• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

250 I6 Engine OIL Pan for Bronco

Ohio Bronco 21

Bronco Guru
Joined
Dec 5, 2006
Messages
4,194
Loc.
Cleveland
I figured I would make a specific post on this. Has anyone cut a 250's oil pan and re welded it reverse to move the sump to clear the front axle?
Not a lot of these engines seem to have been sourced into the Broncos. Hoping for pics as I may have to just try to do it myself.
Some members have this but either ran a huge lift or had the pan on to begin with. Thanks for all prior and future help.
 

Explorer

Bronco Guru
Joined
Mar 2, 2008
Messages
4,390
Loc.
Raphine, Virginia
I know this swap has been made. But the people that have done it may not visit here anymore, or just miss this thread. You're going to have to do like I am. Just pull the oil pan and figure it out. Then post back with a "how to" for the next guy. I'm finishing up the doors on my 66 this week, but hope to get to it end of the week. Still looking for another Bronco to put it in, so it hasn't been at the top of my priority list.
 
OP
OP
Ohio Bronco 21

Ohio Bronco 21

Bronco Guru
Joined
Dec 5, 2006
Messages
4,194
Loc.
Cleveland
Yeah, Im not in a hurry but I like to have as much tech mapped out in advance before I do something. I will probably get the pan off in the next week and start trying to figure out the pan and pick up.
I really like this engine anyhow, had it running for a while before I pulled it down.
 

Attachments

  • 003.jpg
    003.jpg
    122.8 KB · Views: 166
OP
OP
Ohio Bronco 21

Ohio Bronco 21

Bronco Guru
Joined
Dec 5, 2006
Messages
4,194
Loc.
Cleveland
Update, I pulled the pan (snapped a couple of pan bolts off and had to drill and tap them).
The pick up is indeed in the way up front and the pan itself expands out on one of the sides so a clean 180 degree spin wont happen. If one was to pound the pan in a bit it could give some more clearance. (dont like this)
I have decent clearance for a non extreme off roader right now. I believe I may take the stock 170 engine engine mounts and modify them so the engine sits 1 inch higher. This should be pretty good, also I will get some higher front axle bump stops to be sure. I plan on running a 2 inch body lift on this thing. The 2 inch should be good for the added height of the engine and the 1 inch lift of the engine by the engine mounts. Now that I have this pan off I need to scrub, clean and paint it anyhow, new gasket wont hurt either.
 

Explorer

Bronco Guru
Joined
Mar 2, 2008
Messages
4,390
Loc.
Raphine, Virginia
Got around to looking at it today. The pickup tube could be extended so I don't believe that part would be too much work. Pic's below of a 200ci oil pan spliced into the 250ci pan. Found them over on fordsix.com. If I build this project, I'm planning on a suspension lift and I believe a 3.5" lift will do it without fooling with the pan. Going to scoop the hood anyway so not worried about the height. More garage engineering to do, we'll see.
 

Attachments

  • Fox2503vexh.jpg
    Fox2503vexh.jpg
    84.9 KB · Views: 98
  • Fox2503vpan.jpg
    Fox2503vpan.jpg
    108 KB · Views: 96
OP
OP
Ohio Bronco 21

Ohio Bronco 21

Bronco Guru
Joined
Dec 5, 2006
Messages
4,194
Loc.
Cleveland
I believe the stocker pan will work fine with any suspension lift. I am def going to make the motor mounts lift the engine by an added inch and do the taller bump stop thing. With the engine and trans in I had 4 inches between the closest points on the pan and the diff. Adding the inch should help.
 

chrlsful

Bronco Guru
Joined
Oct 21, 2009
Messages
1,448
OB21-
Be careful rasing that motor! They hit the hood real easy. Save your 170 pan & weld 1/2 THAT to the 250's. U may not even need to do that w/a minor suspension lift.

I've had a '70 EB 170/2.8 since '82 (work truck, not rec vehicle). Over the past few yrs have IDed the motor as a car ( '68 "Falcon I6") because it has a dip stick on each side! 1 in block - D side, 1 in pan - P side. THAT hits the hood w/o a "air cleaner peg" (the threaded bail the center of the ac filter housing sits on).

A Vermonter put the 250 in his EB by combining the 2 pans. A Cal guy put the 250 in w/o pan mods but a sm lift.
 
Top