• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Bored .010, Decked .020 - GT40 Compression?

GrillMaster

Contributor
Bronco Guru
Joined
Jun 5, 2008
Messages
2,505
My 92 351W block was bored 10 thousandths of an inch over stock and decked 20 thousandths of an inch. What compression ratio am I looking at with a set of GT40 heads? Running flat top pistons. ;D
 
OP
OP
GrillMaster

GrillMaster

Contributor
Bronco Guru
Joined
Jun 5, 2008
Messages
2,505
think GT40 heads are 60-64cc, Not sure what compressed gasket thickness is.
 

DJs74

Bronco Guru
Joined
Apr 1, 2014
Messages
1,135
My 92 351W block was bored 10 thousandths of an inch over stock and decked 20 thousandths of an inch. What compression ratio am I looking at with a set of GT40 heads? Running flat top pistons. ;D


Any chance those numbers are reversed? 0.020" off the block seems like a lot - unless maybe the idea was to purposely raise the compression ratio.

If 0.020" is real, just proceed with caution on piston to valve clearances and give careful consideration to what head gaskets are needed for clearances (which will also effect the compression)



Take care,

DJs74
 
OP
OP
GrillMaster

GrillMaster

Contributor
Bronco Guru
Joined
Jun 5, 2008
Messages
2,505
-.020 is correct. Got it done 16 years ago... I dont remember why they did it. About to get the cosmolene removed this weekend so I can mock it up.
 

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
All depends on how deep in the hole the pistons are. Then you have the head gasket thickness.

You will also need to know for sure the CC on the heads before you can get a accurate number for compression.

Tim
 

74strokerbronco

Full Member
Joined
Aug 21, 2013
Messages
321
Loc.
Monmouth, OR
All depends on how deep in the hole the pistons are. Then you have the head gasket thickness.

You will also need to know for sure the CC on the heads before you can get a accurate number for compression.

Tim

Tim is correct you need exact piston to deck height I.E how much down in the hole at top dead center or even how much is sticking up, the exact cc of piston valve reliefs, and the cc volume of the heads. you want .035-.045 piston to head clearance for proper quench. head gaskets come in very many thicknesses with as thin as .027 up to .080 in a mls style. a typical .041 thick head gasket has somewhere right around 8cc of volume. for a accurate static compression ratio you need all the above info. on my last build the pistons stuck up .022-.023 so I used a .060 thick mls from cometic for a quench of .037-.038
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
As was said it kinda depends on your pistons. A rough estimate Id say your going to be at about 10-1 to 11-1 again all depends on the piston and its height to the deck. Its fairly common for shops to deck late model blocks .020 to the early 351W specs. Which kinda screws you if you decided you wanted a stroker.
Of course my numbers are just a rough estimate they could be higher or low. If you end up on the high side I would start looking at alumiunum heads. They will usually allow you to run the higher compression and low octane fuel without pinging. but then again maybe you can just run E85
 
Last edited:
OP
OP
GrillMaster

GrillMaster

Contributor
Bronco Guru
Joined
Jun 5, 2008
Messages
2,505
Thanks guys.. Great info. Once I get the pistons in I'll start by measuring the piston to deck. Why and how would I run E85?
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
If your engine ends up having very high compression then it may be a better idea to run E85 if its readily availible in your area. achohol likes high compression you'd probably have less issues than trying to run regular fuel. Plus the power would be about the same due to the high compression.
Wouldnt be my first choice to run E85 I was just throwing it out there.
 
Top