• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Did I Kill My Tranny?

ryoungbronco

Bronco Guru
Joined
Jul 4, 2007
Messages
1,754
Loc.
Belmar, NJ
5 years ago I had my C4 completely rebuilt with new performance torque converter. I added ATF at the time, I think it was about 4 quarts. Over the past 5 years I've started the bronco on and off but never for more than 10 minutes and never drove it. Yesterday I went to try to take it on its maiden voyage and after putting it in drive, no go. I realize now that I didn't put enough ATF in. When I check the dip stick it shows plenty of ATF but no oil is passing through the lines going to the transmission cooler. Any suggestions?
 

doghows72

Bronco Guru
Joined
Jan 5, 2005
Messages
2,036
Are you sure you got the torque convertor seated all the way in. It has to click back a couple times to engage the pump.
Also if I remember right those should take a lot more than four quarts of ATF. But even with four in it should be trying to pump it.
 
OP
OP
ryoungbronco

ryoungbronco

Bronco Guru
Joined
Jul 4, 2007
Messages
1,754
Loc.
Belmar, NJ
Are you sure you got the torque convertor seated all the way in. It has to click back a couple times to engage the pump.
Also if I remember right those should take a lot more than four quarts of ATF. But even with four in it should be trying to pump it.

When I put the converter in it did click back a couple times. Plus wouldn't the trans and flywheel not fit properly if the torque converter wasn't seated correctly?
 

doghows72

Bronco Guru
Joined
Jan 5, 2005
Messages
2,036
That is correct to a point, I've seen some use the bolts to pull the torque converter into place.
Are you able to put more fluid in? I think those take like 10 quarts? I would need to look that up though.
I recently had an AOD that we ran into a simular problem and it turned out we had the wrong flex plate. It wouldn't allow the splines to engage the pump but it did go together fine. Kinda sucks to have to tear it apart about five times to figure it out.
Also,did you prime the torque converter before installing it? I usually pour a quart right into it before installing.
 
OP
OP
ryoungbronco

ryoungbronco

Bronco Guru
Joined
Jul 4, 2007
Messages
1,754
Loc.
Belmar, NJ
That is correct to a point, I've seen some use the bolts to pull the torque converter into place.
Are you able to put more fluid in? I think those take like 10 quarts? I would need to look that up though.
I recently had an AOD that we ran into a simular problem and it turned out we had the wrong flex plate. It wouldn't allow the splines to engage the pump but it did go together fine. Kinda sucks to have to tear it apart about five times to figure it out.

I did hear that it's about 10 qts. I'll have to look to see what flexplate I have. Thanks
 

bax

Contributor
Old Member
Joined
Aug 22, 2005
Messages
14,552
no fluid in the cooler line is a front pump not working corectly or a mud dobber nest in the cooling line ( blocked line) bad deal take it back out and check the front pump
 

suthernboy

Sr. Member
Joined
Feb 16, 2010
Messages
422
Loc.
Greenville, NC
no fluid in the cooler line is a front pump not working corectly or a mud dobber nest in the cooling line ( blocked line) bad deal take it back out and check the front pump

To Bax's point, blow the lines and the cooler out first before removal.
 

Mountain Ram

Recovering Masshole
Joined
May 8, 2011
Messages
3,387
Loc.
Abingdon, VA
You definitely don't have enough fluid in it... I think there are 4 quarts in the TC itself when operational. You should have 10-11 quarts in it- you need to check the level when the trans is warm, in park and engine running. Checking the level when off will give you an incorrect reading.
 
OP
OP
ryoungbronco

ryoungbronco

Bronco Guru
Joined
Jul 4, 2007
Messages
1,754
Loc.
Belmar, NJ
no fluid in the cooler line is a front pump not working corectly or a mud dobber nest in the cooling line ( blocked line) bad deal take it back out and check the front pump

To Bax's point, blow the lines and the cooler out first before removal.

You definitely don't have enough fluid in it... I think there are 4 quarts in the TC itself when operational. You should have 10-11 quarts in it- you need to check the level when the trans is warm, in park and engine running. Checking the level when off will give you an incorrect reading.

I've only checked when the engine is stopped. Thanks for the info!
 

smokinjoe

Bronco Guru
Joined
Jul 8, 2007
Messages
1,139
Loc.
New Braunfels, TX
You definitely don't have enough fluid in it... I think there are 4 quarts in the TC itself when operational. You should have 10-11 quarts in it- you need to check the level when the trans is warm, in park and engine running. Checking the level when off will give you an incorrect reading.

^^^ This! You're not even close at 4 quarts.

Should be an easy fix :)
 

bronconut73

Bronco Guru
Joined
Aug 7, 2012
Messages
9,919
I've only checked when the engine is stopped. Thanks for the info!



Only real concern now is was the torque converter primed with a little fluid before being installed. It will definitely hold a few quarts. It being dry wouldn't be too good but I got my fingers crossed for ya'.

Check it when it is really warm. Tranny fluid expands quite a bit when hot and that will effect the reading.
But you need like 4 or 5 more quarts.....

If all that checks out then.....

Bingo, Bango, Bongo....

I bet you are going to be fine now....

Keep us posted.
 

jw0747

Bronco Guru
Joined
Nov 22, 2006
Messages
2,434
Loc.
San Antonio, TX
Torque converter is probably dry. When the tc and the transmission are dry it takes about 11 quarts to fill both.
 
OP
OP
ryoungbronco

ryoungbronco

Bronco Guru
Joined
Jul 4, 2007
Messages
1,754
Loc.
Belmar, NJ
Ok, so here is what happened today. I took the advice that I probably didn't have enough ATF. I started the engine until it was warm and added ATF. Next thing I know there is ATF all over the ground. It looks like it is coming out of somewhere where the trans and transfercase come together. Is there an overflow in that area? I can't figure out what is wrong. It doesn't seem that any ATF is flowing through the trans. I'm going to unscrew the torque converter and flywheel to see if I can push the torque converter back further. Maybe I have the wrong flywheel and the torque converter isn't engaged. For the first time I'm contemplating if I should continue this project. Thanks for any help. Frustrated but trying not to give up hope.
 

doghows72

Bronco Guru
Joined
Jan 5, 2005
Messages
2,036
Unfortunately at this point if you've run the engine that long the torque convertor so probably toast.
I'm guessing it wasn't back far enough to engage all the splines. If you run it for more than a minute or two stuff starts to burn up.
I hope it's not that bad. As far as a vent only the one on top of the transmission that I know of.
Keep us posted and I'll cross my fingers it's a minor issue. Good luck.
 

suthernboy

Sr. Member
Joined
Feb 16, 2010
Messages
422
Loc.
Greenville, NC
There is a vent on the top of the adapter housing. On the driver's side just in front of the t-case shifter mounting bracket.
 

Mountain Ram

Recovering Masshole
Joined
May 8, 2011
Messages
3,387
Loc.
Abingdon, VA
There is a vent on the top of the adapter housing. On the driver's side just in front of the t-case shifter mounting bracket.

This... And when the trans is overfilled or the fluid overheats, trans fluid will come out and look as if it's coming out between the trans and tcase.
 

Cohammer

Full Member
Joined
Aug 31, 2014
Messages
199
Torque convertor

When I put my convertor back in it took me about 4 tries on and off to finally get that last click in place . Not sure why it was so hard for me because every time I had it in I thought it was all the way but it was not.
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
Ok, so here is what happened today. I took the advice that I probably didn't have enough ATF. I started the engine until it was warm and added ATF. Next thing I know there is ATF all over the ground. It looks like it is coming out of somewhere where the trans and transfercase come together. Is there an overflow in that area? I can't figure out what is wrong. It doesn't seem that any ATF is flowing through the trans. I'm going to unscrew the torque converter and flywheel to see if I can push the torque converter back further. Maybe I have the wrong flywheel and the torque converter isn't engaged. For the first time I'm contemplating if I should continue this project. Thanks for any help. Frustrated but trying not to give up hope.

Probably over-filled now. That's why the fluid is coming out the vent. You should be able to check the level with the dipstick. It just should be a little low if the fluid is cold.

Now why do you think fluid is not flowing? Did you disconnect a cooler line to check? Do you have any drive in any gears? Is your tcase in neutral?

No drive and no fluid certainly points to the pump. If the input shaft was left out you would have no drive but should have fluid. There are also a couple check balls in the pump stator that have a tendency to jamb up and block the cooling port. If this was the case you would still have drive though.
 
OP
OP
ryoungbronco

ryoungbronco

Bronco Guru
Joined
Jul 4, 2007
Messages
1,754
Loc.
Belmar, NJ
There is a vent on the top of the adapter housing. On the driver's side just in front of the t-case shifter mounting bracket.

This... And when the trans is overfilled or the fluid overheats, trans fluid will come out and look as if it's coming out between the trans and tcase.

^^^ Thanks this is where it looked like it's coming from.

Probably over-filled now. That's why the fluid is coming out the vent. You should be able to check the level with the dipstick. It just should be a little low if the fluid is cold.

Now why do you think fluid is not flowing? Did you disconnect a cooler line to check? Do you have any drive in any gears? Is your tcase in neutral?

No drive and no fluid certainly points to the pump. If the input shaft was left out you would have no drive but should have fluid. There are also a couple check balls in the pump stator that have a tendency to jamb up and block the cooling port. If this was the case you would still have drive though.

I disconnected the lines that go to the trans cooler on the radiator and it was bone dry. That tells me that the fluid isn't flowing. I've put the truck through all gears and nothing happens. Checked tcase as well. When I put it in park the wheels lock up, which tells me tcase and trans connection are fine. If tcase were in neutral the truck would move even when it is in park, correct?
 
Top