• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Engine temperature gauge trouble

moffat

New Member
Joined
Dec 10, 2003
Messages
10
The temp. gauge on my 77 stock dash cluster quit working. I want to avoid buying an after-market gauge cluster. Where does the temp. gauge get its signal from? Are there any replacement parts that can be bought to keep the stock gauge in working order?
Thanks for the help.
Keep'm stock and on the road!!
 

72_EB

Contributor
66to77
Joined
Feb 4, 2003
Messages
4,982
It might simple be the connection at either the sensor or the gauge itself. Use some steel wool, clean them and retry it.
First might want to try a new sensor in the intake. Available at a good autoparts store.

If they temp gauge is the only one that went, it sounds like it may be the sensor. If not, I have a couple of gauge clusters I could part out and get you a temp gauge.
 

70_Steve

Old Guy
Joined
Dec 13, 2002
Messages
8,317
I just went through this with my temp guage.

There is a voltage regulator (of sorts.. ) behind the instrument cluster. It supplies power to the three guages. If the other two guages work then chances are, the voltage regulator is OK. The voltage regulator pulses power to the guages, so, depending on what kind of volt meter you have (analog vs digital), if you measure the voltage, it will look pretty strange. An analog meter will show the needle bounding back and forth from about 3 volts to about 10 volts. At least that's what mine did. My digital showed different voltages from 0.0 to 8.something...

My suggestion is to disconnect the oil pressure sending unit, turn the key on, and use your voltmeter to measure (look at) the voltage on that wire. This will give you an idea of what your meter will indicate for proper supply to the sending unit. Then, measure the voltage at the temperature sender. If its the same, then replace the temp sending unit.

If it's not the same, then measure the voltage at the back of the temperature guage in the instrument panel. The temp meter has two wires on it. The black (with a white tracer???) is the supply from the voltage regulator. The other wire, red with white tracer, is the one going out to the temp sending unit. Measure the voltage at the back of the guage, where the red/white wire is. If you don't have proper voltage, the guage is bad. If you have voltage, then the wire is broken somewhere between the guage and the sending unit.

I found a bad connection at the firewall wiring harness connector. The female connection was broken down inside the connector. I
engineered a fix by running one new wire from the gauge to the engine compartment side of the harness. This will do 'till I install a new replacement harness...
 

feitctaj

FNG
Joined
May 3, 2003
Messages
4,319
Loc.
Group W Bench
moffat said:
The temp. gauge on my 77 stock dash cluster quit working. I want to avoid buying an after-market gauge cluster. Where does the temp. gauge get its signal from? Are there any replacement parts that can be bought to keep the stock gauge in working order?
Thanks for the help.
Keep'm stock and on the road!!
What state do you live in? I have a box full of senders
 

Skuzzlebutt

PhD, Dr. of Broncology
Joined
May 26, 2001
Messages
4,393
Loc.
Honeymoon Bay
First of all, check that the wire is connected to the temp sensor. If it is, disconnect it and check it for voltage. If it has voltage, connect it directly to a ground and check the gauge. If the gauge is pegged to the hot side it is good and the temp sensor is bad.
If the is no voltage in the sensor wire, then you're gonna have to remove the gauge cluster to inspect back there.

Obviously (I hope) this is all done with the key turned to ON or ACC.
 

66bronc

Jr. Member
Joined
Sep 9, 2003
Messages
124
Loc.
Jourdanton
i am having the same problem with my temp gauge, but it am pretty sure mine is bad. i am not getting any power out of the gauge, but i know it is going into it and i have already replaced the sensor before that. i was wondering if i could get one of those working gauges from you feitctaj. i will pay for shipping, i am in texas. this would be greatly appreciated also am having the same problem with my fuel gauge. don't mean to barge in on some one elses thread but i am in need of these two gauges.

thank you
 
Top