• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Full width 78-79 Bronco rear diff swap

dgold_881

Sr. Member
Joined
Nov 24, 2009
Messages
368
I'm finally getting around to welding the spring perches on my full width axle swap but wanted to make sure the Pinion angle is correct before I welded them. I attached the angle meter photos. For info Its a 5 1/2" wild horses lift with 78 Bronco full width axle swap. What should the degree be so theres no issue with bind or wobble?

Thanks for any help.
 

Attachments

  • 2014-09-29 17.10.46.jpg
    2014-09-29 17.10.46.jpg
    85.6 KB · Views: 104
  • 2014-09-29 17.12.43.jpg
    2014-09-29 17.12.43.jpg
    102 KB · Views: 109
  • 2014-09-29 17.12.10.jpg
    2014-09-29 17.12.10.jpg
    76 KB · Views: 117
  • 2014-09-29 17.12.20.jpg
    2014-09-29 17.12.20.jpg
    73.9 KB · Views: 99
  • 2014-09-29 17.11.08.jpg
    2014-09-29 17.11.08.jpg
    62.9 KB · Views: 118
  • 2014-09-29 17.10.59.jpg
    2014-09-29 17.10.59.jpg
    88.3 KB · Views: 98
  • 2014-09-29 17.10.29.jpg
    2014-09-29 17.10.29.jpg
    90 KB · Views: 97

76Broncofromhell

Bronco Totalitarian
Joined
Jul 30, 2001
Messages
4,250
Loc.
Grass Valley, CA
Consensus is on a double-cardan CV you want the lower joint to be within 0-5* of the driveshaft at static height.

It looks like your axle is at about 16* and your driveshaft is at about 26* - which is too much angle. I would tilt the pinion up a few degrees and look at it again.

Remember the pinion is going to nose up under power slightly due to the nature of leaf springs, which is why you can have a bit of variance on the pinion being down angle from the driveshaft.

Directly parallel is not optimal because it doesn't allow the needle bearings to spin and can potentially flat spot needle bearings and u-joint trunions. That's in theory of course - in practice it's pretty much impossible on a leaf sprung rig since there is a lot of inherent movement in the suspension through travel, axle wrap and imperfect suspension angles.
 

frenchy

Contributor
Bronco Guru
Joined
Nov 29, 2005
Messages
1,043
Hi guys,I have a ? on this subject. 76bfh where would you place the angle meter to see if you have the 2* your talking about. I will be doing this someday and would like the info.

dgold881 I would like to see some pics of your front end. Is that the full width already installed? You can pm them to me if you like.
Thanks
frenchy
 
OP
OP
dgold_881

dgold_881

Sr. Member
Joined
Nov 24, 2009
Messages
368
I will try that in the morning.



Consensus is on a double-cardan CV you want the lower joint to be within 0-5* of the driveshaft at static height.


It looks like your axle is at about 16* and your driveshaft is at about 26* - which is too much angle. I would tilt the pinion up a few degrees and look at it again.

Remember the pinion is going to nose up under power slightly due to the nature of leaf springs, which is why you can have a bit of variance on the pinion being down angle from the driveshaft.

Directly parallel is not optimal because it doesn't allow the needle bearings to spin and can potentially flat spot needle bearings and u-joint trunions. That's in theory of course - in practice it's pretty much impossible on a leaf sprung rig since there is a lot of inherent movement in the suspension through travel, axle wrap and imperfect suspension angles.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
You may want to add some weight in the rear if you dont have stuff like gas tanks rear bumper or a cage ect installed yet. As its best to set the angle when at ride height. The closer you can get to 1 -1 1/2 degrees differance on the pinion angle vs the shaft angle the better.
 
OP
OP
dgold_881

dgold_881

Sr. Member
Joined
Nov 24, 2009
Messages
368
I can throw on the Proto Fab rear bumper on and put the front bumper in the rear to add simulated weight. The hard top is on as well.


You may want to add some weight in the rear if you dont have stuff like gas tanks rear bumper or a cage ect installed yet. As its best to set the angle when at ride height. The closer you can get to 1 -1 1/2 degrees differance on the pinion angle vs the shaft angle the better.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Yeah whatever you think will be close to what you intend on running. plus the rear may settle a little after some trail time. The front bumper in the rear may be close to what a tank of gas would be. May want to throw a spare tire and a cooler of beer back there to. then again the beer cooler might not stay full for long. lol
 

76Broncofromhell

Bronco Totalitarian
Joined
Jul 30, 2001
Messages
4,250
Loc.
Grass Valley, CA
Hi guys,I have a ? on this subject. 76bfh where would you place the angle meter to see if you have the 2* your talking about. I will be doing this someday and would like the info.

dgold881 I would like to see some pics of your front end. Is that the full width already installed? You can pm them to me if you like.
Thanks
frenchy

Put the angle finder on the driveshaft tube and then on the pinion housing or yoke.


You may want to add some weight in the rear if you dont have stuff like gas tanks rear bumper or a cage ect installed yet. As its best to set the angle when at ride height. The closer you can get to 1 -1 1/2 degrees differance on the pinion angle vs the shaft angle the better.

Yeah whatever you think will be close to what you intend on running. plus the rear may settle a little after some trail time. The front bumper in the rear may be close to what a tank of gas would be. May want to throw a spare tire and a cooler of beer back there to. then again the beer cooler might not stay full for long. lol


Solid advice. I usually stack whatever rig I'm doing with some sort of ballast to get the measurement right.
 
OP
OP
dgold_881

dgold_881

Sr. Member
Joined
Nov 24, 2009
Messages
368
Ok right now I have the lower yoke at 25 degrees and the drive shaft at 25 degrees should I put the yoke at 22 degrees to anticipate the up tork so that will be inline during acceleration? Or should the yoke be at 20 degrees?




Consensus is on a double-cardan CV you want the lower joint to be within 0-5* of the driveshaft at static height.

It looks like your axle is at about 16* and your driveshaft is at about 26* - which is too much angle. I would tilt the pinion up a few degrees and look at it again.

Remember the pinion is going to nose up under power slightly due to the nature of leaf springs, which is why you can have a bit of variance on the pinion being down angle from the driveshaft.

Directly parallel is not optimal because it doesn't allow the needle bearings to spin and can potentially flat spot needle bearings and u-joint trunions. That's in theory of course - in practice it's pretty much impossible on a leaf sprung rig since there is a lot of inherent movement in the suspension through travel, axle wrap and imperfect suspension angles.
 
OP
OP
dgold_881

dgold_881

Sr. Member
Joined
Nov 24, 2009
Messages
368
I finished the front end awhile back. I bought new heavy duty spring buckets and the extended coil spring towers from Duffs so that the coil wouldn't have to much of a bow in it. I cut off the old towers and welded them on. I attached some photos of the front end. Its a little rusty but will look great after I get it to media blast.


Hi guys,I have a ? on this subject. 76bfh where would you place the angle meter to see if you have the 2* your talking about. I will be doing this someday and would like the info.

dgold881 I would like to see some pics of your front end. Is that the full width already installed? You can pm them to me if you like.
Thanks
frenchy
 

Attachments

  • 2014-09-30 09.09.45.jpg
    2014-09-30 09.09.45.jpg
    88.1 KB · Views: 86
  • 2014-09-30 09.09.42.jpg
    2014-09-30 09.09.42.jpg
    92.3 KB · Views: 93
  • 2014-09-30 09.09.35.jpg
    2014-09-30 09.09.35.jpg
    90.1 KB · Views: 89
  • 2014-09-30 09.09.26.jpg
    2014-09-30 09.09.26.jpg
    76.3 KB · Views: 89
  • 2014-09-30 09.09.19.jpg
    2014-09-30 09.09.19.jpg
    92.7 KB · Views: 84
  • 2014-09-30 09.09.15.jpg
    2014-09-30 09.09.15.jpg
    103 KB · Views: 99
  • 2014-09-30 09.09.55.jpg
    2014-09-30 09.09.55.jpg
    94 KB · Views: 87
Top