• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Grant Steering Wheel - Spring Needed?

NJBronk

Contributor
Sr. Member
Joined
Oct 11, 2022
Messages
369
My Grant steering wheel always makes a high pitched squeaking noise when turning. Sounds like metal on metal rubbing.

Am I supposed to have a spring or washer or something under the wheel adapter?

IMG_3018.jpeg


IMG_3019.jpeg
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Check the gap between the two outer shells. The one on the steering wheel and the one on the column, should have at least a 16th inch clearance. Perhaps more for the Grant, if there is any little bit of “Wobble“ to the housing.
Does it make the sound 360°? Or just partially?

I’m a fan of grease. I always use it even on the factory wheels.
The horn contact contact can wear quickly without it, but so can the far too thin copper traces on the back of the wheel.
I think I used to use dielectric, but with your setup with the single trace and the horn relay, you could probably use any long-term long life grease. Maybe silicone based grease?

Hopefully somebody will know the proper product to use.
 
OP
OP
NJBronk

NJBronk

Contributor
Sr. Member
Joined
Oct 11, 2022
Messages
369
Check the gap between the two outer shells. The one on the steering wheel and the one on the column, should have at least a 16th inch clearance. Perhaps more for the Grant, if there is any little bit of “Wobble“ to the housing.
Does it make the sound 360°? Or just partially?

I’m a fan of grease. I always use it even on the factory wheels.
The horn contact contact can wear quickly without it, but so can the far too thin copper traces on the back of the wheel.
I think I used to use dielectric, but with your setup with the single trace and the horn relay, you could probably use any long-term long life grease. Maybe silicone based grease?

Hopefully somebody will know the proper product to use.

Thanks, I’ll have to check the gap once I finish installing the turn signal cam and get it back together. But will likely try some grease and see if that helps.

Dielectric makes sense to me for the horn contact.

It makes the noise pretty much 360.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Actually, maybe not dielectric.
Reason being, since it will be a lubricant between the contact point and the copper trace on the back of the wheel adapter, you don’t want anything blocking the electric current.
Specially, since it’s such a light current.
So perhaps electric grease is called for here. Conductive is OK since it’s only providing a ground path. And it’s only doing so when you push the horn button.
Obviously I don’t know what I’m talking about from any point of knowledge. So let’s wait for one of the resident experts to chime in.
Steve83 usually has opinions on electric versus dielectric grease.
Haven’t seen Steve in a while, in fact.
 

BroncoJimbo

Contributor
Long-term owner
Joined
Jun 11, 2014
Messages
291
Loc.
North GA
My Grant steering wheel set-up has a bushing/spacer between the hub and the circlip on the shaft. I'm not sure why since it doesn't seem to do anything.
I see you also suffer from the broken turn signal canceler common with the Grant hub. At least with mine anyways...
 

EPB72

Contributor
Bronco Guru
Joined
Jul 13, 2019
Messages
1,216
Loc.
Pleasant Hill, CA
My Grant steering wheel set-up has a bushing/spacer between the hub and the circlip on the shaft. I'm not sure why since it doesn't seem to do anything.
I see you also suffer from the broken turn signal canceler common with the Grant hub. At least with mine anyways...
the roll pins need to be bent to get the right clearence to stop braking the cancel cam ,,for lubricating the horn contacts Ford has electrical grease that works pretty good comes in a small tube ,, dieelectric can work as well
 
OP
OP
NJBronk

NJBronk

Contributor
Sr. Member
Joined
Oct 11, 2022
Messages
369
My Grant steering wheel set-up has a bushing/spacer between the hub and the circlip on the shaft. I'm not sure why since it doesn't seem to do anything.
I see you also suffer from the broken turn signal canceler common with the Grant hub. At least with mine anyways...

What is the bushing made of? I was thinking of using a washer to create some space between the outside collars. But thought that might crest friction there.

Yes, broken turn signal cam was why I have it apart in the first place…. Broke the pin when pulling off the old cam so trying some jb weld before buying a whole new switch assembly…. 🤦‍♂️
 

BroncoJimbo

Contributor
Long-term owner
Joined
Jun 11, 2014
Messages
291
Loc.
North GA
Here are pictures of the bushing I mentioned. I don't what it's purpose is or was. I bought my Bronco in 1990 and it already had a Grant wheel on it.
IMG_3892.JPG
IMG_3891.JPG
 

EPB72

Contributor
Bronco Guru
Joined
Jul 13, 2019
Messages
1,216
Loc.
Pleasant Hill, CA
Maybe you already know but when you put it back together wheels straight ahead the pins are centered between the cancel cam levers , so pins are oriented at about 9oclock,, if then possibly have to reposition wheel on adaptor not that your asking but I’ve corrected plenty incorrectly installed wheels on customer vehicles,,
 

BroncoJimbo

Contributor
Long-term owner
Joined
Jun 11, 2014
Messages
291
Loc.
North GA
Maybe you already know but when you put it back together wheels straight ahead the pins are centered between the cancel cam levers , so pins are oriented at about 9oclock,, if then possibly have to reposition wheel on adaptor not that your asking but I’ve corrected plenty incorrectly installed wheels on customer vehicles,,
Yeah, mine are correctly positioned. It's weird the cam breaks only on the bottom. The next one I get I'm going to file a little away from the top plastic piece because I think that is where the interference is. I built a clear plastic tool so I could see what was happening. From that I surmised the problem is the bottom part of the cancellation arm is closer to the pins than the top. That is what causes the bottom part of the switch to break and not the top. I think the next one I install I'm going to shave a little bit of the bottom arm, so it doesn't get caught.
 

Attachments

  • IMG_3899.JPG
    IMG_3899.JPG
    132.9 KB · Views: 115
  • IMG_3900.JPG
    IMG_3900.JPG
    129.3 KB · Views: 149
OP
OP
NJBronk

NJBronk

Contributor
Sr. Member
Joined
Oct 11, 2022
Messages
369
Actually, maybe not dielectric.
Reason being, since it will be a lubricant between the contact point and the copper trace on the back of the wheel adapter, you don’t want anything blocking the electric current.
Specially, since it’s such a light current.
So perhaps electric grease is called for here. Conductive is OK since it’s only providing a ground path. And it’s only doing so when you push the horn button.
Obviously I don’t know what I’m talking about from any point of knowledge. So let’s wait for one of the resident experts to chime in.
Steve83 usually has opinions on electric versus dielectric grease.
Haven’t seen Steve in a while, in fact.
Just to close this out, I picked up some carbon conductive grease on Amazon and used it on the little push button and ring. The annoying squeaking while turning is gone! Should have done it two years ago…
 

Rox Crusher

Bronco Guru
Joined
Dec 13, 2008
Messages
2,830
with wheels straight ahead, the pins are centered between the cancel cam levers, so pins are oriented at about 9oclock
Does everyone agree with this guidance, I was thinking the lobes on the cancel cam (or the pins if you're using an aftermarket set up) would be positioned at 3 to start?
 

Oldtimer

Contributor
Jr. Member with Sr. moments
Joined
Feb 4, 2005
Messages
1,801
Loc.
Sunnyvale, CA
Position at 9.
When going straight, you turn on Rt signal, can turn the wheel to the right, and pin will pass under cancel arm of switch (lifting it). When wheel comes back to straight, it will trip switch to off.
If pin is at 3 you would need to come back past straight (left turn) to trip switch to off.
 

kman67

Contributor
Full Member
Joined
Apr 8, 2005
Messages
180
Loc.
Aptos
I’ve got a Grant steering wheel as well and the horn contacts broke off and I got a new TS switch. Well the solder of the outside horn wire on the Grant hub was in the path of the horn contacts. So I resoldered it out of the way. I also checked the roll pin location using @BroncoJimbo plastic tool. First pic is the new and old Grant horn adapter, second is the resoldered horn wire. I also had my daughters help make the video and taught them how it works.
Kyle
ef3a029032c9c77b82bf47b6f913edb0.jpg


cb5101d0b605547f7f4fbc894ec6f4cd.jpg

f6eb384c953dcf7d1119d87ee61637a7.jpg



Sent from my iPhone using Tapatalk
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Don’t know if we’ve talked about it here or not, but you can probably add some life to the contacts by installing a horn relay in the system.
I did that to mine and everything just worked better.
Mine was a special case though, as I kept going wearing down the horn contacts and getting their ends built up with carbon so that at some point the horn would get a little bit erratic.
Guess I was a little too horn happy and a frequent flyer when it came to that.
Using a relay got rid of all that problem.

The new harnesses typically come with a horn relay conversion, but in case you’re still using the original harness, it’s a pretty simple process to add your own.
 
Top