigtail for that. But it would not turn over because of battery charge. It had enough to run the fan and radio but that's it. Earlier in the day...

Hi Guys, I'm new to early bronco's and a new member to this site. I'm wondering if you guys can help me out. I was plowing snow with my 1968 bronco just now and I stalled it (manual tranny). When I tuned the key, it would not crank! Keep in mind a couple things: --wiring is not the...