• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Gear ratio

advracer67

Jr. Member
Joined
Jan 29, 2010
Messages
117
I'm looking to get better highway speed out of my recently restored stocker. This truck will never be off road or in the snow. No more road Salt ever!

It's a 1977 and currently geared to cruise at 55. I want to be able to cruise at 65-70mph. Any suggestions on where I could find the proper gear ratio for the differentials I need to accomplish this and how to go about getting it done properly?
 

Old School

Sr. Member
Joined
Jun 22, 2011
Messages
440
Loc.
AZ
Let's start at the beginning rather than a having a guess-fest.

What is your current gearing and what size tires to you have?
 
OP
OP
A

advracer67

Jr. Member
Joined
Jan 29, 2010
Messages
117
29 inch tires. I looked into larger tires but the gain was minimal.
The specs say
Front 3000lb - 3.54
Rear 2900lb - 3.50
 

Old School

Sr. Member
Joined
Jun 22, 2011
Messages
440
Loc.
AZ
That's just what I have- 29" 235/75-15 tires and 3:50's

You could go higher on the axle ratios but since it sounds like you're paying to have it done, I'd guesstimate $1500 or more to change the front and rear.
You will also suffer a very noticable loss of acceleration in around town driving.

I'm sure you are going to get suggestions for an overdrive transmission, but open your wallet twice as far as paying for gears.

Going to a 30" tire would be like raising your ratio 3.5%
 
OP
OP
A

advracer67

Jr. Member
Joined
Jan 29, 2010
Messages
117
Looks like you have a stocker as well from your profile pic. What are the biggest tires you think would fit?
 

Old School

Sr. Member
Joined
Jun 22, 2011
Messages
440
Loc.
AZ
I know 30x9.50-15's will fit with stock wheels on an uncut without problem.

Is yours cut out? What wheels do you have?
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
You could go with 33x9.50 or 10.50 tires and get a decent reduction in hiway RPM's it would be like dropping the axle gearing to 3.08's without have the added costs. Or as was said a OD transmission with your current gearing and tire size would probably be the best bet if you dont ever want to go with bigger tires. the OD tranny would drop the RPm's a little more than 3.08 gears or 33in tires. There are some cheap OD tranny swaps out there.
Now one other option since you dont really intend to use your bronco for anything other than street driving is to scour the junkyards for a rear center section that has 3.08 gears and is 28 spline. and swap it in you can usually get a complete center section for less than $100. Just dont ever put the bronco in 4wd with only the rear gearing changed.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
I presume a C4 automatic?

You actually need to carry some RPM at highway speeds. You don't have modern lockup torque convertor (and it won't go into a C4 if you did get one). If you gear too high then you will have excessive convertor slippage. You loose your effiency through the transmission and will burn extra gas to make the transmission hot.

While 3.50 gearing is a little low for a highway cruiser, it isn't that bad of a choice. Any gains will be minimal and the expense to get there generally won't pay for it. Then you sacrifice stop and go driving for it as well.

If this was a clean slate build I would probably recomend somewhere around a 3.00:1 gear (3.08, 3.25, something like that). But the 3.50 is close enough to not be worth changing. at least in my book.
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
A transmission changover would change the looks too much if you really plan to keep the stock look. If you really don't plan to off-road this beauty, I'd put in a set of 3.10 gears in the rear and 3.07s in the front. It would cruise great! Any higher than that and the little 302 will be worthless anywhere.
 

Quick & Dirty

Sr. Member
Joined
Feb 15, 2004
Messages
857
You're just used to modern, overdrive equipped vehicles.

Run the Bronco at 3000+ rpm. It'll be fine.

I used to take mine on 600 mile trips running all day at 3500 rpm. 3.50 gears, 31" tires (actual size was closer to 29").

Your biggest enemy is aerodynamics. It takes a lot more power to push a flat front end 70mph than it does to go 55. If your engine isn't up to it, taller highway gears (or overdrive) won't be your friend.
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
Set your timing to 12 degrees advanced and drive it. Whats limiting you now? It wont go over 55 or you just dont like the way it sounds?
 

Bronchole

Bronco Guru
Joined
Mar 24, 2004
Messages
1,611
Loc.
Chatsworth, Ca (LA)
Your current setup:
3.50:1 gears
cruise speed 55

Desired cruise speed 65 MPH at same RPM as current at 55 MPH

According to this calculator: http://www.grimmjeeper.com/gears.html

Your current RPMs at 55 are 2356 (Assuming C4/3.50:1)
Your current RPMs at 65 are 2785
Your current RPMs at 70 are 2999

To obtain the same RPM at 65 you would need 3.00:1 gears (actual calc is 2387 RPM)

As others have mentioned though, that is a pretty substantial shift in the non-power direction, but to each his own.
 

stock1970

Bronco Guru
Joined
Apr 2, 2008
Messages
1,793
Loc.
Olathe, Kansas
the 302 was built to turn 3k all day.. i drive my stocker and my other at 3k down the highway and never give it a second thought. With one exception.. make sure your timing gear does not have over 100k miles on it ... if it does it is time to change it before the chain slips and bends all your valves.. ..
 

trailpsycho

Bronco Guru
Joined
Dec 11, 2003
Messages
4,856
I used to drive mine all over the place with stock gearing, even before I put 31"s on it. They actually run great and have good power at 3K and really dont burn that much gas. I used to get 14 mpg running 75-80...it was a little loud. However, nothing a good stereo couldnt fix.

Funny thing, during my frame-off, I spent tons of money on the EFI, OD, gearing, big tires and a great suspension...so it would be set up "right" for running highway and interstate. Whats crazy is, that while it handles and rides great, especially for being lifted and on 35s, its even louder now than it was 'back in the day'. Go figure.

I think you should just drive it as is--the 302/5.0 loves 3K rpms...but if it bothers you enough, spend the 2K on the OD tranny. Afterall, its a Bronco; it should be a little ill-refined and burly...its a real, albeit little, truck...4-wheel drive muscle car...it has character. And it isnt for everyone. Thank God.
 
OP
OP
A

advracer67

Jr. Member
Joined
Jan 29, 2010
Messages
117
Thanks guys, mines a stocker so I don't have a tach. All I know is it sounds like its screaming on the highway. i should get a tach just to see where its running of r piece of mind. If its at 3k like you say its not bad. It just sounds like its running a lot higher. You all are right not eh aerodynamics. It's a truck with the aero of a brick and not a porsche. Thanks again!
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
Fans make massive amounts of noise. If it is stock you may have enough room to switch from the stock fixed fan to a thermal clutched fan. Electric is another choice but has other issues such as one that can flow enough air to actually keep a Bronco cool is more then the stock charging system can handle.
 

Bronchole

Bronco Guru
Joined
Mar 24, 2004
Messages
1,611
Loc.
Chatsworth, Ca (LA)
If you are just interested in knowing the cruise RPM consider temporarilly installing a tach just to check. That way you don't have to figure out where you will install it and you will have the info you desire. One of your friends should have a tach laying around that they use to use when doing a tune up.
 
Top