• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

First time bronco owner, send help!

KyleR

New Member
Joined
May 7, 2018
Messages
5
Loc.
Seattle, Wa
Hey Guys!

I recently bought a 1974 Bronco and couldn't be happier! With that being said, I have never restored a vehicle nor am I by any means a technical/mechanical kind of guy. I have recently ordered a 306ci w/ holley sniper from Maxlider bros/blue print engines. I am wondering what EFI setup I need to install that will work with that engine. I'd prefer to go with one tank and am looking for a good kit that will have (basically) everything I need to get that engine running at its best!

Second question,

I am looking to order a C-4 auto trans rebuild kit so the trans can handle the new power (370hp) without any issues, any recomendations?

This will be a daily driver and will not be used for off road.

Also, If anyone has any recommendations for a front disc brake conversion kits, 2.5 inch suspension kits, and anything else I may need to get this Bronco running right let me know!

PS, I am looking to purchase complete kits to try and avoid parts not fitting and minimual modifications!

Any suggestions or recommendations are welcomed!


Thank you!
Kyle
 

slim811

Sr. Member
Joined
Mar 6, 2013
Messages
709
Welcome aboard Kyler! Up until 2 am thinking about upgrading you're Bronco. You're in the right place. I'll let the other guys chime in on the tech. Just be sure to include your state in your profile. Lots of early Bronco clubs nationwide you can join. Good Luck with your Bronco.
 

pipeline010

Sr. Member
Joined
Nov 15, 2017
Messages
618
Does it not drive straight? Does not it start, run, or idle? Does it leak to the point of needing fluid every single morning? Is it rusted through to the point of needing a tetanus shot or too dangerous to drive?

If the answer to these questions is "No" I highly recommend, first and foremost, just driving and enjoying it for at least a few months before you go tearing it apart.

Everyone immediately begins with pie in the sky expectations but you'll find, especially if you have minimal technical experience, once you tear it apart you won't put it back together the way you thought you would...life gets in the way.

KEEP IT ROLLING is my advice. Fix the odds and ends as needed and pre-plan the hell out of any upgrades to the point where you know exactly how long it will take (and double that time) so you know how long you'll be off the road.

Wrenching can be satisfying but much more satisfying is actually driving it, daily. There's no such thing as really 'done' anyway.

EDIT: Point of fact, I'm a mechanical moron myself....a few weeks ago my axle seal blew out cause the bearings were shredded. After a week or so of learning I finally removed the axle, pulled the seal, grinded the bearings and retaining collar off, repressed all the pieces, and reinstalled the shaft.

So now I know:
1. Which bearings/seals/drums are used in my Ford 9".
2. How to use a slide hammer.
3. How to use an angle grinder (I removed my roof teeth last weekend with this new knowledge).
4. How to change differential fluid.
5. The purpose of the air valve in a differential.
6. How limited slip affects a hoisted rear.
7. How to properly seat a seal.
8. How to use a shop press.
9. How to use a torque wrench.
10. How to drink a beer to congratulate oneself.

Now, if any more of my axles go bad I can diagnose and be back on the road within a day (if I'm off work). As people that are new to wrenching it's important we learn these things before we go pulling everything apart.
 
Last edited:

PaveBronco

Sr. Member
Joined
Oct 30, 2012
Messages
914
I like number 10...it works also if you replace 'congratulate' with 'commiserate'.

And thanks KyleR, went to the Maxlider bros website and brought a pretty nice looking T Shirt for the girlfriend, should get me some brownie points.
 

904Bronco

Contributor
Bronco Guru
Joined
Sep 28, 2004
Messages
6,720
Loc.
San Martin, CA
Welcome KyleR ;D

So you are not wasting anytime jumping in to the Bronco world. I agree with some of the advise already given, drive it around for a while, enjoy it. That time spend in it will help motivate you to get it back together once it is apart.

I also suggest creating a punch list of things that must be done to make it mechanically sound and safe. HP motors with poor brakes is a bad mixture...

Any of the Vendors here carry complete Frt. Disc conversion kits, including HP sales on EBay. Prices are pretty close to one another, you need to find a sale to get the best prices. Also you have to consider shipping, which has gone up considerably as of late. There might not be any cost savings after that is figured in. Currently the Bronco Graveyard is having a 10% off sale.

Here is the disclaimer, once you jump into a project, you might find more work to do. Do a Frt Disc brake conversion and that would be the time to do a gear change and seal replacement in the front Diff, maybe u-joints in the axle shafts...

You said you are looking for a tranny rebuild kit, but you said you are not mechanically inclined. Would that work not be best left for a reputable local shop in your area, that gives a warranty, and can do follow up if there are issues. Sames goes, rebuild the tranny, you might as well have the T-case resealed and or rebuilt. Driveshafts are disconnected, so do u-joints there as well. (Wait on these if doing a suspension lift)

Suspension, well all the Vendors sell those products... But the shipping is a killer. Probably want to use a Vendor near you to keep costs down.
I like BCB's linear rate front springs, but shipping from TX is painful. Progressive rate front springs are ok. I have used WH's 11 pack rear springs and I have also had good luck with Deaver rear springs. Having used budget shocks before, I am very happy with the Bilsteins I bough for my 71 EB and 02 Superduty.

EFI... I have no feedback for the bolt on kits, used Ford factory stuff myself. Maybe others will chime in

Then there is Body, Paint, interior, electrical... It just goes on and on.

How about some pictures of your new ride? We all really like pictures here. Maybe even start a build thread! Good luck
 

needsmoarturbo

Full Member
Joined
May 13, 2015
Messages
278
Hey Guys!

I have recently ordered a 306ci w/ holley sniper from Maxlider bros/blue print engines. I am wondering what EFI setup I need to install that will work with that engine. I'd prefer to go with one tank and am looking for a good kit that will have (basically) everything I need to get that engine running at its best!

Holley sniper is the EFI fuel system isn't it??
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
Here's my different point of view. Getting the car down the road first, is satisfying, but can affect the final product.
My new Ranchero project will start with the body & interior. The chassis and drivetrain will be last.
The most important thing is to make a plan, and stick to it.
 
OP
OP
K

KyleR

New Member
Joined
May 7, 2018
Messages
5
Loc.
Seattle, Wa
Hey Guys, thank you for all the information!! I have answers to a lot of the questions asked and have a base plan on parts I want to replace, and the body work to be done. I will post my ideas and plan (once I figure out how to upload pictures and files to this thread lol) I found the FAQ sections and will go through that figure out how to work this platform so I know what I am doing and can respond to individual people who commented. Stay tuned!

once again, Thank you for all the responses!!! :)
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Holley sniper is the EFI fuel system isn't it??

Yep. But I think he meant the support system, as in fuel tank and pump and lines.
And any other parts of the snowball that might be needed on top of that!%);D;D

Paul
 

Eoth

Bronco Guru
Joined
Mar 10, 2004
Messages
1,692
First off, welcome to the addiction! This site has a ton of great people and information (and opinions ;D). People will help you go in any direction you want. That being said, you might want to reach out to a vendor that you see advertised on this site. You are not in uncharted territory and they can sell you parts/kits that are designed to work together and they will be available for "technical support" when you run into problems. Sure you can save a buck or two cobbling things together and pulling parts from junkyards but nothing beats being able to pick up the phone when something doesn't seem right.
 
Top