• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

bending brake line

bgs26

Sr. Member
Joined
Nov 30, 2005
Messages
493
Loc.
Eunice, LA
I am doing my front disc conversion this week. The fittings on the old lines are sort of rounded and they are old so I want to change them along with the lines. How complicated is it to bend your own brake line vs. having some made. I will need a few custom bends. Any help is appreciated. Thanks!
 

Bucky

Full Member
Joined
Aug 26, 2007
Messages
250
Loc.
New Bern, NC
It's not too hard, Stainless can be a pain! I bought the cheap Autozone bender and they did OK! I bought a bunch of my lines at Napa.

Good Luck!!!
 

70_Steve

Old Guy
Joined
Dec 13, 2002
Messages
8,317
what did you buy...a roll of so many feet and cut and bend as needed?
Napa will not carry stainless tubing. They carry various lengths of hard steel tubing, premade to different lengths with the ends pre-flared. I bought lengths that were longer than what I needed, cut to length, then double-flared the end I cut. I got away with not using a tubing bender. Most bends I bent by hand, holding the tubing in each hand and bending around my thumbs (if you can picture that). I did make a couple relatively tight bends, and just bent the tubing around something that had the same radius as the bend I needed. The 3/16" tubing is hard to kink.

You would not want to use the soft tubing that would come in a roll.
 
OP
OP
bgs26

bgs26

Sr. Member
Joined
Nov 30, 2005
Messages
493
Loc.
Eunice, LA
Thanks. I just looked on the napa sight and I see what you mean. I guess tomorrow I will see what I need and make a trip to NAPA.
 

TDS-03

Jr. Member
Joined
May 21, 2007
Messages
97
Loc.
Monterey Park, CA
I redid my front lines after swapping in a D44. Removed the old lines (that got crushed) and used them as a template.

I bought a roll of about 20 feet and several fittings. Also purchased, cheapo bender and flaring tools form Harbor Freight. Bender is fine, flare tool will be shot with much more use, but it got the job done.

Be sure to clamp the flare tool down with a vise, much easier.
 
OP
OP
bgs26

bgs26

Sr. Member
Joined
Nov 30, 2005
Messages
493
Loc.
Eunice, LA
What about flaring...do you all use double flared ends. I was reading another thread earlier and one guy said all he has ever used are single flares. Anyone with experience there?
 

68 Broncoholic

Bronco Guru
Joined
May 16, 2005
Messages
1,742
Loc.
WA
To bend, use anything round. I use a screwdriver handle. I looped several winds around the handle to use up the excess I had at the master cyl. Doing this also allowed for movement in the line when not using rubber or braded lines.
 

fordtrucks4ever

Bronco Guru
Joined
Oct 8, 2006
Messages
1,280
Loc.
DFW
What about flaring...do you all use double flared ends. I was reading another thread earlier and one guy said all he has ever used are single flares. Anyone with experience there?

You will get a lot of different opinions. Dont do the single flare. The double flare is nothing more than rolling the cut edge inside before flaring the tubing. The single will split and does not seal well. You are tightening steel to steel on some pieces. A single flare works well on softer tubing like copper and brass. Also under less pressure on most applications. Most flaring kits will do double flares just fine. The cheap HF suprisingly does a really good job. Practice a few times before flaring your finish pieces. Make sure when you feed the tool that its centered. The HF flaring kits are less than $10. I think I paid 5 or 6 bucks a few years ago. I have replaced the line vice with a better brand, but still use rest of the HF components when bending both types of automotive flares.
 

Bucky

Full Member
Joined
Aug 26, 2007
Messages
250
Loc.
New Bern, NC
If you use stainless, you need a hydraulic tool to Flare them. I would just use the steel lines and a double flare tool.
 
OP
OP
bgs26

bgs26

Sr. Member
Joined
Nov 30, 2005
Messages
493
Loc.
Eunice, LA
Thanks guys. I have a flare tool but no die with it. Does Napa or sell any dies for this?
 

TJK74

Bronco Guru
Joined
Feb 21, 2003
Messages
3,154
Loc.
Newark CA
They also sell those coiled spring wrap benders that are great for doing hand bend. wrapped a few coil rounds around a mag light to get the bends to the MC
 

Attachments

  • Brake lines.jpg
    Brake lines.jpg
    125.8 KB · Views: 143

ponch0v

Sr. Member
Joined
Nov 2, 2001
Messages
671
I use tubing from McMaster-Carr:

p/n 5176K22
Roll-Formed (Bundyweld) Corrosion Resistant Carbon Steel Tubing 3/16" OD, .132" ID, .028" Wall, 25' Coil, SAE Spec
$13.72 Each


Also use these benders from Eastwood:

http://www.eastwoodco.com/shopping/...mType=PRODUCT&RS=1&itemID=10826&keyword=49074


Sears has double flare kits

I have also found that the pre made tubes you get from the parts houses are a few thousands under sized so they slip in the fraring tool. The tubing from Mc-C is the correct OD and works in the flaring tool every time.
 

BwoncoHowie

C-4 Wizard
Joined
Nov 11, 2002
Messages
3,571
What about flaring...do you all use double flared ends. I was reading another thread earlier and one guy said all he has ever used are single flares. Anyone with experience there?

Absolutely use a double flare, they will resist cracking at the flare!
Auto manufacturers do this on brakes, fuel, and transmission lines for a reason.

...Plummers dont usually see the need for double flares.
 

BwoncoHowie

C-4 Wizard
Joined
Nov 11, 2002
Messages
3,571
They also sell those coiled spring wrap benders that are great for doing hand bend. wrapped a few coil rounds around a mag light to get the bends to the MC
Atta Boy! Thats ingenuity for you! Think I'll try that when I get ready to do my MC lines. :) ;) :cool:
 

TJK74

Bronco Guru
Joined
Feb 21, 2003
Messages
3,154
Loc.
Newark CA
Thanks;D
Using the maglight as a bending die was quite easy and let me easily wrap a few coils that gave a good amount of flexibility to the hard lines. Since that pic was taken I have up graded to disc brakes and the f-250 camper special MC which has the lines entering the MC on the same side but slightly a little more forward and upward. With the coils in the line I was easily able to hook up the same lines to the new MC with no problem;D
 
Top