• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

1976 front end axle

rjcruz27

Sr. Member
Joined
Dec 2, 2014
Messages
369
I have a 1974. I found a complete front axle with disk brakes from a 1976. I’m assuming it will all transfer over. Is this correct?
 

thegreatjustino

Contributor
Red Head Grease Monkey
Joined
Jan 23, 2002
Messages
16,291
Loc.
Stockton, CA
Tie rod and drag link set up are different. Your existing setup won't fit without modifications. The setup on the '76 won't work with your '74 pitman arm. Depending on the back spacing of your rims, they might not bolt on to the '76 front end without hitting the knuckle due to the different design.

It is for the most part a bolt on, but there are a few nuances to address.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
Good axle to get. For the most part it will bolt right in. There are a few little details that are different. Differences are in the track bar and the steering.
 

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
The only difference in the frame is the tracking bar bracket. You want all the steering linkage including the pitman arm. The steering gear will work. The back spacing on the wheels has to be less than 3.75". Many wheels made for CJs and '70s Trail Dusters/Ramchargers work well with the '76-'77 knuckles. The master cylinder differs only in the side the brake lines are attached because of the vacuum booster bracket. Any disc/drum system requires a metering and proportioning valve. So all brake system changes are the same as any front disc power brake conversion. The '76-'77 version of the Dana 44 is stronger than earlier years. They are very desirable.
 

sprdv1

Contributor
REBEL
Joined
Mar 8, 2007
Messages
81,996
I have a 1974. I found a complete front axle with disk brakes from a 1976. I’m assuming it will all transfer over. Is this correct?

if at the right price, you could always have some resale value :)
 
OP
OP
R

rjcruz27

Sr. Member
Joined
Dec 2, 2014
Messages
369
This is it. He wasn’t sure on price but he was thinking $400.
 

Attachments

  • 37324E78-83E0-4715-8FC0-58B93CC08499.jpeg
    37324E78-83E0-4715-8FC0-58B93CC08499.jpeg
    61.5 KB · Views: 159

JSBX

Contributor
Sr. Member
Joined
Mar 10, 2010
Messages
652
Make sure the gear ratio matches what you have now. That is a good deal.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
Depends on location and condition, I'll ballpark $500 - $1000 in good condition.
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
Before going out and sourcing an inverted "Y" steering linkage, you can make that '76 axle work great with new parts from our vendors.
An aftermarket "T" steering linkage if available from both Toms and WH that is made to use on a '76/'77. You'll also need a dropped pitman arm. Just tell them what you're doing and they'll set you up.
Also, the track bar can be replaced with an adjustable.
I've done both of these mods to my '77 and I'm very happy with the handling.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
I may be wrong, but that long link looks bent. Well, at least bent more than normal.
You can still try it, but I prefer the custom T-linkage route like mentioned anyway.

If you use the existing Y-linkage that comes with the axle you will need either the '76/'77 pitman arm (smaller hole) to suit, or use one of the tapered sleeves available (if they are the correct size).
I think I trial fitted some of our sleeves to do this and found that it would work, but I don't remember for sure.
They're specifically slated for flipping your tie-rod over to the top of the knuckle, or the other one is for fitting a standard '66-'75 Inverted-T linkage into a full-size truck knuckle and/or pitman arm.

You can also ream out the new knuckles to fit your older tie-rod linkage. It's been done, but also argued that the knuckle is already smaller than the old ones so reaming out can possibly weaken it. Whether it's to the point of it being a problem I don't think has been determined.
Might depend on how you use your Bronco.

Paul
 
OP
OP
R

rjcruz27

Sr. Member
Joined
Dec 2, 2014
Messages
369
Anything negative stand out to you guys?
 

Attachments

  • B33B090A-2D75-4FCC-98D1-8A410072070C.jpg
    B33B090A-2D75-4FCC-98D1-8A410072070C.jpg
    147.2 KB · Views: 67
  • 989F44FE-1677-448B-BD50-9581E32038B7.jpg
    989F44FE-1677-448B-BD50-9581E32038B7.jpg
    132.9 KB · Views: 67
Top