• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

blown head gasket question. Engine guru's

phred

Contributor
Bronco Guru
Joined
Aug 25, 2006
Messages
3,608
Loc.
Earth
Just got a call from a friend. Blown head gasket I'm 99% sure as it was puffing water and steam out of the radiator overflow. Temp was 260 plus. It ran like this at idle for about 10min. What should I look for when I pull the heads besides the obvious blow out. Do you think the bearings could have been hurt?
Oh and it is in his EB.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Look for cracks in the heads or block usually wont happen if not overheated very bad. Bearings shouldnt be hurt unless a lot of water got into the oil and it was run a long time. Oil pressure should tell you some. if its lower with fresh clean oil than it was then I'd suspect the bearings got wiped out. but if oil pressure is normal then it should be fine.
might be a good idea to get the heads rebuilt and checked out real good.
 

Revelation

Bronco Guru
Joined
Oct 9, 2004
Messages
4,825
Water and steam out the radiator overflow would indicate overheating, Blown headgasket would have water in the oil or water and steam out the exhaust.
UNLESS remove radiator cap and see if you can feel it puffing with the RPM.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Not always. I've blown a few head gaskets one on a 302 and have yet to have one put water in the oil. Most of the time it leaks into a cylinder or into the cooling system. causing the overheating if it goes into the cylinder then yes you get steam out the exhuast but if its going into the cooling system you get bubbles and steam in the radiator.
 
OP
OP
phred

phred

Contributor
Bronco Guru
Joined
Aug 25, 2006
Messages
3,608
Loc.
Earth
According to the owner it was puffing from the overflow with the rpms and steam from the exhaust.
 

gearida

Bronco Guru
Joined
Jun 8, 2007
Messages
1,428
Loc.
Newburgh, IN
Compression check, look for coolant around the head, and pull spark plugs looking for a whiter than normal electrode. When doing the compression check remove all spark plugs, you may just spin it over and see spit of coolant coming out a spark plug hole. Normally the piston will be cleaner, if you can see into the cylinder too. By putting a coolant pressure tester on the radiator and adding pressure you will also see it bleed off, if you have a head gasket problem.
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
On my 74 Bronco I lost the cylinder head gaskit and the symptoms were engine running hot and would only boil over after the engine was shut off. Cylinder preasure was leaking into the water jacket and no leakage of coolant into the oil or exhaust. Upon dissassembly the fire ring was rusted through and leaking compression into one of the small holes on the block face.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
Another thing to look at the radiator. Not as a cause of the problem but a victim of it. If you dump a lot of cylinder pressure into the cooling system faster then the rad cap can vent it there is a possibility that the system can overpressurize, tubes can distort, collapse the fins, blocking airflow and generally ceasing to be an effective radiator. All without springing a leak.
 
Top