• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Battery Relocation Cable Runs

76bronc5.0

New Member
Joined
Jun 14, 2017
Messages
29
All,

I am in the process of relocating my battery to the driver side to make room for my cold air intake tube/filter on the passenger side. I wanted to get some insight from others on my current plan, which is as follows:

Positive Runs
1.) 1/0 cable from battery to ANL fuse (200-300 amp) to B+ stud on the starter solenoid.

2.) 4 gauge from 3G alternator to 150 amp circuit breaker to B+ stud on starter solenoid.

3.) 2 (or 4 gauge) from battery to additional ANL fuse to standalone power distribution junction. This will be used to provide a “clean” power feed for EFI (1993 5.0 HO EEC-IV) and CD box.

Negative Runs
1.) 1/0 cable from battery to engine block (3/8” threaded hole below alternator bracket on block)

2.) 4 gauge cable from battery to core support

3.) 4 gauge from firewall bulkhead to bellhousing bolt on back of block

4.) 1/0 cable from block to frame

5.) 4 gauge from firewall to block

6.) 4 gauge from battery to standalone ground distribution junction. This will be used to provide a “clean” ground path directly to battery for EFI and CD box.

Ultimately, I am trying to minimize the number of long cable runs from the battery while still retaining adequate circuit protection and providing a dedicated path for power and ground for the EFI and CD ignition box.

Has anyone used an ANL fuse for the main battery feed like I’m proposing? Most battery relocations I’ve seen typically relocate the starter solenoid close to the battery, so that it’s only hot while cranking, and then run a separate charge wire from the alternator back to the battery. I was trying to combine that in a single run but wasn’t sure how the fuse option would work during starting.

Lastly, how are others providing clean power and ground for their digital electronics? Can this be a clean distribution junction like I’m proposing or should both of those items have dedicated runs back to battery? Also, what about switched 12v power for the EFI and CD box? I currently have the pink ignition feed wire from my AAW classic update serving as my key on source (fed from main fuse panel, which currently receives power from the B+ terminal) but not sure if this needs to be repurposed to act as the trigger wire for a relay that then feeds “clean” switched power to the EFI and CD box? Looking forward to the discussion and thanks in advance.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
My thoughts...
Over gauged. Assuming you are using pure copper wire that is a lot of excess. If you are going CCA (Copper Clad Aluminum), it may not be big enough. CCA stuff looks appealing, looks all fancy and heavy duty, it is really garbage wire that can't flow current.

Stock cable gauge, even on the mustang donor, is much smaller. Usually 6 gauge. 4 gauge is typically the better cable to use. The starting current with a modern permanent magnet starter is about half of the old school ones as well.

The grounds look like a ground loop nightmare. More is not better. Huge doesn't fix bad.
Are you adding a winch that is grounded to the frame? Shy of an old school Bellvue winch they have a ground cable. Zero need for a massive ground to the frame. You need a good ground to the body and a good ground to the engine. Really, that's it. A bonding wire for the hood to body for RFI is a maybe, and that isn't even a battery connection. It is just a copper connection around a hinge since hinges are not always a solid ground path.

Most CD boxes and EFI have a streight power feed to the battery, no need to add relays. The turn on wire is just turning on a relay (in the harness for EFI, internal circuit for CD box).

More is not better. It is just excess. The original wiring (look at how wimple that mustang EEC-IV is. A lot of engineering went into making that work. Even with crazy police radios from when they were highway partol vehicles, all they got was a little bonding strap and that was just to help with the radios.

The 4-gauge for the alternator charge wire looks fine to me. Presume this is the 130A version of a 3G?
 
OP
OP
7

76bronc5.0

New Member
Joined
Jun 14, 2017
Messages
29
My thoughts...
Over gauged. Assuming you are using pure copper wire that is a lot of excess. If you are going CCA (Copper Clad Aluminum), it may not be big enough. CCA stuff looks appealing, looks all fancy and heavy duty, it is really garbage wire that can't flow current.

Stock cable gauge, even on the mustang donor, is much smaller. Usually 6 gauge. 4 gauge is typically the better cable to use. The starting current with a modern permanent magnet starter is about half of the old school ones as well.

The grounds look like a ground loop nightmare. More is not better. Huge doesn't fix bad.
Are you adding a winch that is grounded to the frame? Shy of an old school Bellvue winch they have a ground cable. Zero need for a massive ground to the frame. You need a good ground to the body and a good ground to the engine. Really, that's it. A bonding wire for the hood to body for RFI is a maybe, and that isn't even a battery connection. It is just a copper connection around a hinge since hinges are not always a solid ground path.

Most CD boxes and EFI have a streight power feed to the battery, no need to add relays. The turn on wire is just turning on a relay (in the harness for EFI, internal circuit for CD box).

More is not better. It is just excess. The original wiring (look at how wimple that mustang EEC-IV is. A lot of engineering went into making that work. Even with crazy police radios from when they were highway partol vehicles, all they got was a little bonding strap and that was just to help with the radios.

The 4-gauge for the alternator charge wire looks fine to me. Presume this is the 130A version of a 3G?
Thanks for the reply and feedback!

-All wire is stranded copper welding wire. I have an older style starter that came with the truck when I purchased it. I will
eventually replace it with a high torque mini version but I err’d to the side of caution with the larger gauge size to be safe.

-Thanks for the color on the grounds! Just for clarification, you’re suggesting I run a single heavy gauge wire from the battery to the engine block and then another smaller gauge wire from the battery to the body, correct? What about firewall bulkhead to block and frame to block? The bulkhead on the firewall was due to the bedliner that was applied to the interior of the cab, which made it difficult to get to a nice metal surface for grounding. I mention frame to block due to the rear components (fuel gauge, in tank electric fuel pump, etc.) being ground to the frame and needing a path as well. I am adding a Smittybilt Gen3 XRC winch with the solenoid mounted remotely due to the hidden winch style bumper that was recently installed but I will be connecting the positive and negative cables directly to battery.

-On the EFI and CD box, would you recommend running power and ground straight to battery for both items individually? That makes sense on the switched 12v driving an internal relay, which is what I figured.

-correct on the 130 amp 3G alternator.

What about the ANL fuse for the battery feed/charge wire? Or would you recommend a different route? Thanks again!
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
I made an assumption of 4 foot length for the bat + cable to the starter length and used the top end of your ANL fuse range for the amperage. Then using these two pages:
I calculated that for 3% max voltage drop (I use that std. for all calcs) and the formula on the second link I came up with needing a Circ Mil Area of 35,833
6 ga. (Circ Mil = 26,600) is too small, so 4 ga. (Circ Mil = 42,000) is the gauge recommended. For some overkill I might consider going to 2 ga. at the very most. Doubling the length and assuming 300 amps still only puts you into a 1 ga. cable.
It is fortunately rare that an alternator runs at max output for very long. If it is doing that it won't live very long. The newer alternator designs are better, but the heat generated by that level of output will kill it reasonably fast.

I've never felt the need to fuse the starter, but I know that some do. The in-rush current can be 100% more than the steady-state current.
Most of those PMGR starters are ~1.5kW, so maybe as much as 150 amps steady-state demand depending on what the load pulls the battery voltage down to. IF the old school type starters can pull double that, then a large enough fuse becomes problematic to find and package.

A diagram of the grounds should look like a tree with the battery as the root ball. They can branch out from the root ball, but branches never connect with other branches. I would suggest battery to engine (4ga.), battery to body (8-10ga.), and body to frame (12ga.). That's it. At very high currents (starter, winch) the frame isn't a good conductor, but for normal current loads it works just fine. A battery in the trunk of a passenger car should get it's own ground cable to the engine block or hard hot starts are the likely result.
If you notice, the formula for determining the wire or cable size is only interested in the amperage and the length, the voltage doesn't matter to that calculation. Make the ground wires/cables the same size as the hots.
As @jamesroney pointed out to me not all that long ago, the only circuit grounded to the frame is the fuel level sender. I'll assume that an in-tank fuel pump will share that ground, but that's it.

MSDs want direct to the battery connections for their main power and ground wires. No relay since they switch on/off internally and adding a relay there is just another failure mode. Perhaps a fuse or breaker at the battery if you're really worried about the power wire shorting somewhere between the battery and the box.

RFI bonding may look like grounding wires (like body to hood), but they are not. For that purpose I'll suggest using flat braided cable instead of insulated wire. High frequency electric energy 'likes' it batter than an insulated wire or cable.
 

Steve83

Bronco Guru
Joined
Jul 16, 2003
Messages
9,360
Loc.
Memphis, TN, USA, Earth, Milky Way
1/0 cable from battery to ANL fuse (200-300 amp) to B+ stud on the starter solenoid.
1/0 cable from battery to engine block...
0ga wire is way too big - the most current that can possibly ever flow is the batteries' CA rating (hot - not CCA). It would take at least 2 large cranking batteries to necessitate 0ga. There shouldn't be any circuit protection between the battery & starter. The block ground only needs to be heavy enough for the starter. Everything else that passes through it is lower than the starter's draw which is ~140A under normal conditions.
4 gauge from 3G alternator to 150 amp circuit breaker to B+ stud on starter solenoid.
Way too big, and 150A is undersized for a 130A alternator, and FAR undersized for 4ga.
2 (or 4 gauge) from battery to...power distribution junction.
Unless you're planning on putting 500+A of electrical loads through this junction, that's too big. The corresponding wire on a 90s PowerStroke is ~6~8ga, which serves all the EEC, sensors, IDM, radio, A/C, lights, ABS, gauges, horn...
4 gauge cable from battery to core support
Unless you're grounding 300+A of loads to the body, that's too big.
4 gauge from firewall bulkhead to bellhousing bolt on back of block
Why? The normal block ground grounds the whole block. Pick one, and do it right. I'd pick the one that's easier to check & maintain occasionally.
1/0 cable from block to frame
What are you going to ground to the frame? Again: the max is what the battery (or batteries) can push without exploding, which is the sum of the CA ratings for each one.
4 gauge from firewall to block
The firewall is welded to the inner fenders which is welded to the core support - pick one. More giant wires all over the place are just expensive & useless weight.
...I am trying to minimize the number of long cable runs from the battery...
Long cable runs aren't problems, if they're properly sized & protected. And for the negative, a single long heavy wire (4ga is plenty) from the battery to the rear bumper is a smart move, since every "ground" wire could be tied into it so that nothing actually relies on the body or frame for its electrical circuit. The body & frame can & should still be grounds and solidly connected to the B-, but there's no advantage to running current through steel instead of Copper.
...a dedicated path for power and ground for the EFI and CD ignition box.
The easiest, safest, most cost-effective way is to mimic newer vehicles.
...wasn’t sure how the fuse option would work during starting.
It would blow almost every time.
...how are others providing clean power and ground for their digital electronics?
They're not. Modern electronics (especially digital) are built to tolerate "noise" in the 12V power supply. Digital is naturally less-affected by analog power supply fluctuations.
...what about switched 12v power for the EFI and CD box?
The more connections & switch contacts & fuse terminals you have in any circuit, the more resistance & problems you can expect. If the wire is sized properly, a long simple high-current circuit is far better than a short complicated one. For low-current circuits, it becomes irrelevant pretty quickly, other than for reliability/maintenance/troubleshooting.
...“clean” switched power...
Think about where this "noise" is coming from, and address THAT instead of overcomplicating & overspending on the harness. Ford has published quite a bit of advice about wiring modifications, and I've collected some of it & some of my own advice (based on 4+decades of all kinds of electrical work including at a Ford dealership) on this page:

(click this text)
 
OP
OP
7

76bronc5.0

New Member
Joined
Jun 14, 2017
Messages
29
All,

Thanks for the replies and insight! I do want to clarify that I knew these sizes were likely overkill but I had extra cable in these sizes from past projects and figured it as cheap insurance if nothing else.

Additionally, I wanted to add some context behind the intent of the post. The bronco was gifted to me by my wife, lucky guy I know, back in 2017 and already had the 5.0 HO installed with a standalone Painless EFI harness. The previous owner opted to keep the factory Bronco wiring harness and had a plethora of Scotchloks/Add-a-circuit connections for additional accessories, which led to a lot of electrical gremlins. That being said, I decided to replace the factory harness with an AAW Classic Update kit back in 2018. I also opted to add a WetSounds sound bar and Alpine head unit during the rewire as well. Overall, the truck has ran great over the past 7-8 years but I’ve always had a little alternator noise through the sound bar that I’ve never been able to rectify. Fast forward to this year, I had the truck repainted and replaced the original hood with a fiberglass cowl version, so I could add the required intake spacer to run the bronco script valve covers. As part of that effort, I wanted to add the CAI to draw fresh air from the passenger side battery area, which required moving the battery to the driver’s side in order to accomplish. With the relocation, it gave me an opportunity to also address the alternator hum issue as well an make sure that other components (EFI) weren’t being adversely being impacted.

Long story short, the intent of the post was to have those more knowledgeable than me cross check my cable run locations/thought process and insure I still had adequate circuit protection on the new cable runs. I’ve heard horror stories of voltage sensitivities with new EFI systems due to the lack of separation between dirty and clean power, which made me concerned that if I had issues with the soundbar that it was likely impacting other devices as well.

So my hope is that someone smarter than me can help me identify what was causing the original issue (likely a ground loop based on what others have mentioned here) and guide me on the new cable runs so that I don’t make the same mistake.

Here are the cable runs I had following the 2018 rewire:

Old Positive Runs
  1. Alt to 150amp CB to Battery
  2. Battery to B+ Terminal on starter relay
  3. B+ terminal on starter relay fed power to main AAW fuse block and auxiliary fuse block.
    • Aux fuse block used to provide high current power to relays (electric fans, light bar, etc.)
    • Aux fuse block also provided fused power for sound bar.
Old Negative Runs
  1. Battery to block
  2. Battery to frame (welded stud on frame rail)
  3. Firewall bulkhead to frame (shared same welded stud)
    • Bulkhead added to terminate all dash/interior grounds and ensure there was a clean path to ground via the frame to battery connection.
    • No direct body ground other than through spot welds between panels (likely my problem)
    • Also had to run dedicated ground from alt to block as the ground path through the mounting bracket failed me after a year or so.
Based on the replies here is what I was planning with the battery relocation:

New Positive Runs
  1. Alt to CB (increase to 175-200 amp) to B+ terminal on starter relay
  2. Battery to B+ terminal on starter relay
    • Serves as both starter power feed and charge wire
    • No fuse per comments above
  3. B+ terminal will continue to feed both main and aux fuse blocks (including EFI)
New Negative Runs
  1. Battery to block
  2. Battery to body (core support)
  3. Firewall bulkhead (dash/interior ground point) to block
  4. Frame to body
    • Welded stud on frame rail to core support
Thoughts on the new cable runs? Am I creating potential ground loops? Should the EFI and CD box have power and ground directly attached to the battery post (the EFI currently gets power from the main fuse block and grounds through the firewall bulkhead - TFI grounds through Let me know thoughts on what was likely causing the alternator whine through the sound bar on my original configuration.
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
I take it that by "CB" that you mean a circuit breaker. I tend to prefer fuses or fusible links for circuits where there may be high surge currents. Fuses and fusible links are slower to pop than are circuit breakers. To use a circuit breaker you end up needing to run one with a lot higher rating than the actual circuit surge amperage. There is such a thing as a "slow-blow" circuit breaker, but they're not always easy to find.
I tend to follow the OEM lead and have yet to put a fuse or a breaker in the alt charge cable on any of my past projects.

I would eliminate either the battery to body ground or the firewall to block ground. Both together create a ground loop. Unless I'm misunderstanding what you mean by "firewall bulkhead."
When I need a frame ground I prefer to drill and tap a hole in the side of the frame if I can't use an existing hole and possibly bolt, rather than weld on a stud. On my FSB the OEM grounding goes to a bolt on the frame and then on to the engine block. I've grounded both the winch and the second battery to that same bolt.

Stereos, particularly amplifiers, prefer to pull direct from a battery because the battery itself acts as a pretty good noise filter. Same it true for ham radios & similar.
 

Steve83

Bronco Guru
Joined
Jul 16, 2003
Messages
9,360
Loc.
Memphis, TN, USA, Earth, Milky Way
...make sure that other components (EFI) weren’t being adversely being impacted.
What symptoms have you noticed from the EFI system?
...the original issue (likely a ground loop...
That's not likely at all. A ground loop is actually a pretty complicated error that only affects very complicated circuits. It's nearly impossible to create a real ground loop on a 12VDC vehicle with only 1 battery connected to 1 alternator. 2 wires going to ground is NOT a ground loop, and neither is a wire grounded at both ends - it's MUCH more complex, so don't worry about it.

Hum in the sound system that follows the engine RPM is most likely caused by poor battery terminals, a failing battery, high resistance in the amplifier circuit, ignition system problems, or a low-quality amp (lacking normal filtering). Does the ignition system include a capacitor on the coil positive wire? If not, consider adding this one:

(click this text)


You could also try a filter capacitor across the amp (sound bar) power wires. That will mask resistance (poor connections) in the amp positive & negative circuits.
Firewall bulkhead to frame (shared same welded stud)
I'd pull those terminals off that stud & clean them thoroughly (wire brush) then apply electrical grease (NOT dielectric, or conductive, or anti-seize, or thermal, or chassis).
...spot welds between panels (likely my problem)
Not likely, but if you think so, simply turn on every electrical load you can with the engine running, and measure voltage across the spot-welded seam. It should be the same as touching the meter probes to each other (~0.000 VDC). If it's above ~0.1 VDC, there might be a problem.
Also had to run dedicated ground from alt to block as the ground path through the mounting bracket failed me after a year or so.
That's a BIG problem, and it could be the root of a LOT of your electrical problems. The alternator case ground is arguably the most-important on any vehicle, so you should resolve that ASAP. Un-mount the alternator & its bracketry, and polish every face of every contact surface from the alt case to the head & block. It's not necessary to disassemble the alt, unless it's visibly corroded in the middle.

(click this text)

B+ terminal will continue to feed both main and aux fuse blocks
Accessory feeds should be connected either to the starter relay's B+ terminal, or to the fuse block(s). Not directly to the battery + terminal.
Am I creating potential ground loops?
No.
...power and ground directly attached to the battery post...<?>
No. The battery is generally a BAD place to connect things, because of the acid. So since you HAVE to connect some things there, they should only be very thick wires that can withstand some corrosion, and they should be soldered into the terminal clamps so there are fewer pockets for acid to hide & work.

(click this text)
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
Ground loops don't care what the system voltage is. A difference in potential is a difference in potential and will cause problems.
Ground loops can also act as an antenna and inject noise into a circuit or circuits. It's this last part that isn't, apparently, understood by the poster above. I've experienced it in a professional setting with available electrical engineering knowledge far exceeding any that I've seen posted here (including my own), no amount of keyboard warrioring is going to convince me otherwise.
 
OP
OP
7

76bronc5.0

New Member
Joined
Jun 14, 2017
Messages
29
I take it that by "CB" that you mean a circuit breaker. I tend to prefer fuses or fusible links for circuits where there may be high surge currents. Fuses and fusible links are slower to pop than are circuit breakers. To use a circuit breaker you end up needing to run one with a lot higher rating than the actual circuit surge amperage. There is such a thing as a "slow-blow" circuit breaker, but they're not always easy to find.
I tend to follow the OEM lead and have yet to put a fuse or a breaker in the alt charge cable on any of my past projects.

I would eliminate either the battery to body ground or the firewall to block ground. Both together create a ground loop. Unless I'm misunderstanding what you mean by "firewall bulkhead."
When I need a frame ground I prefer to drill and tap a hole in the side of the frame if I can't use an existing hole and possibly bolt, rather than weld on a stud. On my FSB the OEM grounding goes to a bolt on the frame and then on to the engine block. I've grounded both the winch and the second battery to that same bolt.

Stereos, particularly amplifiers, prefer to pull direct from a battery because the battery itself acts as a pretty good noise filter. Same it true for ham radios & similar.
Thanks for the reply.

Yes, CB is referring to a circuit breaker.

Can you elaborate on how those two create a ground loop? I have two independent paths back to the battery negative terminal. The first is battery to block to firewall bulkhead. The second is battery to core support (body) to frame. Would the ground loop be created due to the fact that the core support is interconnected to the firewall via bracing? Just to elaborate, the firewall bulkhead is essentially an insulated stud that is threaded on both sides, which allows me to terminate all interior grounds on one end and then run a single heavier gauge wire from the other end to either battery, frame, or body. Basically provides a single, equal potential path back to ground, so it circumvents the connection back to battery via the body, which is 50 year old sheet

That’s a good point on the tapped hole frame ground vs. welded stud option. I’m guessing the weld could potentially create additional resistance as opposed to the tapped hole?
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
Two independent paths to ground from the same consumer or group of consumers is a group loop. Two wires or cables that run exclusively from the same bolt or connector to another same bolt or connector are not. Ideally such paired grounding wires would be twisted together, but that's heading towards being the belt and suspenders solution.

What you're calling a bulkhead I call an isolated stud. By "bulkhead" it sounded to me like the firewall itself was in the circuit. Since it is not because of the pass-thru being an isolated stud then my concerns about a ground loop don't apply.

Welds in a circuit can be tricky. Usually at low current they have very little resistance and at high current can have much higher than expected resistance, most of, but not all of the time. As I'm unclear on where that change occurs, if it does, I think it best to just avoid them.
 
OP
OP
7

76bronc5.0

New Member
Joined
Jun 14, 2017
Messages
29
Two independent paths to ground from the same consumer or group of consumers is a group loop. Two wires or cables that run exclusively from the same bolt or connector to another same bolt or connector are not. Ideally such paired grounding wires would be twisted together, but that's heading towards being the belt and suspenders solution.

What you're calling a bulkhead I call an isolated stud. By "bulkhead" it sounded to me like the firewall itself was in the circuit. Since it is not because of the pass-thru being an isolated stud then my concerns about a ground loop don't apply.

Welds in a circuit can be tricky. Usually at low current they have very little resistance and at high current can have much higher than expected resistance, most of, but not all of the time. As I'm unclear on where that change occurs, if it does, I think it best to just avoid them.
Thanks for the explanation. That makes perfect sense and confirms I was thinking about it correctly. Here’s a link to the exact bulkhead connector I have for visual reference:

https://www.moroso.com/thru-panel-b...NYesbVESRB75CM_L8jcLtRkCeAA4wfLCBCYsacD6DW4zZ
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
I used two of those on the Valiant when I moved the battery to the trunk. Being a unit body running the battery cables under the car would have left them very exposed to road debris. I ran them inside instead and used two of those isolated feed-thru studs to pass power and ground thru the firewall.
 

Steve83

Bronco Guru
Joined
Jul 16, 2003
Messages
9,360
Loc.
Memphis, TN, USA, Earth, Milky Way
I have two independent paths back to the battery negative terminal. The first is battery to block to firewall bulkhead. The second is battery to core support (body) to frame.
Those aren't independent, and they're not a ground loop. That's called a "redundant" ground from the battery to the body (at the core support & firewall). That cannot cause any problem, unless they're substantially different sizes, and the larger one becomes disconnected somehow during a high current draw (like cranking or winching). In that case, the smaller redundant ground becomes either a heating element, a filament (like in a bulb), or a fusible link (when it burns through).
...stud that is threaded on both sides, which allows me to terminate all interior grounds on one end and then run a single heavier gauge wire from the other end to either battery, frame, or body.
That's a "pass-through" stud. But because it's passing "ground" wires through a grounded part of the body, it doesn't need to be insulated - it, all the wires connected to both sides of it, and the body, should always be at the same voltage (potential).
I’m guessing the weld could potentially create additional resistance as opposed to the tapped hole?
No, the threads are more likely to have resistance than the solidified weld (which is essentially the same as the hot steel that was rolled into sheets to make the body panels & frame).
Ground loops don't care what the system voltage is.
Yes, the voltage matters, because the lower the voltage, the less-likely there will be a ground loop. A ground loop is much more likely in a high-voltage AC circuit.
A difference in potential is a difference in potential and will cause problems.
A difference in potential is the only reason that electricity flows anywhere. The battery has a ~12V (nominal) difference in potential, and that's how it's supposed to work - no problem. So your blanket assertions are getting really crazy.
Two independent paths to ground from the same consumer or group of consumers is a group loop.
No, that's not even close. And if they run to & from the same things, then they can never be independent.
Two wires or cables that run exclusively from the same bolt or connector to another same bolt or connector are not.
That's correct - they're NOT a ground loop, which is almost physically impossible on an antique vehicle because of the low DC voltage & dispersed low-current grounding points.
...no amount of keyboard warrioring is going to convince me otherwise.
Well, that makes you the keyboardEST warrior ever. ;) (y)
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
I know better, and occasionally I forget. Never battle with this forum's longest lasting troll. Why he's still here when every other Ford forum has booted him off I do not know.
 

Steve83

Bronco Guru
Joined
Jul 16, 2003
Messages
9,360
Loc.
Memphis, TN, USA, Earth, Milky Way
A troll is someone who takes an on-topic discussion and turns it into a personal attack, which I don't do. That's your specialty - usually when you realize you've posted some indefensible nonsense. I guess you think Wikipedia & every other article that explains what ground loops really are is also written by trolls. :ROFLMAO:
 
Top