• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Distributor roll pin sheared

Cortez

Bronco Guru
Joined
Jan 29, 2009
Messages
1,205
Ok, happy and sad week...driving my eb daily this year and just ordered my Fitech and related accessories last Sunday. Then on the drive home from work on Monday on acceleration from a stop sign. Under pretty heavy acceleration I had a big backfire and she died. Tearing into it this morning and it appears that I've sheared a roll pin on the distributor gear. Which is at least 8 years old.

I guess at this point I should just strip off the old ignition and put on the Fitech with timing control and new distributor etc.

Is there any value in repairing the roll pin and getting her running before swapping to the fuel injection? Or take this as a sign and get into it...
 

bax

Contributor
Old Member
Joined
Aug 22, 2005
Messages
14,552
Not much of an excuse but I'm good with it. Roll pin sheared off so I need injection. I like it.

In the mean time pick your self up a composite gear from comp cams, a new pin, and keep going.
 
OP
OP
Cortez

Cortez

Bronco Guru
Joined
Jan 29, 2009
Messages
1,205
Yeah, I was next going to check for a broken timing chain which means time to upgrade the cam and related parts. Funny how that logic seems to makes sense in my head.
 

B RON CO

Contributor
Bronco Guru
Joined
Jun 29, 2016
Messages
2,484
Loc.
Statesville, NC
Hi, it is remotely possible there is trouble in the oil pump. The distributor gear drives that too. I would make sure the hex shaft drives the pump smoothly counter clockwise, and that oil pressure is good. Just sayin' . Better to think about that and check it out before losing oil pressure. Good luck
 

Steve83

Bronco Guru
Joined
Jul 16, 2003
Messages
9,360
Loc.
Memphis, TN, USA, Earth, Milky Way
x2

Something caused the pin to shear, and it wasn't the carburetor. So swapping fuel &/or ignition systems won't fix the root problem. You'll just end up with a LOT more money & effort in an engine that doesn't run.

Does the distributor shaft spin freely? If not, it's probably seized due to lack of oil flow. Is there trash in the block oil galley? Are you using the cheapest oil filters you can find? Are you using the cheapest oil?

If it does spin, then it must have been the oil pump that sheared the pin. Find out why.
 
OP
OP
Cortez

Cortez

Bronco Guru
Joined
Jan 29, 2009
Messages
1,205
Yeah I'll be pulling the pan to see what's up. Although in searching about the sheared pin issue it does appear to be a common phenomenon with the Mallory dizzy and small block fords. But yeah - curious as to how the force was generated to shear it and if that is tied to something more.
 
OP
OP
Cortez

Cortez

Bronco Guru
Joined
Jan 29, 2009
Messages
1,205
So here's what I'm learning...Mallory is known for not using pressed on gears and that their gears can become loose and lead to pin shearing as result of high revs (guilty), high volume pumps, or high viscosity oils. Looking closely I can see that the hole for the roll pin is out of round which could be caused over time I would guess as the gear becomes loose from wear and tear. I can say this...the gear slides on and off with absolutely no resistance so I tend to believe this may be what happened. Plan to change oil and check it out while she's down anyway.
 

Attachments

  • image.jpg
    image.jpg
    77.8 KB · Views: 152

bax

Contributor
Old Member
Joined
Aug 22, 2005
Messages
14,552
Wrong gear. There are 4 different gears for the mallory shafts. Because mallory has 4 different shaft diameters. Are you running a 351?
 
Last edited:

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
I had an identical problem with a 460. It turned out to be a tiny piece of wire, likely part of the pickup screen, that jammed the oil pump. I reassembled the pump and engine. It ran for years till I sold it. The only parts I needed were the role pin and pan gasket.
 

bax

Contributor
Old Member
Joined
Aug 22, 2005
Messages
14,552
Yes - 351 Windsor

Figured that. same distributor as the 351C / 400 and 460. just a different gear. Mallory used different shafts on the bigger motors. Why? No clue.
It is good to look into why it sheared. But if you can turn the pump shaft, I would not drop the pan. The loose gear would shear the pin on its own in time.
 

KyleQ

Bronco Guru
Joined
Apr 24, 2008
Messages
5,480
Yes - I just ran into that in my build thread swapping gears on my new distributor. The collars ended up being different lengths and the pin holes were in different spots.

20170419_181314_zps2n9rjtil.jpg
 

DJs74

Bronco Guru
Joined
Apr 1, 2014
Messages
1,135
Yes, I've been there. When they are off, I go 90° from the original hole and drill a new one. I also usually bump up to a Ø5/32" roll pin instead of using the Ø1/8", since I'm going to the trouble. I also go with a spiral roll pin for extra strength.
The distributor gear has a slight raised boss on the bottom... a thrust / bearing surface, when the gears are meshed and rotating (especially at high RPM), the cam gear will pull the distributor gear into it... toward the pump - the thrust surface is the limit. If the gear is installed short or too high toward the intake, the end result is potentially a bent roll pin or worst case... a sheared pin. Both bad!


DJs74
 

Steve83

Bronco Guru
Joined
Jul 16, 2003
Messages
9,360
Loc.
Memphis, TN, USA, Earth, Milky Way
...the thrust surface is the limit. If the gear is installed short or too high toward the intake, the end result is potentially a bent roll pin or worst case... a sheared pin.
If that's true; in the case of a gear that's farther down the shaft than it should be, the sheared pin would be a result of the distributor hold-down clamp force. But the gears would mesh the same, regardless.

If the gear is too far up the shaft, the mesh would be at a slightly different location on the driven (distributor) gear, but probably NOT enough to affect the quality of the mesh. And that tiny thrust load on the pin shouldn't affect the pin's lifespan.

But I'm not sure that the block actually has a surface for that gear to bear against.
 

DJs74

Bronco Guru
Joined
Apr 1, 2014
Messages
1,135
If that's true; in the case of a gear that's farther down the shaft than it should be, the sheared pin would be a result of the distributor hold-down clamp force. But the gears would mesh the same, regardless.

If the gear is too far up the shaft, the mesh would be at a slightly different location on the driven (distributor) gear, but probably NOT enough to affect the quality of the mesh. And that tiny thrust load on the pin shouldn't affect the pin's lifespan.

But I'm not sure that the block actually has a surface for that gear to bear against.


Yes, you are right regarding if the gear was positioned out of spec on the MAX end of the distance (greater than 4.038"), the gear could/would bottom out on the block boss forcing the gear toward the intake as the hold down is tightened. Yes, the meshing would probably still be OK but the block, the gear and the pin would be compromised and potentially destroyed.

Yes, the block (small blocks and big blocks) by design incorporate a bearing surface for the distributor gear - its the flat surface of the boss that pilots or aligns the end of the distributor... the boss that's located beside the cam gear and the one that maintains the oil pump shaft when you pull the distributor out.

The 4.031" to 4.038" distance is measured with all end play removed by pulling the distributor shaft outward. End play = 0.024" to 0.035"

Here is the link again
https://performanceparts.ford.com/download/pdfs/DistributorGearInstallation.pdf


DJs74
 

Boss Hugg

Contributor
Bronco Guru
Joined
Jun 8, 2010
Messages
2,213
The dreaded loose drive gear bites again. Stupid 3yo O'Reilly dizzy.
 

Attachments

  • IMG_20240329_175332_736.jpg
    IMG_20240329_175332_736.jpg
    238 KB · Views: 65

56f100bbw

Contributor
Bronco Guru
Joined
Feb 3, 2008
Messages
2,406
Loc.
Tucson / lakeside AZ
I had a motor home class C 460 engine driving back from San Diego swap meet QUALCOMM stadium in 1996 had a roll piin sheer off I was on on the side of the road for hours till I got it going it out. driving to tucson pulled the distributor out and the gear fell off but I hit a magnet and got it out. Tried to find a distributor and couldn’t but I did find a roll pin ,No timing Light hardly any tools it was a pain.
 
Top