• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Bent header removal suggestions

MitchE

New Member
Joined
Oct 25, 2020
Messages
43
Hope all of you are safe and well.
Third month with my 75 and getting more and more intimate with the engine tracking down low compression and misfire issues. Thinking of pulling the heads off to inspect the valves. Air coming out exhaust during leak down. Need advice on best way to get at the header bolts as the manifold is bent and pressed up against the left hand bolts. I won't be able to get a socket around the head.
Not sure how to bend it back to straighten out the pipes.
Or should I cut em off and get new headers they are a little rusty at connection.

'75 sport with 302 and 351W heads.

Thanks for all the help
 

Braifab

New Member
Joined
Nov 22, 2017
Messages
38
Loc.
Fort Smith, Arkansas
Well you mention both a "header" and "manifold" but being it is bent, I'm assuming it is indeed a "tube header" and not a "cast iron manifold". I use an old extension for its blunt end to dent the tube inward away from the bolt head. You can always knock the dent back out afterward. As for the rust, if you see it on the outside then rest assured it is much worse on the inside due to condensation from heat cycles. Unless of course it is ceramic coated. I have been working on new headers for a while, with apologies to nvrstuk for the delay, and hope to have a couple of different versions for folks to choose from. I'll try and attach a couple of pics, my computer skills being what they are and all.:)
LS Header.jpg
 

56f100bbw

Contributor
Bronco Guru
Joined
Feb 3, 2008
Messages
2,406
Loc.
Tucson / lakeside AZ
I have long tube headers and 3/8 bolts and a socket won’t work have to use a closed end wrench super tight did a header gasket a few days ago took forever ac comp in the way not a fun job you got coming
 
OP
OP
MitchE

MitchE

New Member
Joined
Oct 25, 2020
Messages
43
Thanks guys.
Yes I meant headers.
Guess I'm Going gorilla!
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Are yours just regular bolts then Mitch? A lot of us have taken to using small-headed hex bolts, or 12-point bolts, or hex bolts with the female holes that allow you to use an Allen wrench on them.

If yours are regular hex bolts, you might consider one of the other styles, or even locking ones like Stage-8 or one of the other types of locking fasteners. Two birds, so to speak.
Easier to get a wrench on, and much less likely to loosen up over time.

Paul
Paul
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
Headers can be tricky.
I typically use end wrenches, sockets, and crows feet to torque them up.
But that's what is needed. Those bolts need to be torqued properly. Otherwise you'll be blaming the headers for loose bolts and leaks.
I torque them. Three times with several heat-cool cycles in between. After that, they stay tight. Mine haven't been touched in eight years now. And I just use the standard "non locking" header bolts.
 

gr8scott

Contributor
Bronco Guru
Joined
Jul 1, 2011
Messages
1,890
These gaskets are worth the money, especially when plain old Felpros were the same price.

https://www.wildhorses4x4.com/product/Remflex-Graphite-Header-Gaskets/bronco_headers

Description
• Seals Warped Flanges: Remflex exhaust gaskets come in a standard 1/8-inch thickness and are designed to crush 50%. This allows them to fill gaps in the flange surface up to 1/16-inch!

• Won't Burn Out: 100% flexible graphite construction means Remflex gaskets are good for up to 3,000 degrees F—far exceeding that of any vehicle's exhaust system temperature! 50% Crush

• No Re-Torquing Necessary: Remflex exhaust gaskets rebound 30%, creating an optimum seal that eliminates the need to re-torque!

Remflex's unique flexible graphite material has been proven for more than 30 years in industrial applications, where temperatures routinely exceed 2,000 degrees—day after day, week after week, year after year. Now, we're bringing this technology to enthusiasts of all kinds to eliminate exhaust leaks for good! Whether you have an old pick-up that needs a manifold gasket, or a race car with custom-built headers, you can be assured that Remflex exhaust gaskets will work properly the first time, every time.
 

Jfryjfry

Sr. Member
Joined
Aug 28, 2017
Messages
503
Unless it got bent after installation, they were installed like that which means they can be removed without damaging them.

You’ll likely have to use an open-ended wrench to get that one/those out. Remove the ones you can, but make sure to leave at least one other in while you get the “captured” one(s) out. You will turn the bolt(s) as you pull the header away from the head. It’s typically the rearward bolt on the front or maybe middle cylinders.

And I would highly recommend percy’s header gaskets. They are about $45 but thick and conforming. Only had them about 1k miles on our fresh rebuild but so far no leaks and no loosening of the header bolts.
 

JWMcCrary

Contributor
Bronco Guru
Joined
Oct 14, 2004
Messages
5,001
And I would highly recommend percy’s header gaskets. They are about $45 but thick and conforming. Only had them about 1k miles on our fresh rebuild but so far no leaks and no loosening of the header bolts.

That's the best there is in my opinion. I just pulled these off my 351w, been on there since 2013. Installed tight and never had to touch the header bolts afterwards. Aluminum heads so the header bolts had anti seize but never had a loose bolt or a leak. Will be going back with the same.
 

Attachments

  • Percy's header gaskets (2).jpg
    Percy's header gaskets (2).jpg
    124.8 KB · Views: 55

gnpenning

Contributor
Bronco Slave
Joined
Dec 26, 2011
Messages
2,601
Loc.
I have more questions than answers.
If you have air coming out the exhaust while doing cylinder leakage tests then yes, you need to pull the heads for some refresh work. Make sure you don't have leakage going on any place else.

Good time for a rebuild or to put in whatever upgraded motor you have been hoping for.
 
OP
OP
MitchE

MitchE

New Member
Joined
Oct 25, 2020
Messages
43
You guys have been great thanks.
And yes I have three leaky cylinders not making compression. Two are exhaust...as the blue covid gloves I put on the pipes were flipping me off. The third I'll need to recheck. I'm shopping for a nice crate. Thinking 347 striker. Still need to pull the heads off.
Funny thing is she is not running that bad just a dog on power.
I'll get those gaskets and try again with open end and blaster.
 

bigmuddy

Contributor
Bronco Guru
Joined
Dec 28, 2004
Messages
8,071
Loc.
Marthasville Missouri
That's the best there is in my opinion. I just pulled these off my 351w, been on there since 2013. Installed tight and never had to touch the header bolts afterwards. Aluminum heads so the header bolts had anti seize but never had a loose bolt or a leak. Will be going back with the same.


I will 3rd that recommendation. Had them on and off my prior engines many times and finally decided to replace them on the new 351w.
 
Top