• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

F250 Shock Tower Welding

BigBlueBronco71

Full Member
Joined
Jul 14, 2013
Messages
310
Loc.
Santa Maria, CA
For those that have installed the F250 shock towers up front, how did you weld them to the frame?

My bronco has the engine and body installed so there is no easy way for me to get to weld the top of the frame and the mount is too close to the spring mount to weld both sides. Would it be adequate to weld only the bottom and one side? I'm concerned that this would pull the shock away from the frame and put torque on the mount. I was also thinking about enlarging the holes and plug welding them to the frame for extra strength. Let me know what you have done or what you think!
 

bronconut73

Bronco Guru
Joined
Aug 7, 2012
Messages
9,919
I bolted.
I then welded the bottom, one side, and a little of the top. Been great for many years.
 

RODRIG3911

Contributor
Bronco Guru
Joined
Jul 9, 2007
Messages
1,019
Loc.
Tucson
I bolted the bottom hole, plug welded the top hole, welded the bottom, top and the the side away from the spring and it's on there pretty strong. I got lucky and was in the process of installing new wheel wells, so the top was easy
 

Ol'Blue

Contributor
Bronco Guru
Joined
May 28, 2013
Messages
1,982
My welder plug welded the bolt holes, down one accessible side and along the bottom. It ain't going anywhere.
 

House

Contributor
Minutia Militia
Joined
Aug 12, 2004
Messages
2,440
I have welded them on also, but I want to add that I have seen more than one
pair just bolted on and wheeled hard with no issues at all...
If setup correctly your shocks should never be fully compressed or extended,
so no real pressure would be applied to them truthfully...
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
I suppose you could also "fishmouth" the lower portion to let you weld some extra vertical welds inside. But since it seems that most others are not having any issues with them as-is, the extra weld length would not necessarily be needed.

Paul
 

SteveL

Huge chevy guy
Joined
Jun 24, 2001
Messages
11,969
Loc.
Hawthorne ca
Some of the guys leave part of the stock mount so they can add height to the f-250 mount if you have a body lift.
 
OP
OP
BigBlueBronco71

BigBlueBronco71

Full Member
Joined
Jul 14, 2013
Messages
310
Loc.
Santa Maria, CA
Do have 1" bodylift but I already removed all of the old mounts and ground the frame down flush, I'll probably install everything and them play with tower placement and shock length to be sure everything works
 

toddz69

Sponsor/Vendor
Bronco Guru
Joined
Nov 28, 2001
Messages
11,222
Check out digger556's build thread on here to see how he extended the 'mount for the mount' a little bit at the frame. Simple and clean.

Todd Z.
 

garberz

Bronco Influencer
Joined
Jun 24, 2007
Messages
6,864
Loc.
Conejo Valley, Ca.
Do have 1" bodylift but I already removed all of the old mounts and ground the frame down flush, I'll probably install everything and them play with tower placement and shock length to be sure everything works

That's the correct and cleanest way to install the F-250 mounts. Some guys don't paint under the hood either. %)

Mark
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,622
Loc.
PNW
I extended it when I did mine back in '98. Simply put angle iron on either side of the F250 mount. Gives you more welding surface area and raises the mount up much higher so you can utilize all your travel...I'll try to find a pic...it was a long time ago... : )
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,622
Loc.
PNW
I just cut them off as I'm going with struts on all 4.
20 yrs and the sticker is still on it-FORD tough!! Ha

I'm obviously rerouting cables, hoses etc as stuff is hanging loose in the background... : (
 

Attachments

  • IMG_7960.jpg
    IMG_7960.jpg
    111 KB · Views: 127
Top