• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Centech Flasher issues?

Ethansdad73

Bronco Guru
Joined
Apr 8, 2008
Messages
1,630
I did search and it does appear that there are some reply's but nothing like we seem to be having issues with.

I am assisting on a 76 with a 77 factory steering column and wheel with emergency flasher on the column. The turn signal switch is also new. The harness is new and installed and the bronco is running. All the lights work including the 4 way flashers when pulled.

However the right front turn signal and indicator in gage continue to flash with the key on and with the key off. The hazard flasher on the harness continues to operate. when its pulled from the harness everything operates as normal.

Any Ideas?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
The hazards will always work with the key off, so that's natural. I just did a '73 where the turn signals would work without the key too. The guy actually likes that, so I didn't dig into it any deeper, but warned him to always check his turn signal switch!
All the previous ones I've done did not have this issue.

It's possible that the turn signals are being powered through the same wire that feeds the flashers. If so they'd work all the time. I didn't spend much time working my way through the column connector, so don't know which wire might be swapped to where to get rid of this issue.
Have you spoken to Centech yet by any chance? If not, might be worth a quick call to see if they've got any idears.

Interested to hear what they have to say.

Paul
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Just re-read your post and it sounds like the indicator light is flashing at all times? Even if the turn signal switch is in the center?

Paul
 
OP
OP
Ethansdad73

Ethansdad73

Bronco Guru
Joined
Apr 8, 2008
Messages
1,630
Yes keys in pocket car off.. sits there blinking. Indicator switch centered
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Now that thar's a new one on me. Either a defective new TS switch, or some bleedover from another circuit through another channel, or something nefarious like that.

Assuming that if you disconnect the column from the harness all this monkey business goes away?

Paul
 

skerrybronco

Sr. Member
Joined
Aug 17, 2012
Messages
818
Loc.
Montreal,Canada
Yes keys in pocket car off.. sits there blinking. Indicator switch centered

I also had this problem, getting out of the truck I accidentally hit the indicator lever and it started flashing, with further investigation almost everything still had power. I also have a centech harness

http://classicbroncos.com/forums/showthread.php?t=223335

I ended up tracing it to the fuse panel, loose large power wire twisted enough to touch other circuits, adjusting and tightened fixed it, except my wipers are still independent.
hope this helps
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Yeah, if it does it with the column disconnected, you can eliminate the turn signal switch, or anything else in the column as a culprit. You're getting feedback through the wires somewhere.

Disconnect the hazard flasher unit, then the turn signal flasher unit, to see if either makes a difference.

Paul
 
OP
OP
Ethansdad73

Ethansdad73

Bronco Guru
Joined
Apr 8, 2008
Messages
1,630
If we disco the haz flasher from under dash it stops. And we have changed out the flasher and it still continues.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Nothing happens when the TS flasher is disconnected?

If it's flashing, it's not a sign of a bad flasher. To the contrary, it's working fine. The fault lies after the flasher somewhere, where either a circuit is grounded or otherwise letting power flow through the flasher instead of blocking it like a switch.

Maybe start disconnecting the turn signal/brake lights one at a time too?
Start with the fronts and, since you have easy connectors with the Centech harness, just unplug them to see if anything changes.

Paul
 
OP
OP
Ethansdad73

Ethansdad73

Bronco Guru
Joined
Apr 8, 2008
Messages
1,630
Forgot to update... the harness has the ability to wire the hazard at the dash or colum. In this case it was wired to the colum. The wires to the dash were taped together...grounding out and causing the issue. Rewraped each wire seperatly and problem solved
 
Top