• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

351W Backfiring on Shift

pbking

Jr. Member
Joined
Feb 25, 2016
Messages
73
I've got a backfire happening when I shift too early. When I go from 3 to 4 when the RPM are a bit too low I get a lurch and a couple of pops out the tail pipe. This has also happened when I take too long when shifting and coast for a second or two(I've got to get my shifter fixed! I swear those gears move around).

So am I just a crappy driver, or is there something to tinker with and see if I can get it fixed? Where should I start? I've read that if I get backfires when downshifting, it may be a timing issue, does the same hold true for upshifting?

Thanks for any input and pointing me in the right direction!
 

SHX669

Bronco Guru
Joined
Jan 9, 2009
Messages
1,997
Sounds like your carb might be running too rich. What carb , what size ? Also what ignition system ?
 
OP
OP
pbking

pbking

Jr. Member
Joined
Feb 25, 2016
Messages
73
It's a motorcraft carb, I haven't pulled the number off of it yet, I can get it tomorrow. It has a non-vacuum mallory distributor.

I haven't had the bronco long, but I think it runs pretty well, starts right up and idles/runs like a champ.
 

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
Motorcraft made all kinds of carburetors. Just the ones sold on 351s included 2100s, 2150s, 4300s, 4350s on the 351C and 2700 variable venturis. If carburetion is ruled out, retarded timing is a more common cause of back fires through the exhaust.
 
OP
OP
pbking

pbking

Jr. Member
Joined
Feb 25, 2016
Messages
73
Well, I didn't find any direct numbers on the carb to give me any kind of certainty as to which model it is. Comparing pictures it looks like a 2100, but take a look and let me know if I'm wrong.

The timing is around 12-14*.

Thanks for the help!
 

Attachments

  • IMG_1389.jpg
    IMG_1389.jpg
    122.7 KB · Views: 67
  • IMG_1391.jpg
    IMG_1391.jpg
    115.6 KB · Views: 53
  • IMG_1393.jpg
    IMG_1393.jpg
    94.9 KB · Views: 61

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
That's a 2100, that may have been on the 351 from the factory. The driver side of the float bowl will have a number cast on it, likely 1.21 or 1.23. 351Ws usually were 1.23 and 351Cs were mostly 1.21. The 2100s aren't likely to be the cause of backfires. 12-14 degrees initial timing shouldn't cause it either. The compression ratio changes over the years. The 2bbl 351Ws were 9.5 to 1 from '69 to '72 and 8.7 to 1 in '73- '76. Do you know what year the engine is? I don't see an EGR so it's likely pre '73. So it may take 16 degrees initial timing but not much more. That leaves some of the less likely causes. The plug wires may not be in the correct firing order. An exhaust valve may be burnt or bent. A compression test will tell. Another thought is a retarded cam. Ford retarded the cam timing in '72 and on. A worn timing chain may have aggravated this.
 
OP
OP
pbking

pbking

Jr. Member
Joined
Feb 25, 2016
Messages
73
Awesome help, thanks a ton!

I have paperwork from the PO showing they had the engine worked on and part of that was "fix firing order", so I of course thought it would be right. They set the order to 1-5-7-2-6-3-4-8. I can't find that firing order anywhere. I changed it to what several sites said would be the 351w order, 1-3-7-2-6-5-4-8. It ran rough as all get out, so I tried 1-5-4-2-6-3-7-8 and she purred like a kit drunk or milk and cat nip. Took it down the road a couple of times and couldn't get the thing to backfire to save my life!

Unfortunately, when I got home and shut it off, it dieseled like crazy! I finally had to keep pressing on the accelerator to flood it to get it to die.

One other thing, on the picture below, I circled what I believe to be the choke tube connection that should go to the exhaust manifold. You can see that it doesn't. It just sits there pulling a strong vacuum all the time. Since the choke is temperature activated and I live in a warm climate, how much of an issue is having that just open? Any reason I should plug it, or would that make matters worse?

Thanks everyone for the help!
 

Attachments

  • Choke Port.jpg
    Choke Port.jpg
    96.8 KB · Views: 60

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
The firing order is determined by the cam. The cams for Windsor small block Ford engines will "fit" in either block. So without knowing what cam you have, you can't be sure what the firing order is. Sometime around '90-'91 Ford changed the 302 firing order to match the 351 order. Your cam must be the early 289-302 version. The weird 1-5-7-2-6-3-4-8 is for some other engine line. Now that you have that corrected, the idle is much stronger and needs to be slowed at the idle speed screw by the throttle lever and shaft to something like 650 RPM, by turning it counter clockwise. That should cure the run on, after the ignition is shut off.
The choke connection you point out needs a hose to the capped nipple above and behind it to supply filtered air. The auto choke needs air to work and the hot air plumbing is missing. To heat the bi-metal spring in the choke cap opening the choke as the engine warms up, you need an electrically heated choke cap. Here's one from Carbs Unlimited; http://www.carburetion.com/Products/ProductDetails.aspx?part=EC-5106C.
The capped nipple in front of and below the choke housing is the ported vacuum source for the vacuum advance on the distributor. I would hook that up too.
 
OP
OP
pbking

pbking

Jr. Member
Joined
Feb 25, 2016
Messages
73
Great help!

I don't have anything to let me know the RPM currently, so I adjusted the idle until the engine started to stumble then increased it just until i smoothed out. After this evening drive, no dieseling what so ever!

I will take a look at plumbing the choke intake to the fresh air port as you suggested, as well as replacing the hot air choke with the electric. Right now, I know the current choke never closes, so I'll have to fix something. I was thinking about converting to a manual choke since I already have the knob in the cab.

As for the cam, I read about using 302 cam in 351W, but never got any definite feeling as to this being a positive, negative, or no difference. Are there any advantages to changing to cam that uses the 351 firing order?

Once again, thanks much for the help, things are MUCH better now.
 
OP
OP
pbking

pbking

Jr. Member
Joined
Feb 25, 2016
Messages
73
That's a 2100, that may have been on the 351 from the factory. The driver side of the float bowl will have a number cast on it, likely 1.21 or 1.23. 351Ws usually were 1.23 and 351Cs were mostly

I finally remembered to check mine and it is stamped with a 1.08. Does that designate a smaller version?
 

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
The 1.08" veturi diameter is the size sold on 302s. Maybe whoever swapped in the 351 just kept the original 302 carburetor. It may give better MPGs and low end torque at the expense of a little top end power. My 351 has a 4bbl 4100 model with the 1.08" venturis to cover both needs. There's no problem with the small 2100. The 351 firing order supposedly puts less strain on the main bearings. I doubt you will see any difference, and swapping the cam is too much trouble, without a good reason. The firing order cast into the top of the intake is no longer accurate, but you didn't use it anyway.
The Ford 2100-4100 carburetors are very difficult to change from automatic to manual choke and visa versa. I've done it on my 4100, using modified parts from a manual choked 2100. It's far easier for you to buy a manual choked 2100. Here's a good example of what I mean;http://www.ebay.com/itm/Ford-motorc...-manual-choke-autochoke-/322094767050?hash=it. On the other hand the automatic choke can be refurbished to work well, by simply getting a rebuilding kit, you get parts and instructions on how to set up the whole carb including the choke. Engine analyzers are cheap and include a tachometer. You may want to pick up a vacuum gauge and timing light too. Welcome to the pre-computer world.
 

67RT

Bronco Guru
Joined
Jan 17, 2014
Messages
1,308
Check float level and rear vacuum ports for leaks. Mine was doing the same and it had a crack on the large rubber port seal on the rear of the carb. Dieseling may be by rich idle mix screws, the fast idle adjustment too high,or the float level. Do the idle mix screws to highest vacuum, then set fast idle..
 
OP
OP
pbking

pbking

Jr. Member
Joined
Feb 25, 2016
Messages
73
Thanks everyone, the information has been awesome.

So far, the engine is running SO much better and it starts right up and turns off when I kill it. No backfires anywhere. It's running so well, I hate to admit that I started taking apart the front end this evening for the 14pc bushing project. :p

I'm going to be picking up a vacuum gauge and engine analyzer soon as well as getting the choke fixed.
 
Top