CopperBronco
Sr. Member
- Joined
- Aug 13, 2021
- Messages
- 389
Hey all, I've read many many forums on here, and still having fuel gauge problems.
With all wires detached, my new tank/sending unit read at about 40 ohms... and before installed read 10-77 ohms. I should note that my temp and oil pressure gauges already work, but there's a new IVR on the back of the instrument cluster as well. I'm getting about 4.7 volts off back of positive side of fuel gauge, engine temp had about the same... so it seems like IVR is working and doing its job.
When I ground fuel gauge on back of cluster, the gauge pegs to full, I'm told this means gauge is in good working order. Getting more suspicious by the day though as it's one of the few things I haven't replaced, but you can tell fuel gauge has been replaced at one point.
I decided to pull out instrument cluster and jump the wiring straight to the sending unit. I was using 16 gauge primary wire... I used alligator clips between gauge and sending unit connections on main tank and got nothing(I was grounded from the sending unit to the frame as well). So I wired and crimped up a snap terminal for the cluster and a sending unit connector at the tank to make sure I had good connection in wires... still no luck with the fuel gauge. Because I get good Ohm reading off of sending unit when vehicle is off, and the gauge pegs to full when grounded, I thought wiring was surely the problem, and the wiring job is a little spotty in a few areas when I got this Bronco. But I've had no luck with new wiring.
With new wiring jumped from gauge to sending unit directly, when key is off I get a 40 ohms reading, but when I turn the key to On position the Ohms drop to OL on my multi-meter. Which would explain why my gauge is stuck on empty.
I did read you can fry your gauge if you ground for too long... I've pegged it a number of times now, do I need to replace my gauge?
When Ohm testing, should I be getting same Ohm reading at sending unit connectors, & at fuel gauge?
Just to be certain, how do I test and make sure my grounds are good on the frame? Want to make sure I'm not going haywire all over a grounding issue. I have a battery to engine block ground, and battery to frame ground, also added a ground between body and frame near auxiliary tank, and cleaned up ground back at the sending unit. My instrument cluster is also grounded twice to the body/dash.
I've also jumped all cables to an extra sending unit I have, directly from fuel gauge to the unit... it behaved inconsistently for me... when I connected it via alligator clips, I grounded to dash/body and it pegged full, but when grounded with an alligator clip to the top of a ground screw in the frame, I would hook up sending unit, move the float around, and the gauge would stay empty, but maybe hover up just a tad... but not really move...
Any help of advice would be greatly appreciated! I did a ton of research to try and get this right and still getting stumped.
Brent
With all wires detached, my new tank/sending unit read at about 40 ohms... and before installed read 10-77 ohms. I should note that my temp and oil pressure gauges already work, but there's a new IVR on the back of the instrument cluster as well. I'm getting about 4.7 volts off back of positive side of fuel gauge, engine temp had about the same... so it seems like IVR is working and doing its job.
When I ground fuel gauge on back of cluster, the gauge pegs to full, I'm told this means gauge is in good working order. Getting more suspicious by the day though as it's one of the few things I haven't replaced, but you can tell fuel gauge has been replaced at one point.
I decided to pull out instrument cluster and jump the wiring straight to the sending unit. I was using 16 gauge primary wire... I used alligator clips between gauge and sending unit connections on main tank and got nothing(I was grounded from the sending unit to the frame as well). So I wired and crimped up a snap terminal for the cluster and a sending unit connector at the tank to make sure I had good connection in wires... still no luck with the fuel gauge. Because I get good Ohm reading off of sending unit when vehicle is off, and the gauge pegs to full when grounded, I thought wiring was surely the problem, and the wiring job is a little spotty in a few areas when I got this Bronco. But I've had no luck with new wiring.
With new wiring jumped from gauge to sending unit directly, when key is off I get a 40 ohms reading, but when I turn the key to On position the Ohms drop to OL on my multi-meter. Which would explain why my gauge is stuck on empty.
I did read you can fry your gauge if you ground for too long... I've pegged it a number of times now, do I need to replace my gauge?
When Ohm testing, should I be getting same Ohm reading at sending unit connectors, & at fuel gauge?
Just to be certain, how do I test and make sure my grounds are good on the frame? Want to make sure I'm not going haywire all over a grounding issue. I have a battery to engine block ground, and battery to frame ground, also added a ground between body and frame near auxiliary tank, and cleaned up ground back at the sending unit. My instrument cluster is also grounded twice to the body/dash.
I've also jumped all cables to an extra sending unit I have, directly from fuel gauge to the unit... it behaved inconsistently for me... when I connected it via alligator clips, I grounded to dash/body and it pegged full, but when grounded with an alligator clip to the top of a ground screw in the frame, I would hook up sending unit, move the float around, and the gauge would stay empty, but maybe hover up just a tad... but not really move...
Any help of advice would be greatly appreciated! I did a ton of research to try and get this right and still getting stumped.
Brent











