Search results

Early Bronco Golf Cart on EBAY http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&category=40155&item=7155276429&rd=1&ssPageName=WDVW

bumper buy Is it to late to get in on the mass bumper buy? I need one for a 76EB with 2" body lift.

I'm looking for a new extreme rear bumper for my 76 EB. I have the stealth front bumper and now need something for the rear. Want one without a tire carrier on it in the $250 range. NO PRE-RUNNER style bumpers! Any ideas?

The front bumper in the Stealth bumper, I just added the hoop to it. But I think I'm going to build a rear bumper just like it.

?:? I haven't started my EB in about 2 years because the top end on the motor was apart. Got it back together about amonth ago and it been starting and running fine. But as of Friday it will start up fine but the starter keeps running, No matter what postion the key is in. If I turn the key off...

Beleave it or not I just used one of those $79 manuel pipe benders you can get at Northern Tool. It's a 12 ton jack with three differant size 90 % pipe dies. I used 1.90 OD pipe, Had it all welded together with a arc welder.

I just finished bending,cutting,and welding in my roll cage, Front bumper hoop, and nerf bars. Check out my pictires and tell me what you think? ;D http://pg.photos.yahoo.com/ph/ruthamartin/album?.dir=989f&.src=ph&store=&prodid=&.done=http%3a//pg.photos.yahoo.com/ph/ruthamartin/my_photos

Yes the pitman arm is installed, and so is the adjustable trac-bar. I pulled the Bronco out of the garage today to get a better look at the front end. It seem to be towed in a lot. I will try to adjust the tie-rods tomorrow.

I read all these emails last night. I have the stock inverted Y set-up. I added a adjustable trac-bar, and I do have a drop pitman arm on it. The Bronco steered fine before I lifted it. I haven't tried to adjust the tie rod yet. And no I haven't tried to reinstall the pitman arm yet. i will try...

I just got finished lifting my 76 EB. I put on BC bronco's 3 1/2" front springs and the 1"lift spring plate shims, Also added their drop pitman arm and Duff's long travel dual shock hoops. Now the front wheels don't turn to the right or left fully. Can't even turn enough to get out of my...

I just got my 76 Bronco running again (after two years of sitting) I put a new set of Hooker Headers on it . Now I need to add an exhaust system. Anybody have any ideas or advise? I found a exhaust kit in JC Whitney for $149. Anybody ever installed one of these before?

FYI I put a set of warflares on the front and rear of my 76 EB and before I lifted the truck I could fit 36" tires on it at the stock height. THESE FLARES ARE GREAT !!

What axles is in the rear of my 1972 Bronco? I know it's a 9" but is it a small bearing or big bearing, 28 or 31 spline?

Does anybody need a vehicle transported from the Atlanta area to the Little Rock, Arkansas area? I'm going that way with my car hauler and could make you a good deal on shipping. Jim 678-358-6193

I just installed my National leaf springs (11-pack 3 1/2"lift) in my 76 EB. Now the pinion angle looks off, Was I suppose to add a leaf spring shim with an angle on it? if so where can I get one ASAP? Atlanta,GA.

are all early Bronco front Dana 44 axles considered a high pinion axle.

how do I remove my windshield frame on my 72 Bronco? Does it have to be cut off or what? :-[

Has anybody done one of those gear reduction kits for a dana 20? If so what kit is the best for the money?

I still haven't recieved my new issue of Bronco Driver magazine !!<br>What's up?

The first thing that I did to my 76 Bronco was put on a set of Gorrila Warflares. I stretched them out as far as I could and cut the fenders to fit them. With no lift kit on my Bronco yet I can clear 36x12.50 SuperSwampers on 10" wheels WOW!! (I don't drive it like that) My trucks still under...