• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

480 hp on dyno today!

mustangmarty

Bronco Guru
Joined
Apr 1, 2003
Messages
1,229
Hey y'all, remember me? I left one of the first few posts on this thread about my 408 that I had dyno'ed awhile back but had nothing to put it in. Well, it looks like that might be about to change. Got the trailer hooked up and took today off to go check out a '77 I've been looking at for awhile now. With any luck I might be bringing her home tonight. ::) No pun intended, but "May the Bronco Gods be with me on this one..."
:) ??? ::) ;D
 

BwoncoHowie

C-4 Wizard
Joined
Nov 11, 2002
Messages
3,571
You got me drooling again...

Oooooh how I want to build another motor. :p

Congrats on the frame twisting, sand roosting, pavement scorching power.

BH
 

coby

Full Member
Joined
Apr 24, 2003
Messages
317
Loc.
Fort Collins, CO
[quote author=BwoncoHowie link=board=5;threadid=16430;start=30#msg127628 date=1051303625]
You got me drooling again...

Oooooh how I want to build another motor. :p

Congrats on the frame twisting, sand roosting, pavement scorching power.

BH
[/quote]


...and axle snapping, third member cracking, tranny roasting, ujoint exploding, tire smoking, tcase shredding, driveshaft twisting power. Hehe...it'll show up ALL the weak points. Well, except for the 28 spline axles. (grin) :-*
 

clc900

Jr. Member
Joined
May 20, 2002
Messages
57
Thats some nice power from that windsor. Just make sure you get some beef behind it. Get that thing installed and let it rip!

Dayum, First Post!!! ;D
 
OP
OP
sicaz66

sicaz66

Bronco Guru
Joined
Aug 14, 2001
Messages
1,951
Loc.
san diego
...and axle snapping, third member cracking, tranny roasting, ujoint exploding, tire smoking, tcase shredding, driveshaft twisting power. Hehe...it'll show up ALL the weak points. Well, except for the 28 spline axles. (grin) :-*

ctms and chromolly shafts for the front,nodular BB 3rd memeber in the rear,built c-6, 1350 jointed drive shafts, b.c. t-case shaft, and 31 spline curries in the rear, just gotta finish trans and it should be good to go. ;D
(i already broke all the other stuff :( :- :eek: ;D )
 

BwoncoHowie

C-4 Wizard
Joined
Nov 11, 2002
Messages
3,571
[quote author=coby link=board=5;threadid=16430;start=30#msg127641 date=1051305467]
[quote author=BwoncoHowie link=board=5;threadid=16430;start=30#msg127628 date=1051303625]
You got me drooling again...

Oooooh how I want to build another motor. :p

Congrats on the frame twisting, sand roosting, pavement scorching power.

BH
[/quote]


...and axle snapping, third member cracking, tranny roasting, ujoint exploding, tire smoking, tcase shredding, driveshaft twisting power. Hehe...it'll show up ALL the weak points. Well, except for the 28 spline axles. (grin) :-*
[/quote]

coby,
I knew that was coming. I left myself wide open for that one... ;D

Glad to see you signed on as a member.

BH
 

coby

Full Member
Joined
Apr 24, 2003
Messages
317
Loc.
Fort Collins, CO
Eh, I had to get a new membership; I can't remember the password to my old one. Kinda bites.

[quote author=BwoncoHowie link=board=5;threadid=16430;start=45#msg127864 date=1051389712]
[quote author=coby link=board=5;threadid=16430;start=30#msg127641 date=1051305467]
[quote author=BwoncoHowie link=board=5;threadid=16430;start=30#msg127628 date=1051303625]
You got me drooling again...

Oooooh how I want to build another motor. :p

Congrats on the frame twisting, sand roosting, pavement scorching power.

BH
[/quote]


...and axle snapping, third member cracking, tranny roasting, ujoint exploding, tire smoking, tcase shredding, driveshaft twisting power. Hehe...it'll show up ALL the weak points. Well, except for the 28 spline axles. (grin) :-*
[/quote]

coby,
I knew that was coming. I left myself wide open for that one... ;D

Glad to see you signed on as a member.

BH
[/quote]
 

mlogan24

Bronco Guru
Joined
Jun 14, 2001
Messages
1,380
Welcome back Coby! So are you back for good-or will we lose our Bronco God again? BTW-since you're back-do you think you fix the four pics you have of the TFS 5.8 intake article? They never seem to work. All the great pics of your switchover from the GT-40 to TFS do work-I still look at those and drool.

You tell them about the mileage! I figure with the SEFI 408 I want to do, 4.10's, and my AOD, I'll be sittin about 15-16. Just so long as I grease those wheel bearings real good! ;D ;)
 

coby

Full Member
Joined
Apr 24, 2003
Messages
317
Loc.
Fort Collins, CO
I wouldn't be surprised if you got that mileage at all...I got that 14 with 4.88's and no overdrive. (and a heavy foot at a high mph). Yea, I'm back for good. I've never REALLY left....I lurked for a looong time. I'll see what I can do about those pics...where's the url on it?
btw, I've a decent digicam now; if anyone wants pics of anything lemme know. It's a lot easier than in the old days when I took print film and scanned the negatives then ran them through photoshop.
I am considering replacing my 423 with a 5.0 stocker and slappin' the motor into some other car; I'd like to feel what that does in a lightweight vehicle. My gf wants a sports car....anyone ever seen a mazda miata with 550ftlbs of torque? (grin)
[quote author=mlogan24 link=board=5;threadid=16430;start=45#msg127995 date=1051425404]
Welcome back Coby! So are you back for good-or will we lose our Bronco God again? BTW-since you're back-do you think you fix the four pics you have of the TFS 5.8 intake article? They never seem to work. All the great pics of your switchover from the GT-40 to TFS do work-I still look at those and drool.

You tell them about the mileage! I figure with the SEFI 408 I want to do, 4.10's, and my AOD, I'll be sittin about 15-16. Just so long as I grease those wheel bearings real good! ;D ;)
[/quote]
 

mlogan24

Bronco Guru
Joined
Jun 14, 2001
Messages
1,380
Sure-the url is http://www.vintagebronco.com/coby/images/423rebuild/index0006.html -the TFS article on the bottom never loads. I have to say-your scanned regular pics are some of the best quality pics I've seen online for tech stuff.

I like the Miata idea-although, if I ever did a Miata engine swap-I would lean more towards throwing in a 4-rotor Wankel ;D

I'd save your block for an Elanor stang. Throw a little go-juice bottle on that. Your gf would never stop smilin ;D
 

coby

Full Member
Joined
Apr 24, 2003
Messages
317
Loc.
Fort Collins, CO
Not sure why the links are gone, but if you'd like, I can email you the pics of that article. I've still got them.
As far as puttin' a smile on my gf's face..she don't NEED nitrous with that motor. However......**I** might. (grin)

[quote author=mlogan24 link=board=5;threadid=16430;start=45#msg128070 date=1051478507]
Sure-the url is http://www.vintagebronco.com/coby/images/423rebuild/index0006.html -the TFS article on the bottom never loads. I have to say-your scanned regular pics are some of the best quality pics I've seen online for tech stuff.

I like the Miata idea-although, if I ever did a Miata engine swap-I would lean more towards throwing in a 4-rotor Wankel ;D

I'd save your block for an Elanor stang. Throw a little go-juice bottle on that. Your gf would never stop smilin ;D
[/quote]
 
Top