• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Centech Harness Install

Borinqua Bronco

Jr. Member
Joined
Dec 31, 2016
Messages
64
Ok,
So after asking a million stupid (FNG) questions I have settled on the Centech harness and it arrived yesterday. I am looking to get any last minute pointers and lessons learned. Please don't hold back. All suggestions are welcome.
 

langester

MASTER OF MADNESS
Joined
Mar 2, 2013
Messages
2,681
Sorry no help here. I just got mine as well and am looking forward to the comments you get. Good luck with your install!
 

JaxLax

Bronco Guru
Joined
Apr 22, 2002
Messages
3,310
Loc.
Jacksonville, FL
Buy a good stripper/crimper.
Use heat shrink.
Add an aux fuse panel and plan on it's install NOW so it can be added to the loom for future additions. Never know when you'll want aux lights, stereo, gauges, etc things and it's better to have the circuits available than trying to tap into existing ones [especially when hunting gremlins]. Hell, buy 2 and hook one up to battery for always on and one to be ign hot.

When I did both of mine (one Centech and one Ron Francis) I probably spent twice as long planning and thinking about routing and diagramming (my own roadmap for things NOT in the centech) than I did installing it.

"Give me six hours to chop down a tree and I will spend the first four sharpening the axe." - Abraham Lincoln
 

clarrance

Bronco Guru
Joined
Mar 3, 2005
Messages
2,675
Ok,
So after asking a million stupid (FNG) questions I have settled on the Centech harness and it arrived yesterday. I am looking to get any last minute pointers and lessons learned. Please don't hold back. All suggestions are welcome.

What year is your bronco? The wiring grommets coming through the firewall will need attention. If you have a later model with the larger factory holes you will need to grind off the lip of the hole in order to make the grommet seat properly, If using an earlier body you will need to drill the larger holes for the grommets. Test fit the grommets to the holes before you run all the wires.
 

rydog1130

Contributor
Bronco Guru
Joined
Jun 19, 2014
Messages
4,188
just did mine, what year bronco? I have a 68 and had to enlarge my fire wall hole on the dr side and cut a second hole at 1 3.8" on the pass side. with that said you might need a 1 3/8" hole saw. Good wire stripper are nice, I bought the orange handle ones from harbor freight and they worked great. I also bought these for the weather pack connectors provided. http://www.ebay.com/itm/Delphi-Weat...e=STRK:MEBIDX:IT&_trksid=p2057872.m2749.l2649 a little pricery but cheaper than most and they worked great. Get some good 3M tape, shrink tubing, save your old heater switch, some connectors like this http://www.ebay.com/itm/150-PK-10-2...e=STRK:MEBIDX:IT&_trksid=p2057872.m2749.l2649 and make sure you have "GOOD GROUNDS" bare metal is best!

if your running an automatic this might help on your signal switch out of your column
IMG_0065.JPG IMG_0107.jpg

ps if you don't have the ignition switch adapter get it if you want to run your original set of keys

everything else should be there
 

904Bronco

Contributor
Bronco Guru
Joined
Sep 28, 2004
Messages
6,720
Loc.
San Martin, CA
Wire loom (not split convoluted type, but similar to what Painless sells... for the wires in the windshield channel. If you "Think" you need to have any items up that way by the wiper motor pull a few extra... 18g wire will run most gauges or led lights. There is a limit on what the channel will handle...

Since you asked... NO crimp connectors. Get ones without a covering, lightly crimp and solder your ends on and then use lined shrink tubing over. HF sells a nice assortment box of shrink tubing.

Use the Factory Ford ignition switch and adapter. Re use the wiper plug and switch, those ends can be found at some auto parts stores.

The yellow Alt wire is only good for powering a 60 amp G1 style Alternator (Factory one). If that is what you have then you are good. Anything else requires a different set up, which will render your Alt gauge useless.
The yellow wire comes from the fuse panel with a fuseable link on it. Figuring that it will not handle more than 60 amps before it pops. Dirtdonk is a strong proponent of using that to power other things/accessories. I have it powering my headlight relays for H4 headlights.
 

ransil

Bronco Guru
Joined
Sep 6, 2003
Messages
8,138
Why did you choose centeck over the painless,ron francess or other wiring harneses
Cheap and easy install.

Depending on the build stock vs lots of mods and a place to mount the Ron Francis fuse box I would got RD everytime.

Sent from my SM-G920V using Tapatalk
 
Top