• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

5.0 Engine Tick

kaw550

Bronco Guru
Joined
Jul 4, 2007
Messages
1,136
I have a ticking sound coming from around the #4 cylinder. The engine is a '92 5.0 with a roller cam. The heads were redone in the spring and the tick started right away.

I beleive I had torqued the rockers correctly.

I had installed manifolds with new gaskets when I installed the engine.

Any ideas?
 

badmuttstang

redneck grease monkey
Joined
Oct 25, 2009
Messages
2,807
Sounds odd but double check push rods. I got a really good deal on a 67 Fairlane GTA where the owner had motor work done and it had a tick as soon as he got it back. He was afraid to drive it and put it up for sell after shop couldn't find problem it was for sale for about a year because everyone who looked at was scared of the noise. So he dropped the price from $9000 to $2500 when I looked at it I told him I could fix it for about five bucks but he was done with it but wanted me to come by and show him after fixing it. Replaced one push rod and drove it back over in about a half hour. I could tell he was mad but happy to see it back on the road even gave me all the spare parts he had. Long story short just back back threw and look at the push rods and rocker bolts.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Good possibility its a push rod. Could also be a bad lifter, worn rocker arm or pushrod, or a valve that was not gorund quite right and now you have more clearance than it should have.
 

KyleQ

Bronco Guru
Joined
Apr 24, 2008
Messages
5,480
I damaged my engine, replaced the head, pushrods, rockers, and lifters and still has noise. Tons of oil psi, I've just been pounding on it - sound got quieter, but still there.
 

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
Cast exhaust manifolds don't have gaskets at least not from the factory. I pulled a head to replace a bent exhaust valve that failed to close and was hit by the piston. A valve click started when the head was re-installed. I needed a oversize push rod to fix it. The machine shop got it, so I'm not sure of the origin. The valve that clicked was not the replacement.
 

badmuttstang

redneck grease monkey
Joined
Oct 25, 2009
Messages
2,807
Cast iron manifolds should have a gasket installed but as far as tick I'd still look at push rods make sure no other push rods are bent or to loose. Just tighten down rockers and see if you can still move the push rod up and down should spin but not to freely. Then look to see if rockers are making contact with springs while rotating the motor.
 
OP
OP
kaw550

kaw550

Bronco Guru
Joined
Jul 4, 2007
Messages
1,136
I ended up putting the Bronco in storage. I just picked it up tonight. The tick didn't fix itself...

I will pull the valve cover tomorrow night. Would a leak between the exhaust manifold and exhaust tick?
 
OP
OP
kaw550

kaw550

Bronco Guru
Joined
Jul 4, 2007
Messages
1,136
I had a few minutes so I looked over the engine. No sign of an exhaust leak (no soot on the freshly painted block or gaskets).

So, I took off the valve cover. The last rocker on the passenger side was a little loose. The push rod would move up and down but the bolt was tight. I didn't have time to set the cylinder to TDC.

Should there be play in the push rod at any point in the engines rotation?

The others were tight enough to spin with no up and down movement.
 

bknbronco

Bronco Guru
Joined
Jan 17, 2011
Messages
4,388
Loc.
North Metro, MN
My rebuilt motor ticks too. I adjusted the hydrolic lifters 3 or 4 times but never any help. Not sure why mine would even tic with them lifters. I don't worry about it just hammer er down. I think that's how a 40 year old motor is supposed to sound. Im gona dump a quart of marvel mystery oil in er (as recommended by classic restoration magazine) and see what happens. If it goes away great, if not oh well.

There should only be minimal movement in the pushrod when the cylinder is at TDC. any other place and its pushing either on a exhast valve or a intake valve so it should be tight. You have to check with the engine hot and right when you turn it off.

You don't necessary have to have "that" cylinder at TDC. on my 289 I can adjust all 16 pushrods by only turning the motor to 3 different spots so it makes it much faster that way.
 

badmuttstang

redneck grease monkey
Joined
Oct 25, 2009
Messages
2,807
When heads were rubuilt did they replace valves if so make sure the stem ends are the same height but yes if lifters have bleed down then there might be some play but not a lot. Its a 92 so it should have pedestal rockers and they are just torqued down so no need to make sure its at top dead center as per ford spec's 17-23ft/lb's
 

KyleQ

Bronco Guru
Joined
Apr 24, 2008
Messages
5,480
Mine still makes noise, its seen max RPM plenty of times, no issues - plenty of oil pressure.
 

C Saporito

Full Member
Joined
Oct 18, 2007
Messages
259
Pull the coil wire and crank it over to pump up the lifters, then see if there is still play before the lifter drains, if so it's loose. If the noise is from the valve train geometry being off most likely the pushrod is rubbing in the pushrod casting hole in the head. Look for scuff marks on the pushrod, rocker arm tips not riding in the center of the valve stem would be another tip off. Start it up with the valve cover off, look and take listen.
 
OP
OP
kaw550

kaw550

Bronco Guru
Joined
Jul 4, 2007
Messages
1,136
I will give it a shot but I am going to have to cut the top off an old valve cover so I don't get oil everywhere....

I am also going to make sure it has the correct pushrods.

Is it possible to put a lightly longer pushrods in that one spot?
 

badmuttstang

redneck grease monkey
Joined
Oct 25, 2009
Messages
2,807
Yes but make sure there is no shims under the rocker arm first plus look at the ends of the valve stems make sure the height of the two next together look about the same height before doing that.
 

C Saporito

Full Member
Joined
Oct 18, 2007
Messages
259
Make sure something is different before you just install a longer pushrod! If you have a collapsed lifter you need to replace it, running it like a solid lifter can do much more damage!

If the machine shop installed a valve with a different stem height it's easy to diagnose and repair with a different length pushrod and/or shim. find out first what the difference is. Rotate the crank to TDC for that cylinder, pull the rockers off and use a straight edge across the stems.
 
OP
OP
kaw550

kaw550

Bronco Guru
Joined
Jul 4, 2007
Messages
1,136
I removed the intake and exhaust rocker. I found the one that was loose had a shorter pushrod. It measured just under 6 3/16 where the onen next to it was just under 6 1/4. About 1/16ths difference.

The engine is out of a 92 f150. Autozone has one listed as 6.250. Can I assume it is the same or do I need to go to a machine shop?
 
Top