• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Door insert fit

jcb9089

Sr. Member
Joined
Feb 22, 2007
Messages
510
First time running door inserts. I test fit but the gap doesn't look right so put straight edge against both sides...see pics.

I then sent pics to vendor and asked if defective. They replied they aren't and this is the way they are all made off original pattern. Also offered refund minus shipping.

For those running door inserts, is this the way they fit? I assumed bottom edge should be straight line.

Anyone have same experience or pics to share?

Thanks!
 

Attachments

  • passenger insert.jpg
    passenger insert.jpg
    44.1 KB · Views: 186
  • driver insert 1.jpg
    driver insert 1.jpg
    53.5 KB · Views: 168
  • pass fit.jpg
    pass fit.jpg
    31 KB · Views: 193
  • driver fit.jpg
    driver fit.jpg
    29.8 KB · Views: 167

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
Yep thats the way they fit. Takes allot to rework them and make them really nice. I used allot of dura glass to fit mine to my Bronco.
 

demesauce

Sr. Member
Joined
Apr 6, 2012
Messages
403
Loc.
Shaver Lake, CA
Ugh, no. Mine fit much better than that. Who did you order those from? Are they the single piece version? Or the ones with the metal packing plates?

I'd try to bend them back into shape, use heat and lots of patience.
 
OP
OP
jcb9089

jcb9089

Sr. Member
Joined
Feb 22, 2007
Messages
510
Yeah, just didn't look right and that's a lot of duraglass to fill. Bronco Design makes them one piece and that's why I went with them. Problem is, I'll be out $120 shipping total after return.
 

PaveBronco

Sr. Member
Joined
Oct 30, 2012
Messages
914
Yup, just like Rustytruck said, that's how they fit. I've owned two sets and they do take a lot of Glass reworking, trimming, test fit, sanding, filling, test fit, cutting, sanding, test fit, glassing. On my first set I trimmed down my body mount bushings because my door openings were out of spec, didn't notice too much with hard doors on. It did help the bottom bow. They are quality pieces, and with most vendor parts its not one size fits all.
I also built up the mount areas where the screws go through so they sit flush but are tight.
Good Luck
 

Attachments

  • Inserts1.jpg
    Inserts1.jpg
    27.1 KB · Views: 117
Last edited:

mrdrnac

Contributor
Sr. Member
Joined
Feb 6, 2010
Messages
577
WOW! Makes me appreciate my "Old" needing paint OEM Originals even more!
 

Attachments

  • 20181127_124834_resized.jpg
    20181127_124834_resized.jpg
    55.8 KB · Views: 133

suckerpunched

Sr. Member
Joined
Aug 24, 2006
Messages
882
nice to have a picture of an original to keep everyone in check. why can't the repro parts manufacturers figure out the bottom edge should be straight. does not seem like that would be difficult to figure out.
 
OP
OP
jcb9089

jcb9089

Sr. Member
Joined
Feb 22, 2007
Messages
510
My same thoughts. I was surprised when told they aren't defective and were made from original mold. I know one size doesn't fit all but figured bottom line should be straight since rocker line is straight.
 

migs

Sponsor/Vendor
Bronco Guru
Joined
Nov 12, 2011
Messages
1,451
I purchased a pair from Bronco Design in 2016 and they told me the same thing after I inquired if they might have been a defective batch. They are very sturdy and well made from a fiberglass standpoint, just not quite what I was expecting for form and fit. and on the set I had, One was smaller in the area between the hinge post and outer side of the fender, the driver's side was going to need to be cut and pulled out to line up with the outer edge.
I have an original U13 insert to compare with so I was able to compare and take some photos back then.
the Bronco Design units don't share the same contours as the originals, they are more angled, or flared if you will, around the door opening ridge.

I will also add that I have had a set of one piece inserts as well as the two piece style in hand before, both from wild horses, and though they still require some work for good fitment I feel they look much closer to that of the originals, and no wavy gap at the bottom.

Here are the pictures I took of the issues and comparing the Bronco Design inserts to the original U13 piece. The original is the yellow one in the pictures.
 

Attachments

  • IMG_6491.jpg
    IMG_6491.jpg
    86.7 KB · Views: 97
  • IMG_7092.jpg
    IMG_7092.jpg
    71.4 KB · Views: 98
  • IMG_7087.jpg
    IMG_7087.jpg
    83.9 KB · Views: 91
  • IMG_6503.jpg
    IMG_6503.jpg
    77 KB · Views: 90
  • IMG_6502.jpg
    IMG_6502.jpg
    79.6 KB · Views: 97
  • IMG_6501.jpg
    IMG_6501.jpg
    76.4 KB · Views: 101
  • IMG_6876.jpg
    IMG_6876.jpg
    59.2 KB · Views: 116
  • IMG_6489.jpg
    IMG_6489.jpg
    78.6 KB · Views: 94
  • IMG_6496.jpg
    IMG_6496.jpg
    90.2 KB · Views: 94
  • IMG_6498.jpg
    IMG_6498.jpg
    110.9 KB · Views: 102
  • IMG_6499.jpg
    IMG_6499.jpg
    73.5 KB · Views: 89

No Hay

Bronco Guru
Joined
Jun 4, 2014
Messages
1,657
Holy crap! I've wanted some for a while but didn't like the look and fit from a distance, but up close it gets worse!

The idea/purpose for me is to clean up the rough door opening, but that would not be a cleaner look.
 

bronkenn

Contributor
Bronco Guy
Joined
Apr 27, 2017
Messages
2,717
Loc.
Southeast Ohio
Looks like Cory should find an original set and make his molds from them. Those BD ones are unacceptable. I would be totally disappointed. I have looked over BD's products and they are usually very nice. Ken
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
The fact on ry pieces are thermo formed in a hot press from sheet stock and very expensive top and bottom steel tooling. They are not hand layed up fiberglass and they are not one piece units either. Your not compairing apples to apples. You are compairing a Ford to a Yogo.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Yeah, them pesky Yogos sure were a problem!;D

I wonder what it would cost, and/or how many would have to be sold to justify manufacturing in a more precise fashion again?

Paul
 

migs

Sponsor/Vendor
Bronco Guru
Joined
Nov 12, 2011
Messages
1,451
I'm not comparing the process of how the two are made, and I actually think the bronco design process is done very well and is much more durable than the original pieces.
I just think any good fiberglass artist would be able to make any shape they desired and maybe fix the issue of the curved bottoms that apparently multiple people have mentioned. And if the molds were made from original roadster inserts then clearly something is amiss now.
They do make nice stuff and I'll continue to buy parts from them, and I sure would love to see a place like them produce a more authentic looking two piece door insert for us guys restoring U13's;D
 
Top