• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

cb antenna

Landshark

Sr. Member
Joined
Dec 22, 2002
Messages
440
Loc.
California
eds66bronco said:
it is only the lp pump. i can disconnect it and all the noise goes away (and the motor still runs at idle.) i'm not sure my airtex hp pump would be able to draw from my tank without the carter pump. i have the lp carter pump feeding an accumulator with the hp pump drawing out of that. where is the best place to get a noise filter.


Noise filter won't help. If you check the Ford TSL bulletins you’ll find one on just this subject. You can put a capacitor on the power side of the pump or a ferrite choke maybe (Don't think it will work, but worth a try). It will only help remove some of the noise, but not all of it.
 

twisted_mr

Full Member
Joined
Aug 12, 2006
Messages
182
Loc.
Calion, AR
choke/noise filter/capacitor all basically the same thing. Most noise filters are made up of an inductor and a capacitor...available at Radio Shaft or most anyplace that sells car audio eqpt. Landshark may know something I don't but the filter couldn't cost over 7 bucks (if that much) and won't hurt to give a try. Since you are filtering out noise to your CB it only makes sense to hook it (noise filter) to power wire of your CB. I'd be curious to know the results...Terry
 

ken75ranger

Bronco Guru
Joined
Jan 27, 2002
Messages
5,069
Loc.
Troy, NY
eds66bronco said:
it is only the lp pump. i can disconnect it and all the noise goes away (and the motor still runs at idle.) i'm not sure my airtex hp pump would be able to draw from my tank without the carter pump. i have the lp carter pump feeding an accumulator with the hp pump drawing out of that. where is the best place to get a noise filter.
I have the same problem with my Carter pump. %) Wired the CB direct to the battery including the ground. ZGP antenna and wire. If you find a solution please let me know. For now I'll keep the squelch.:p
 

Landshark

Sr. Member
Joined
Dec 22, 2002
Messages
440
Loc.
California
twisted_mr said:
choke/noise filter/capacitor all basically the same thing. Most noise filters are made up of an inductor and a capacitor...available at Radio Shaft or most anyplace that sells car audio eqpt. Landshark may know something I don't but the filter couldn't cost over 7 bucks (if that much) and won't hurt to give a try. Since you are filtering out noise to your CB it only makes sense to hook it (noise filter) to power wire of your CB. I'd be curious to know the results...Terry

Been running radio equip of one type or another for over the past 30 years, still doesn't mean much though LOL!!!! You have to do the mod at the source (meaning the pump) of interference. You can put all the filters you want on the radio end, but won't make difference because the noise is radiating from the wiring coming from the pump.
My current radio set up in the Bronco is a Magnum 257, Astatic 575 mic, Messenger 1200 with quick disconnect antenna mount ( I run either 102" ss whip or 5.5' quad wound antenna).
 

twisted_mr

Full Member
Joined
Aug 12, 2006
Messages
182
Loc.
Calion, AR
10-4, my EE degree and 30 + yrs selling electrical parts dont mean much either. lol. Still learn something new every now and then.

Here's a decent link to a similar situation ...

http://explorerforum.com/forums/showthread.php?t=48433

There is also a double braided coax available. I would think if you grounded the crap out of the outer braid that would help. If all else fails, crank up the squelch!

hth,
Terry
10-7 on this topic
 

Landshark

Sr. Member
Joined
Dec 22, 2002
Messages
440
Loc.
California
twisted_mr said:
10-4, my EE degree and 30 + yrs selling electrical parts dont mean much either. lol. Still learn something new every now and then.

Here's a decent link to a similar situation ...

http://explorerforum.com/forums/showthread.php?t=48433

There is also a double braided coax available. I would think if you grounded the crap out of the outer braid that would help. If all else fails, crank up the squelch!

hth,
Terry
10-7 on this topic

LOL!!! No 10-9 on what you say TFF!!! I put a .01uF ceramic cap on my 90 Ranger 4x4 elect fuel pump and it took some 90% of the noise. Since it's just the helper pump the easiest would be the ferrite choke wrap at the pump side.
 

eds66bronco

Bronco Guru
Joined
Aug 3, 2004
Messages
1,119
Loc.
Essex, Vermont
Landshark said:
LOL!!! No 10-9 on what you say TFF!!! I put a .01uF ceramic cap on my 90 Ranger 4x4 elect fuel pump and it took some 90% of the noise. Since it's just the helper pump the easiest would be the ferrite choke wrap at the pump side.
did you just jumper it between the +/- on the pump or is there a different way to wire it. i'll try radio shack on the way back home and pick one up.
 

feitctaj

FNG
Joined
May 3, 2003
Messages
4,319
Loc.
Group W Bench
I have a carter electric pump too and have no two way radio noise.
I hooked mine up with a cigarette lighter plug "cause mine goes to work with me too
 

eds66bronco

Bronco Guru
Joined
Aug 3, 2004
Messages
1,119
Loc.
Essex, Vermont
feitctaj said:
I have a carter electric pump too and have no two way radio noise.
I hooked mine up with a cigarette lighter plug "cause mine goes to work with me too

where is your pump located? mine is on the frame rail just in front of the rear bumpstop on the passenger side. that one feeds the accumulator/filter on the drivers side. (yes, i do have a beefy skid plate to protect it;) ).

still not really clear on how to wire a capacitor. would i splice the wire and put it between the power wire and the ground or could i just connect it between the + and - posts on the carter pump? electronics isn't my strong point... actually i don't have a strong point but i digress;D
 

Attachments

  • FuelSys3.jpg
    FuelSys3.jpg
    126.4 KB · Views: 36
  • FuelSys2.JPG
    FuelSys2.JPG
    88.7 KB · Views: 45

Landshark

Sr. Member
Joined
Dec 22, 2002
Messages
440
Loc.
California
eds66bronco said:
where is your pump located? mine is on the frame rail just in front of the rear bumpstop on the passenger side. that one feeds the accumulator/filter on the drivers side. (yes, i do have a beefy skid plate to protect it;) ).

still not really clear on how to wire a capacitor. would i splice the wire and put it between the power wire and the ground or could i just connect it between the + and - posts on the carter pump? electronics isn't my strong point... actually i don't have a strong point but i digress;D

The easier of the 2 ways is the method on the link given (That is a true rf choke). Otherwise, if you want to go with a cap install it at the pump across the posts. You can test it first without soldering and make sure it works ok for you. I would recommend that you remove the pump if you decide to hot solder it (SAFETY) after testing it to make sure it works ok.
 

eds66bronco

Bronco Guru
Joined
Aug 3, 2004
Messages
1,119
Loc.
Essex, Vermont
Landshark said:
The easier of the 2 ways is the method on the link given (That is a true rf choke). Otherwise, if you want to go with a cap install it at the pump across the posts. You can test it first without soldering and make sure it works ok for you. I would recommend that you remove the pump if you decide to hot solder it (SAFETY) after testing it to make sure it works ok.

good to know. i'll solder some lugs on the ends of the cap wires and use nuts to attach them to the posts. i sure hope this works 'cuz i'm sick of working on it:p
 

Landshark

Sr. Member
Joined
Dec 22, 2002
Messages
440
Loc.
California
eds66bronco said:
good to know. i'll solder some lugs on the ends of the cap wires and use nuts to attach them to the posts. i sure hope this works 'cuz i'm sick of working on it:p


Good luck. If that really doesn't work, though bigger go with the other RF choke. That is a sure way of doing it.
 
Top