• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

2M/70cm. Antenna for Bronco

Johnnyb

Contributor
Bronco Guru
Joined
Nov 19, 2001
Messages
1,233
Loc.
Flagstaff
Right now I've got a fairly tall antenna for my 2 m/70 cm setup. Fortunately it's mounted to my protofab bumper so it doesn't extend that far above the top of the cage, but it's also not working at peak efficiency because half of it is below the tub of the vehicle.
I was wondering what people are using as a durable off-road antenna setup?

THX,
JB
 
OP
OP
Johnnyb

Johnnyb

Contributor
Bronco Guru
Joined
Nov 19, 2001
Messages
1,233
Loc.
Flagstaff
Given the soft top or no top, I'm kind of stuck with a bumper mount on the protofab front or rear.
 
OP
OP
Johnnyb

Johnnyb

Contributor
Bronco Guru
Joined
Nov 19, 2001
Messages
1,233
Loc.
Flagstaff
I could definitely mount to the full cage, but it would have to be removable for when I want to put the soft top up.
My present situation will certainly get destroyed by trees at some point due to its exposure.
I suppose my best bet is to just take it down and go HT before hitting any heavy brush.

THX,
JB
 

Yeller

Contributor
Bronco Guru
Joined
Mar 27, 2012
Messages
7,692
Loc.
Rogers County Oklahoma
I have 2, an 18” 1/4 wave that I use for VHF that has been abused for years without any ill affects, it’s mounted about 4” down from the roof of my family cage on the passenger rear corner. For dual band or UHF I use a 36” dual band on the same mount, so far has done well. There have been some fantastic long range conversations with both, over 20 miles.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
I’ve had some pretty amazing results from magnetic base antennas. But whether unbolting or popping off a magnet, taking down to put the top on should not be a big issue.
You could even consider mounting an entire plate up top, whether out of aluminum, or steel, adding an actual ground plane.
You can still leave it on with the soft top, or just take the whole thing off with the antenna when you’re ready to swap over.
You still have to figure out what to do for an antenna with the top on, but when it’s down, you have a killer set up.
Not to mention some shade!
 
OP
OP
Johnnyb

Johnnyb

Contributor
Bronco Guru
Joined
Nov 19, 2001
Messages
1,233
Loc.
Flagstaff
I’ve had some pretty amazing results from magnetic base antennas. But whether unbolting or popping off a magnet, taking down to put the top on should not be a big issue.
You could even consider mounting an entire plate up top, whether out of aluminum, or steel, adding an actual ground plane.
You can still leave it on with the soft top, or just take the whole thing off with the antenna when you’re ready to swap over.
You still have to figure out what to do for an antenna with the top on, but when it’s down, you have a killer set up.
Not to mention some shade!
You know the magnet is not a bad idea. It could go on the hood or a few other places and would pop right off in the event of contact with brush.
 

pbwcr

Sr. Member
Joined
Jul 11, 2007
Messages
652
Good results for my various rigs has been an NMO fender mount. Far enough from the A pillar for low reflective signal degradation
Yes, the mag mount work but it is a pain to retrieve it when a bush gets it.
On a hardtop roof a deflector helps a lot , at least the NMO survives even though the antenna needs frequent replacement due to bending.
BTW all my choices of antenna locations have been broken or damaged by bushes.
 
Top