• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Floor pan support bent?

Millercorey

Full Member
Joined
Mar 15, 2017
Messages
232
Tearing out old floor pans to weld in new, and when I got to the 2nd passenger support it looks almost...bent??? I'm not sure how it happened, if I should cut out and replace with a new one, and the impacts that may have.

Take a look at the pics and let me know your thoughts. My big concern is if this thing is truly bent down by a small bit, then that means the right side of my bronco is hanging low. If I wanted to replace with a new straight support, I guess I would have to jack up that side of the body before I welded in the new support and support brace to make sure everything lined up?

My big concern is that this is a symptom of a FAR greater problem. FYI - the holes in the dash to screw in the windshield support don't line up correctly. Almost like the dash is 1/8" too low on the passenger side. I'm not sure if that's connected (meaning my entire right side has dropped 1/8").

On the flip side, you probably can't see it in pictures, but it almost looks like the body support has kind of "dimpled" up through the support, which if that's the case, makes me feel better about what I'm seeing here.

Either the support comes out from the centerline nice and straight and then bends down towards the exterior of the body (WORST CASE)

OR

Everything has kind of sagged down around the body mount creating kind of a reverse of the dimple you see in the floor pan. (SEEMS LIKE A BETTER PROBLEM TO HAVE)
 

Attachments

  • IMG_20180115_123139.jpg
    IMG_20180115_123139.jpg
    93.1 KB · Views: 202
  • IMG_20180115_123115.jpg
    IMG_20180115_123115.jpg
    82.2 KB · Views: 163
  • IMG_20180115_123103.jpg
    IMG_20180115_123103.jpg
    89.5 KB · Views: 210
  • IMG_20180115_123056.jpg
    IMG_20180115_123056.jpg
    77.4 KB · Views: 187

904Bronco

Contributor
Bronco Guru
Joined
Sep 28, 2004
Messages
6,720
Loc.
San Martin, CA
I am thinking that it moved because maybe the old patched floor was weak and supporting that weight plus bouncing down the road made it move.

I would think that it would need to be straightened (rather than replace) out before you weld in new... And it may have affected other alignments in the Bronco as well.

I am sure others will chime in
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
If it was mine I would clamp it down at the body mount and put a board and jack at the outer end and jack it up straight again. With everything cut out like it is it will bend back really easily. The Bronco body is really strong when everything is welded solid and intact but is just a house of cards when you have structural failures. Once the floor rots away one little hop could cause this bending.
 

WILDHORSES

Sponsor/Vendor
Bronco Guru
Joined
Nov 7, 2003
Messages
2,253
Loc.
USA
Very common issue and typically worse on the driver side because of the side tank slots in the floor brace. Especially noticeable on the rock crawlers. There is a lot of weight hanging past the body mounting points. Good luck with the project.

Jim
 
OP
OP
Millercorey

Millercorey

Full Member
Joined
Mar 15, 2017
Messages
232
Very common issue and typically worse on the driver side because of the side tank slots in the floor brace. Especially noticeable on the rock crawlers. There is a lot of weight hanging past the body mounting points. Good luck with the project.

Jim

So what's the best fix? Try to bend it back or replace? If bending is the answer, what's the best method?
 

nickgp

Bronco Guru
Joined
Jan 17, 2010
Messages
1,024
My body man friends favorite two professional tools: a big f ing hammer and a big block o wood!
 

WILDHORSES

Sponsor/Vendor
Bronco Guru
Joined
Nov 7, 2003
Messages
2,253
Loc.
USA
My body man friends favorite two professional tools: a big f ing hammer and a big block o wood!

He's old school and so are all these Broncos!

So what's the best fix? Try to bend it back or replace? If bending is the answer, what's the best method?

I'm not a body man by any means but if I were I would straighten it and add some sort of support bracing to try and keep it from happening again. Come to think if it I did weld 1/8" plate under the entire length of those braces in my wives Bronco and added 1/8" plate to all the body mounting locations. The body was on a rotisserie so it was easy at that time. Can't tell you how well it worked it's just about ready for paint now.

Jim
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,622
Loc.
PNW
x2 what Jim is saying...if you start looking at those floor body mounts on most Broncos they are dimpled from the weight and abuse. I beefed mine up there and doubled up the body mount in that location about 18 years back.
 

cldonley

Contributor
Bronco Guru
Joined
Jul 4, 2011
Messages
1,398
Loc.
Robinson, TX
I straightened mine with a floor jack and a short piece of 4x4. Mine was bent on the driver side as was mentioned above. Everything lines up and the doors close fine, but when I straightened mine I had a brace welded in the doors to keep the spacing right.

The brace needs a solid floor welded in to make the whole business hold its shape.

I haven't done it yet, but plan to weld a 1" angle to mine to keep it from sagging in the future.
 
Top