• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Explorer fan blade orientation/ direction

mgb0302

Sr. Member
Joined
Jun 29, 2002
Messages
429
Does anyone have a pic of their Explorer fan mounted? I am trying to figure out the proper orientation of the blades.

For years I have fought with engine running hot at idle and while wheeling. I went to a serpentine set up which greatly reduced temps. However I still have to manage temps at idle and while wheeling.

When I did the serpentine swap, I but the plastic blade fan that goes with Explorer 5.0 but a previous post of mine had a lot of replies stating the fan blade was backwards.

Any help is appreciated
 

MarsChariot

Contributor
Planetary Offroader
Joined
Oct 12, 2004
Messages
2,605
Loc.
Albuquerque, New Mexico
As I recall it really only fits one way. Here is an example:
 

Attachments

  • PC249733 copy 2.JPG
    PC249733 copy 2.JPG
    207.2 KB · Views: 208

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
The concave side of the blade is where you want the air to go (engine side). You can use that for any engine fan, or window fan, or anything shy of centrifigual or squirrel cage.
 

jeffncs

Contributor
Bronco Guru
Joined
May 4, 2004
Messages
1,898
Loc.
Raleigh, NC
The concave side of the blade is where you want the air to go (engine side). You can use that for any engine fan, or window fan, or anything shy of centrifigual or squirrel cage.

Technically - the concave side is marked “front” on the factory fan. The convex side faces the engine on the one.

🤷‍♂️
 

ksagis

Contributor
Aspiring Bronco Guru
Joined
Jun 15, 2020
Messages
819
Loc.
Austin
Pretty sure I remember this correct, standing in front, looking back, the fan should spin counter clockwise.

With a fan blade at TDC, the left side of blade is closer to front of vehicle than right side of fan blade.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
Pretty sure I remember this correct, standing in front, looking back, the fan should spin counter clockwise.

With a fan blade at TDC, the left side of blade is closer to front of vehicle than right side of fan blade.
All correct, but if you flip the fan on the clutch (most fans it can be done) the above is still correct. But the scoop of the fan blade will mostly stir the air and not actually move that much.
 
OP
OP
M

mgb0302

Sr. Member
Joined
Jun 29, 2002
Messages
429
As I recall it really only fits one way. Here is an example:
Thanks for the pic!! This is what I needed!! My fan is oriented the same as yours. However, the curve of my blades are opposite of what yours are. I don’t know why that is and I think that may have something to do with cooling at very slow speeds. What fan do you have on yours? I believe mine was simply from a 1999 Ford Explorer 5.0. But who knows the kid at AutoZone may have ordered the wrong part.
 
OP
OP
M

mgb0302

Sr. Member
Joined
Jun 29, 2002
Messages
429
Pretty sure I remember this correct, standing in front, looking back, the fan should spin counter clockwise.

With a fan blade at TDC, the left side of blade is closer to front of vehicle than right side of fan blade.
Well, the fan spends the same direction as the engine. So that should be clockwise - correct?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
No, the fan spins the opposite direction. Most serpentine belt driven fans do. Almost by definition.
If yours spins in the same clockwise direction, it sounds like your fan blades are oriented correctly.
The crankshaft always spins clockwise. If the serpentine belt wraps around the fan pulley on the smooth side, it’s a reverse rotation, and the blades reflect that.
If yours wraps around the fan pulley in the normal direction without using the backside of the belt, it would have blades meant to turn clockwise. But that seems like it would be a very unusual orientation.
Does your water pump/fan pulley have grooves or is it smooth?
Smooth and standard rotating would go against the typical “serpentine“ design. If yours is just a wide belt wrapped around everything in the same direction like a V belt is, then it’s not actually a serpentine drive.

How is yours set up? Got pics you can share?
Is it full explorer as I think you were saying?
Frankly, I’m surprised there’s an explorer type fan that does have blades opposite of what you’re seeing in the others pictures.
 

bronco italiano

Bronco Guru
Joined
Feb 1, 2004
Messages
2,595
Can you post a picture?
Do you have a fan shroud? If so, how far within the shroud are the fan blades?
 

SLOWnEASY

Contributor
Sr. Member
Joined
Sep 26, 2022
Messages
526
Loc.
San Diego, Ca.
Thanks for the pic!! This is what I needed!! My fan is oriented the same as yours. However, the curve of my blades are opposite of what yours are. I don’t know why that is and I think that may have something to do with cooling at very slow speeds. What fan do you have on yours? I believe mine was simply from a 1999 Ford Explorer 5.0. But who knows the kid at AutoZone may have ordered the wrong part.
Mine is a stock 97 explorer. From what you describe your fan is possibly mounted backward although I'm not sure if that's even possible. Like Dirtdonk says if it's serpentine belted is should be spinning counter clockwise (top of the fan spinning right to left) when standing in front of the Bronco looking at it. I'm sending you a private message.

Also I second the question of does the radiator have a fan shroud?
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
The fan blade curve. The leading edge cuts the air, the trailing edge pushed it. As the fan spins, think of the air wanting to be still and you want it moved. You cut it and use the scoop to push air back. High pressur on the concave side and as the air exits the blade it is going the direction you want. The leading edge of the blade is parallel to the radiator, perpendicular to the airflow. It has to be perpendicular to the flow so it can cut into it. As it exits the blade it is going the direction you want it to go.

If you flip the fan over, the general angle of the blade will still be right. But the scoop will be wrong. This is great if you put the fan in airflow and want to capture energy off it. But not good at putting energy in to get airflow. If the leading edge is parallel to the airflow, well it is rotating and just plowing through the air. Then where you want the air to exit the fan, the blade edge is perpendicular to the airflow.

Take a spoon and go to a carton of ice cream. The spoon has a scoop shape to it like a fan blade. The edge making contact with the ice cream is attacking it with and edge making a cut through it. The concave side of the spoon catches the ice cream and curves it to a new direction, out of the carton. If you hold the spoon at the exact same angle but flip it over. Same stroke of the hand. You are now plowing through the ice cream instead of scooping it. Lot more work, not nearly as much ice cream moved (you still get some, but nowhere near what scoping it the right way will result in. Look at the van blade and think if that was scooping ice cream, how well would it do it?
 
OP
OP
M

mgb0302

Sr. Member
Joined
Jun 29, 2002
Messages
429
No, the fan spins the opposite direction. Most serpentine belt driven fans do. Almost by definition.
If yours spins in the same clockwise direction, it sounds like your fan blades are oriented correctly.
The crankshaft always spins clockwise. If the serpentine belt wraps around the fan pulley on the smooth side, it’s a reverse rotation, and the blades reflect that.
If yours wraps around the fan pulley in the normal direction without using the backside of the belt, it would have blades meant to turn clockwise. But that seems like it would be a very unusual orientation.
Does your water pump/fan pulley have grooves or is it smooth?
Smooth and standard rotating would go against the typical “serpentine“ design. If yours is just a wide belt wrapped around everything in the same direction like a V belt is, then it’s not actually a serpentine drive.

How is yours set up? Got pics you can share?
Is it full explorer as I think you were saying?
Frankly, I’m surprised there’s an explorer type fan that does have blades opposite of what you’re seeing in the others pictures.
As always Dirtdonk, thanks for the help.

Slowandeasy is going to post a pic I sent him.

Yea, I forgot the fan rotates opposite direction of crank. Yes, my water pump pulley is smooth and rotates x-clockwise (truck in 100 pieces right now).
 

jeffncs

Contributor
Bronco Guru
Joined
May 4, 2004
Messages
1,898
Loc.
Raleigh, NC
I have the concave side facing the radiator. Not sure flipping it will clear the serpentine belt. If it does, it’ll be close…

IMG_1245.jpeg
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111

jeffncs

Contributor
Bronco Guru
Joined
May 4, 2004
Messages
1,898
Loc.
Raleigh, NC
Don't change it.
You have the definition of concave and convex backwards. Here is a link to describe the difference https://www.yourdictionary.com/articles/concave-convex-differences
It is installed correctly as shown in the picture.
I know my mistake. I missed a detail in your summary - that’s on me. You were talking about the concave shape of the BLADE facing the engine - 100% correct. I was referring to the overall shape/configuration of the fan assembly…. The font side has a set-back (or offset) shape which I was using in my description.

Glad we landed the plane! Sorry for creating any confusion!
 

SLOWnEASY

Contributor
Sr. Member
Joined
Sep 26, 2022
Messages
526
Loc.
San Diego, Ca.
Here's the picture of mgb0302's fan. It looks correct to me. I wonder if maybe your fan clutch is worn out. If it's good it should have a resistance trying to spin the fan with the engine off and cold. Mine if I grab the fan and give a hard spin toward the passenger side it only goes around maybe 1 revolution. If I quickly spin it again it only goes around maybe 3/4 of a turn. I'm assuming that's because the silicone in the clutch is now starting to flow.
 

Attachments

  • mgb0302 Fan blade.jpeg
    mgb0302 Fan blade.jpeg
    77.5 KB · Views: 85
Last edited:
Top