• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

5.0 clutch/flywheel

chipk

Jr. Member
Joined
Sep 26, 2008
Messages
145
Has anybody else had a clearance problem with a stock bellhouse and the 50 oz flywheel/clutch?
I am running an explorer 5.0 with a stock 3 speed bell.
Will the standard 89-93 mustang clutch/flywheel work?
Thanks in advance and sorry if this has been previously been covered.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,110
You do have the Bronco bellhousing, right?

Mustang flywheel and clutch will NOT work. the starter won't engage the flywheel. Lots of people found this the hard way doing the mustang engine swaps. The car flywheel is a smaller diameter than the truck flywheel. You need a mid 80's F150 302 truck flywheel.
 
OP
OP
C

chipk

Jr. Member
Joined
Sep 26, 2008
Messages
145
I have the Bronco bellhouse. Planning to use a mini starter. The problem I ran into was the clutch housing clearing the inside of the bellhouse.
So the mid 80's f150 flywheel and clutch should fit?
 

Ourobos

Bronco Guru
Joined
Jan 7, 2008
Messages
1,225
Loc.
Big Island Hawaii
86-93 Mustang bellhousing is for a 157 tooth flywheel, and a 10.5" clutch. The Bronco bellhousing needs a 164 tooth flywheel, which is also in the 80s F150 Broncobowsher is referring to.
 
OP
OP
C

chipk

Jr. Member
Joined
Sep 26, 2008
Messages
145
Thanks guys. I understand about the flywheel, but what clutch? Mid 80's f150 5.0?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Haha. Yep, can hear them chirping now. Just like a clutch cover hitting a bell housing...

If a Mustang clutch hits, I'm thinking a truck clutch might too. Not sure why a smaller car clutch would have been a problem in the first place though.

Got any pics of this thing?

Thanks. Sorry you're having an issue, but it's a strange one for sure. I've heard of clearance issues, but as the others were mentioning, it's usually when using the smaller Mustang bell housing and the larger truck clutches. Not the other way around.
Well, not "usually" anyway...%)

Paul
 

AWS

Sr. Member
Joined
Aug 2, 2004
Messages
596
Loc.
ST LOUIS
chip, I'll bring over some extra bell housing to compare with yours.
Steve aka "Dad"
 
OP
OP
C

chipk

Jr. Member
Joined
Sep 26, 2008
Messages
145
Got it......1985 164 tooth 50oz flywheel with 10 inch clutch. Two options for that year. 10 and 11 inch. Not sure how the 11 inch would work, but the 10 inch spins free and easy!
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
But just in case, you might consider changing them out anyway, so you can utilize the larger truck clutch. It's there for a reason.
Heavier vehicle, more low end torque from the engine (typically, but not always) and larger tires were why Ford used the larger 11" clutches on most, if not all trucks.

If it's just a quick bell housing swap that gets it done, it would be worth if.
If you're already done however, good luck with the smaller clutch. It'll work, just not sure how well. Might never give you any trouble at all of course. Could have been overkill, but look to the way you intend to drive it and have the truck set up.

Paul
 
OP
OP
C

chipk

Jr. Member
Joined
Sep 26, 2008
Messages
145
Thanks DirtDonk, I am going to look into the 11 inch that's made for the F150. That extra inch width over an entire surface area has to be better if it will fit. I'll let you guys know what I find out.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,110
I recall the first V8 Broncos had a smaller clutch. Ford very quickly changed that up to an 11" clutch

The 10" clutch in a mustang is very short lived, hence the factory upgrade to the largest clutch that would fit, the 10.5". And that is still questionably undersized in a lighter mustang.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
When I said "truck" Chip, I also meant "Bronco" because our trucks got the 11" clutches as well. Which is probably why we are questioning the fact that you're running a stock bell housing in the first place.
I don't think you said what year your truck is, or if you did I forgot. If it's a '66, then maybe that's the issue and you need a later bell housing for all this to work, or stick with the smaller clutch.

Paul
 
OP
OP
C

chipk

Jr. Member
Joined
Sep 26, 2008
Messages
145
Would changing the bellhouse to and f150 take care of it?
I am concerned about the front to rear dimension being off!
 
OP
OP
C

chipk

Jr. Member
Joined
Sep 26, 2008
Messages
145
When I said "truck" Chip, I also meant "Bronco" because our trucks got the 11" clutches as well. Which is probably why we are questioning the fact that you're running a stock bell housing in the first place.
I don't think you said what year your truck is, or if you did I forgot. If it's a '66, then maybe that's the issue and you need a later bell housing for all this to work, or stick with the smaller clutch.

Paul

Thanks Paul,

I have a 5.0 out of an exploer/automatic. The only bellhouse I have is from the early bronco. I'm not sure what year this one is...... I didn't realize there was a different in the 66 v8 bell. I do in fact have a 66, and this may be from it. I also have a 75 that I can compare to...?:?
 
OP
OP
C

chipk

Jr. Member
Joined
Sep 26, 2008
Messages
145
Got it! It was the wrong clutch housing.
I took a standard issue LUK clutch from Auto Zone and it spins free and clear now with the standard early Bronco Bell!
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Cool beans.
Frankly, I would not have known or remembered about the odd size for the '66 trucks either. I may have heard it in the past, or may not have.
But yes, you should be able to compare the two bell housings not only by visual clues, but part numbers too, to see if there was a running change.

No worries about that now though. At least you got that one figured out. Now on to the next!

Paul
 
Top