• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

banjo bolt ?

horseman

Full Member
Joined
Sep 19, 2004
Messages
272
Got a couple questions. 77 front disk brakes
Does the hole in the banjo bolt line up with the hole in the end of the caliper flex line ?.

when I took the original hardware apart the copper crush washers were two different thickness. one aprox .063 thick and the other half that.

I put the new lines in and now have a leek. I didnt remember were each washer went so i guessed. I lined the hole in the banjo bolt and was bleeding the brakes when I noticed the leak. So i will head down to the parts house and get some new washers. But I am worried about over tightening the bolt to get the holes lined up. Thanks your help
 

DanHall

Full Member
Joined
Feb 18, 2013
Messages
234
Loc.
Pueblo, CO
Nope, no alignment necessary with the brake line. The leak was probably from trying to reuse the washers assuming everything else is in good shape.
 

mtp71174

Full Member
Joined
May 8, 2007
Messages
210
no alignment is correct and if you look at the banjo bolt the diameter of the bolt is smaller around near the hole and larger on each end. You need to replace both washer due to the fact they are copper and easily to compress to make tight seal thus once used
lose that trait. If you did use them again they may have worked if you torqued them to specs and in trying to align the holes may have been the cause of the leak.
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
IF, and only IF the washers haven't been scored or creased you can restore their sealing ability by annealing them. Copper work hardens very easily, just the act of tightening the bolts can do it. But if they are not beat up or haven't been in use for a long time then try this: make a simple wire holder that you can use to hold the washer and dangle it in front of a propane torch. Make the holder such that tilting it allows the washer to slide off. Grab a Red Dixie Cup and fill ~3/4 full of water. Light off propane torch and dangle washer at the tip of the flame. Walk it around a bit to evenly heat it and then let it slip off the holder into the cup. Repeat with any other copper washers that need it.

They'll come out of the water with an dark oxide film on them. Vinegar or Scotch-Brite will clean that off. Hose down with brake cleaner and try them again.

I used to do this a LOT with copper crush washers at a previous job.
 
OP
OP
H

horseman

Full Member
Joined
Sep 19, 2004
Messages
272
I used the old washers on driver side with no trouble. I have tried the old washers and they leaked went to part store and got new ones and I haven't and better luck with those. I tried heating the new ones as suggested above and it help kinda helped cuse it still leaking just not as bad.Any more suggestion ? . review 77 stock caliper with new flex hose and it leaking from the banjo bolt / crush washers Thanks
 

suthernboy

Sr. Member
Joined
Feb 16, 2010
Messages
422
Loc.
Greenville, NC
Can you tell which side of the block its leaking from? Block to caliper or block to bolt head? I assume you've made sure all your mating surfaces are clean and burr free, including the bottom side of the bolt head. If you can tell which side is leaking, try doubling up the washer & torque to 17 - 25 Ft. Lbs.. You've got nothing to lose.
 
OP
OP
H

horseman

Full Member
Joined
Sep 19, 2004
Messages
272
ya looks like its coming from the caliper /block. The caliper has a slight recess in it about the diameter of the washer and i've tried both a skinny and a thicker washer there. I think the thicker washer worked better ?. I will try the two washers and see it that helps.
 
Top