• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Changed intake now won’t start

Brewbro21

Sr. Member
Joined
Jul 4, 2004
Messages
919
So I changed my stock 2bbl to an Edelbrock 4 bbl intake manifold using an adapter to run my 2 bbl carb. It ran before and now it just turns over and won’t start. It will even backfire occasionally when trying to start. Any ideas what could be wrong? Something with my timing when I removed the distributor?
 

B RON CO

Contributor
Bronco Guru
Joined
Jun 29, 2016
Messages
2,484
Loc.
Statesville, NC
Hi, X2 on the ignition timing. First I would double check that the plug wires are in the correct order.
Then I would line up the timing marks and see where the rotor is pointing. Don't forget the rotor may be 180* out when the timing marks are lined up.
When #1 is firing the rotor should be pointing just to the left of the throttle linkage.
You have to figure out if if the timing is off a tooth or more.
All of my cars have a Sharpie mark on the distributor under the #1 plug wire so I can see where the rotor is supposed to be with the cap off.
Good luck
 

JSBX

Contributor
Sr. Member
Joined
Mar 10, 2010
Messages
652
Double check your plug wires to make sure that none got crossed. Ron beat me to it.
 
OP
OP
B

Brewbro21

Sr. Member
Joined
Jul 4, 2004
Messages
919
I did check the plug wires and they are good. So good chance it’s the dizzy. I thought I made sure to put it back the way it came out but, guess not!! How far off does it have to be to not start??
 
OP
OP
B

Brewbro21

Sr. Member
Joined
Jul 4, 2004
Messages
919
Are you guys setting the marks on the crank at top dead center or or you setting it to 10-12 degrees before?? Watched a video where the instructor set it at 10 degrees then did all the distributor stuff.
 

B RON CO

Contributor
Bronco Guru
Joined
Jun 29, 2016
Messages
2,484
Loc.
Statesville, NC
Hi, I start a TDC and drop the distributor in so the rotor points to the #1 wire on the cap. There is enough adjustment to allow you to set the timing. The vacuum advance can should not hit the engine.
Are you moving the distributor while you are cranking the engine?
Good luck
 
OP
OP
B

Brewbro21

Sr. Member
Joined
Jul 4, 2004
Messages
919
Hi, I start a TDC and drop the distributor in so the rotor points to the #1 wire on the cap. There is enough adjustment to allow you to set the timing. The vacuum advance can should not hit the engine.
Are you moving the distributor while you are cranking the engine?
Good luck

Ok. I’ll try that. I set it at 10 degrees on the crank. I’ll do TDC this time. No I’m not moving the dizzy while cranking.
 

B RON CO

Contributor
Bronco Guru
Joined
Jun 29, 2016
Messages
2,484
Loc.
Statesville, NC
Hi, if the rotor is near where it is supposed to be just move the distributor while cranking the engine. You need a remote starter switch or a helper. if clockwise doesn't help try counterclockwise. After it starts up check it with a timing light. With the vacuum advance line unhooked and plugged with a golf tee. Good luck
 
OP
OP
B

Brewbro21

Sr. Member
Joined
Jul 4, 2004
Messages
919
Am I overlooking something? It’s at TDC on compression stroke and it’s still backfiring during cranking and doesn’t start
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
you have a early 302 or a later 5.0 or a 302 with a 5.0 cam? firing up the intake is usually too far advance or wrong firing. put the engine on top dead center #1 pop the distributor cap and mark where rotor is pointing. look at cap is it pointing at # 1 plug wire. it needs to point at #1. if its a little bit rotate the distributor if more than a little bit pull the distributor and re-stab it allowing for the twist in the gears as it goes in. look at the link I sent you for distributor location and firing order depending on the cam you use.
 
OP
OP
B

Brewbro21

Sr. Member
Joined
Jul 4, 2004
Messages
919
you have a early 302 or a later 5.0 or a 302 with a 5.0 cam? firing up the intake is usually too far advance or wrong firing. put the engine on top dead center #1 pop the distributor cap and mark where rotor is pointing. look at cap is it pointing at # 1 plug wire. it needs to point at #1. if its a little bit rotate the distributor if more than a little bit pull the distributor and re-stab it allowing for the twist in the gears as it goes in. look at the link I sent you for distributor location and firing order depending on the cam you use.

How can you tell what 302 you have?? Its wired for the nonHO, and has been running that way for yrs.
I have done all that by putting it at TDC and still same issue. Will rotating the distributor a little bit fix the backfire??
 

gr8scott

Contributor
Bronco Guru
Joined
Jul 1, 2011
Messages
1,890
Am I overlooking something? It’s at TDC on compression stroke and it’s still backfiring during cranking and doesn’t start

Are you absolutely sure its at TDC on the compression stroke? How are you verifying this?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
And have you simply tried twisting the distributor yet? If it's close enough all you need to do is find a sweet spot and get it running. Then time it with a timing light because that's the only way to know for sure where you are.
You can time it by how it runs, or maximum vacuum, but a light makes it so much easier. With a light you can watch while the starter is cranking and see if you're too retarded, too advanced, or so far off you can't see the marks when the light flashes.

Good luck.

paul
 
OP
OP
B

Brewbro21

Sr. Member
Joined
Jul 4, 2004
Messages
919
And have you simply tried twisting the distributor yet? If it's close enough all you need to do is find a sweet spot and get it running. Then time it with a timing light because that's the only way to know for sure where you are.
You can time it by how it runs, or maximum vacuum, but a light makes it so much easier. With a light you can watch while the starter is cranking and see if you're too retarded, too advanced, or so far off you can't see the marks when the light flashes.

Good luck.

paul

I did that this morning.trying to start but nothing…even had a couple times where there where flames in the carb.
 
OP
OP
B

Brewbro21

Sr. Member
Joined
Jul 4, 2004
Messages
919
My carb, which is a motorcraft 2150 2 bbl, should be able to run on an edelbrock intake with an adapter from mr gasket correct? Also using that adapter I had to take off the EGR plate for clearance issues, but it was being used.
 
Top