• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Centech Flasher Issue

Tedster100

Chairman of the Bored
Joined
Aug 25, 2010
Messages
1,762
Just completed the installation of my new Centech harness. Found that my turn signals are flashiing all the signals while signaling left or right. What's worse is that when the lights are off and I pull the emergency flasher switch, all the dash lights flash?? This happens even with the steering column disonnected. I took a quick look at the wiring and don't see anything that appears connected wrong.

Though I would post and see if anyone had a similar experiance or had an idea what might be wrong before I roll up my sleeves, cut all the wire ties and re-trace every wire.

Any ideas would be appreciated!

Thanks
 

aaron6920

Sr. Member
Joined
Sep 26, 2010
Messages
405
Loc.
Dorchester, IA
Hey Tedster100, I am also installing a centech kit at the moment (about 1/2 way through) My guess what is happening with yours is that everything is connected right at the steering connector but there is also those ends for the broncos that have the dash mounted hazzard switch. There is left, right, brake, etc... My guess is these connections are touching each other.

Did you seperate each of these with tape or tubing?
 
OP
OP
Tedster100

Tedster100

Chairman of the Bored
Joined
Aug 25, 2010
Messages
1,762
Actually, I have the switch with the plug so all the wires are in the plug, no way for them to touch. But you bring up a good point, if one of the wires is inserted into the wrong position in the plug it could be my problem. I'll check that out! Hope it's that easy!

Thanks for the post.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Have you already attached all the supplied ground circuits to a suitable ground? Clean the body good where you mounted them? If you mounted any to the dash, did you run a separate ground strap from the dash to the body?
And then, did you run new main ground straps between the battery and body, battery and engine, and engine and body?

I'm kind of baffled with your problem actually. But when that happens, I start checking all the grounds!!!

Paul
 
OP
OP
Tedster100

Tedster100

Chairman of the Bored
Joined
Aug 25, 2010
Messages
1,762
Yea, good grounds... motor to frame, motor to battery, dash, lights, etc... I started there by checking continuity and it's there. Well, guess it's time for a little snip-snip with the ties and re-trace the circuits. Already checked the flasher switch plug, it's all good.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Well that's a weird one then. Not computing at the moment.
You might just call Jim at Centech to see if he can troubleshoot any known circuits that might effect it like that. He's pretty good about that. A bit short and abrupt sometimes, when more detail might be nice, but he's knowledgeable and helpful when he's got the time.
I've caught him on more than one occasion when he was trying to get the day's shipping out and ready for UPS pickup, so needless to say, he didn't have time to talk at the moment.

It's all in the timing sometimes,

Good luck. If I can think of anything myself, I'll let you know.

Paul
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Just to make sure I'm clear here, when you say all the dash lights flash, you mean the instrument cluster lighting, correct? Does that include the high-beam indicator too? Or just the panel lighting and the turn-signal indicators?

Paul
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Don't think I asked this specifically before, but did you ground the instrument panel to the dash directly? I don't mean with the screws, but with a separate ground?

Paul
 
OP
OP
Tedster100

Tedster100

Chairman of the Bored
Joined
Aug 25, 2010
Messages
1,762
Instrument lights flash along with the flashers / signal indicators, no high beam flashing. Also, when you pull the light switch the instrument lights stay lit and no flasher.

On the ground to the instrument panel I need to look, wired the dash two months ago then broke my leg so I was working on more accessible and stationary projects like shifter knobs. Anyhow, I'll have to look, I want to say I did but I don't recall.
 
OP
OP
Tedster100

Tedster100

Chairman of the Bored
Joined
Aug 25, 2010
Messages
1,762
OK, I'm an IDIOT! I'm no expert at wiring but I'm not a beginner either. From the start my goal was bullet-proofing the rig so I could feel comfortable taking it on longer trips, etc. With that in mind every connection is soldered, double heat shrinked, taped up and ALL wiring is in a loom. You can't see more than a few inches of wire total in the engine compartment. I wired the dash on my bench just to make sure I got it right.

Soooo.. after calling Jim at Centech and discussing the problem he was also a bit puzzeled and played the ground card. I grounded the crap out of everything and couldn't belive that I still had a ground problem but he's the man so I figured I'd give it another go. Well, just before conceeding to re-checking the grounds I remembered the other item I added to make things more reliable, a LED light kit from Tom's. Jim's inital reaction was that the LED lights wouldn't work on the flasher due to not enough resistance, but I assured him that I installed the resisters furnished with the kit to solve that problem. THEN he asked me HOW I installed them, I told him that I installed across the pigtail hot to ground. I knew what I did as soon as I said it and he said the same thing. I installed the resistor across the running and signal wires not the signal and ground. DUHHHHH! Pulled the resistor and wired one end to ground on each side and what do you know, everything works!

Thanks everybody for the help and suggestions! I'm back on track and ready to move to the bodywork. It won't be long now!
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Wow! Good find. Score one for the good guys!
Hope you didn't have to take off too much covering to get to those bad boys. Even a little sucks, when you go to that much trouble to make it clean and reliable.
And now it is. Good show.

Paul
 
Top