• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

480 hp on dyno today!

sicaz66

Bronco Guru
Joined
Aug 14, 2001
Messages
1,951
Loc.
san diego
;D dynoed my 408w today.480.3 hp at 5700 rpm.not too bad running off a non tuned 750 cfm holley(shop not setup to dyno efi).torque was at 399.9 at 2600rpm torque maxed 475 at 4600 rpm.very smooth running with a nice crisp throttle response.ran best when timing set at 32 degrees.no jetting or carb work done(they used an inhouse victor jr. intake and 750 carb estimated on the jetting ) should hit 500 with proper jetting but no sense in paying for it when it`s not my carb. efi should be same hp or better.basically ran it to make sure all is well and to do a proper break in. 9.25 compession and runs like a raped ape! should be a very strong reliable motor. motor was ran under a full load to produce real #`s not unloaded dyno crate motor #`s.would probably hit closer to 600 on an unloaded dyno run.
 

mustangmarty

Bronco Guru
Joined
Apr 1, 2003
Messages
1,229
Rockin! I got my 408 dyno'ed a couple months ago. Can't remember the hp. I think it topped out around 475. Torque though came out at around 425 at 2400 under a load. I couldn't wipe the smil off my face no matter how hard I tried to retain my manly composure. 69 motor bored .30 over. Trick Flow Twisted Wedge heads. Weiand Stealth intake. Crane roller rockers. Edlebrock 650 carb. Headman shorties. I started building it a couple years ago hoping to find an EB to put it in that I can afford since all my money went into the motor. Anyway, congrats on your Windsor. I know the euphoria you're feeling!
 

Dusty

Bronco Guru
Joined
Jun 28, 2001
Messages
2,969
Awesome numbers, Jason. So are you gonna tell your wife about it now or just tell her you're running "race gas" when she asks about the "improved" throttle response? ;D

Dusty
 
OP
OP
sicaz66

sicaz66

Bronco Guru
Joined
Aug 14, 2001
Messages
1,951
Loc.
san diego
just gonna tell her i need new exhaust.then act surprised at the new found power. ;) too bad it won`t be in the bronco for a few more months though :- still gotta get the c-6 built and pay off the rest of it.(we over shot original estimate by about $2000.00 :() so can`t build trans until i finish paying for it. kinda bummed i didn`t hit the 500 hp mark like i had planned but shop guy said it wouldn`t be a problem with proper tuning.all they did was add oil, bolt on the carb, intake and mess with the timing.should still eat rice and a few big block heeps!
 

Desert Thrasher

Bronco Guru
Joined
Jul 14, 2001
Messages
2,353
Thats awesome man,
What do you think it will put out at the rear wheels? I had my cleveland chassis dynoed at JBA awhile ago, it was fun. I cant wait to go back when I get my Aussie heads done, I am hoping to put out bout the same as yours at the flywheel, so on the chassis will be less.
 

supermottl

Bronco Guru
Joined
Feb 18, 2002
Messages
2,360
Loc.
Indian Harbour Bch,
Newbie motor question here... how much does it cost to build up a motor like that?

And about how much would it cost to build up a 351 to be abuot 350HP and similar torque numbers?

those are ungodly numbers. Hope you don't rip the EB apart with it!!! ;D ;D
 
OP
OP
sicaz66

sicaz66

Bronco Guru
Joined
Aug 14, 2001
Messages
1,951
Loc.
san diego
[quote author=Desert Thrasher link=board=5;threadid=16430;start=0#msg125108 date=1050477487]
Thats awesome man,
What do you think it will put out at the rear wheels? I had my cleveland chassis dynoed at JBA awhile ago, it was fun. I cant wait to go back when I get my Aussie heads done, I am hoping to put out bout the same as yours at the flywheel, so on the chassis will be less.
[/quote]

to be honest. i have no clue ??? ::)
 

cadun

Jr. Member
Joined
May 8, 2002
Messages
94
Loc.
Santa Barbara &amp San Francisco, Ca
[quote author=supermottl link=board=5;threadid=16430;start=0#msg125116 date=1050494169]
Newbie motor question here... how much does it cost to build up a motor like that?

And about how much would it cost to build up a 351 to be abuot 350HP and similar torque numbers?

those are ungodly numbers. Hope you don't rip the EB apart with it!!! ;D ;D
[/quote]

I was wondering the same thing. Anybody have some rough estimates?
 

JaxLax

Bronco Guru
Joined
Apr 22, 2002
Messages
3,310
Loc.
Jacksonville, FL
Engine is on the list to come, but I built the tranny first (C6 from an F150 rebuilt). She'll hold 450hp easy, too bad I'm shooting to build the engine in the 350-400hp range :p I know, it's blasphemy, but 500hp is too much for me. I have a bad habit of being caught by the bacon... :-[
 

Madgyver

Bronco Madman
Joined
Jul 30, 2001
Messages
15,030
Nice numbers Jason!!, Now you got to build the trans to handle it.. :D

Can't wait to start and assemble mine. I still got a cleveland on the engine stand....
 

mustangmarty

Bronco Guru
Joined
Apr 1, 2003
Messages
1,229
[quote author=supermottl link=board=5;threadid=16430;start=0#msg125116 date=1050494169]
Newbie motor question here... how much does it cost to build up a motor like that?

And about how much would it cost to build up a 351 to be abuot 350HP and similar torque numbers?

those are ungodly numbers. Hope you don't rip the EB apart with it!!! ;D ;D
[/quote]

I built mine a little bit at a time over a year or so. All tolled, I'd estimate around 5 grand for about 425 ft. pds. @ 2400 rpm. Sounds like a lot but it doesn't feel like it spread out over that much time.
Thinking back now, I wonder if I might have just gotten me a crate motor. I'm happy with what I've got though. I'm just itchin' to find an EB to put it in!
 
OP
OP
sicaz66

sicaz66

Bronco Guru
Joined
Aug 14, 2001
Messages
1,951
Loc.
san diego
just got the c-6 to dana 20 adapter.building the c-6 to match motor.(it will be awhile :p).as far as cost don`t ask(over 10 with out breaking a sweat). :-[ it cost WAY more than i had initially planned :-.
every part is damn near bullet proof though. should handle the nitrous just fine :eek: ;D 8)............can you say 700+ hp!!! ( yes,some say i may be crazy :-* )
 
Top