• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

engine and trans swap questions

wesleydax

Full Member
Joined
Apr 12, 2011
Messages
331
well i have searched and not had much luck on finding answers. but when you dont know what your talking about it makes it harder to search. I have decided to swap my worn out 302 and 3 speed auto for a 5.0 with od trans. I have read about the explorer motor and trans but dont you need a controller or something for the trans? what year did they go to a computer to work trans? i have a 5.0 with auto in my 66 mustang and it has a cable to control pressure/shift would this work in the bronco. the engine swap i understand but the trans is where im lost.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
All depends on wjhat OD tranny you intend to use. If you use the AOD then its like your mustang if you use the 4R70W then you need a controller. There should be info on both transmissions and corresponding swaps in the link section.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
If you go with a reworked explorer harness/computer from EFIguy here, that will control the transmission for you. The stand alone controller is used when you don't have an engine computer capable of controlling the transmission, or you want more programming capability then a stock program. They started doing that in the eary/mid 90's.

So if you get a good engine and transmission (4WD/AWD), put a ZF to D20 adaptor on the back of the 4R70W (it does work) you could drop the whole package in and the only oil you would touch is plumbing in the transmission cooler. The computer does a lot better job controlling the transmission then the TV cable does.

Now as with just about every "I want an overdrive transmission" thread, what are your plans for gearing? For the most part the stock gearing doesn't like to work with the overdrive. So add that to the build list.
 
Last edited:
OP
OP
wesleydax

wesleydax

Full Member
Joined
Apr 12, 2011
Messages
331
didnt think about the tech section. I have 4:11 gear now and i dont know where i need to be. I wont be doing any upgrades to the motor. i think i like the idea of the computer controlling the shifts. stupid question whats a zf.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
A ZF is a heavy duty ¾-1 ton truck transmission. Granny and overdrive wrapped around a 3-speed. To adapt the generic full size Ford 6-bolt 31-spline transmission an adaptor was developed to make the front of the Dana 20 Bronco transfer case mimic the appearance of a full size truck transfer case. After a few years of being used exclusively with the ZF 5-speed someone woke up and realized that the same adaptor would work on almost any full size truck transmission. The 4R70W from the Explorer happens to share the same pattern and spline count as the full size trucks, like the ZF transmission. This makes adapting the Bronco Dana 20 much easier, as normally you would need the late AOD kit from AA, add in a couple extra parts, and rebuild the transmission to put the adaptor's transmission output shaft in. By using an adaptor for installing the Dana 20 behind a ZF it makes the Dana 20 a bolt on instead of needing to rebuild the transmission to adapt.

Not knowing your tire size, you will have to do your own calculations to figure what gearing you will need. Aim for about 2500 RPM at 70 MPH. 33's will be around a 4.88 gear.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Most likely a axle gearing swap would wake your current engine up and it wouldnt feel so worn out.
 
OP
OP
wesleydax

wesleydax

Full Member
Joined
Apr 12, 2011
Messages
331
my current motor has issues. bad blow by and valves worn. any vendor better than the other for changing gears
 
Top