• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Headers on 351w.

lewain

Jr. Member
Joined
Apr 28, 2019
Messages
95
I am thinking about putting some headers on on 1976 Bronco with a 351w, c4 automatic transmission.
Also, want them to turn out behind rear tires. Future will probably add an up graded fuel tank.
What is recommended and what should be addressed. ie,,,,starter clearance and over heating, brake lines, or any other clearance issues should I look at.
Also, what mufflers are easiest to configure? I have a set of cherry bombs on now with true dual exhaust
Or should I just stick with stock manifold with new system? Long tube or Short tube?
 

Jakedog

Bronco Guru
Joined
Jan 25, 2010
Messages
1,010
I ran a 351w in the 90's. I didn't have any clearance issues.
My exhaust was a single 3" pipe before the passenger right rear.
It was a 2 in 1 out flowmaster.
Amazing sound!
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,622
Loc.
PNW
I'm into performance and practicality... sometimes they don't mix well :) but hey- it's all fun!

Headers will introduce more heat into your floors and firewall. Probably the biggest down side of them over the stock cast iron flow reducing manifolds.

I fought heat for decades along with most everyone else who's installed headers. There are hundreds of posts here on ways to help address heat. Floor liner coatings, insulation, carpet, etc, etc, etc.

At one time or another I've tried most of them. Metal heat shields held off the body 1/2" from half way up the firewall to the back of the muffler work the best- bar none. Look at OE, they all use shields on mufflers.

Anyway- what's your goal for using headers?

Cherry bombs were the bomb of the '70's but they create a lot of back pressure and are obnoxious. There are lots of free flowing somewhat quiet or LOUD muffler choices. IF you drive this a LOT then my .02 is this, do NOT install flowmasters as the drone will drive you insane. It is obnoxious as heck. For a 5 min drive to the mall you can handle it. If you really drive your Bronco for an hour at a time at 60 mph you will wish you'd chosen something else.

I run big cams on big cubes and like a true dual exhaust. I can not fit a crossover in otherwise I would-literally no room and my exhaust is outside the frame anyway so it's really not worth it. I am fussy about exhaust and have lowered my floors, moved body mounts, etc so I can run free flowing mufflers and they are 50 % longer than typical UltraFlows- at 20" body length to help quiet the HP.

Brake lines and fuel lines MUST be rerouted to avoid issues. Go to a good custom exhaust shop and be there when they install it.
 

Glass Pony

Contributor
Bronco Guru
Joined
Feb 13, 2012
Messages
1,954
Loc.
Sussex County Delaware
I'm running long tube headers with the 351W, C-4, turbo mufflers, 2-1/4" dual exhaust exiting behind the rear tires.
The things I have and don't have help, like 2" body lift helps with clearance, not having an auxiliary tank helps.
I also run the 23 Gallon NWMP tank in the rear but the folks at the muffler shop was able to get around it.
 

mustanggarage

Contributor
Sr. Member
Joined
Aug 14, 2018
Messages
647
I highly recommend James Duffs ceramic coated long tube headers. I don't know what I did that has made the difference, but I used there ceramic coated headers with there true dual exhaust and magnaflow mufflers. I have a 2 inch body lift to clear things under the hood, I used bedliner under the body, and lizard skin heat shield, sound deadening and raptor liner on the inside of the bronco, I do not have carpet, just some floor mats but I get very little heat through the floor. I can comfortable drive barefoot if I want to. I have a bluprint engines 408 with sniper fuel injection. I suppose all the things together have made the difference, but in other vehicles I have built I can say that the ceramic coated headers do a lot to reduce heat under hood.
 

BroncoJimbo

Contributor
Long-term owner
Joined
Jun 11, 2014
Messages
291
Loc.
North GA
I have a 351W with old James Duff chrome headers that I've run for 22 years. I use a GR starter but didn't have any issues with the stock style. I run two Flowmasters with pipes exiting at the rear quarters. I don't have a problem with heat from the floor even though there is just Durabak with no carpet. As far as a drone with the Flows, not nearly as bad as my Mustang was with Walker turbos. No body lift, just the upgraded body mounts which is +3/4" IIRC. I love the way my Bronco sounds.
 
OP
OP
lewain

lewain

Jr. Member
Joined
Apr 28, 2019
Messages
95
I'm into performance and practicality... sometimes they don't mix well :) but hey- it's all fun!

Headers will introduce more heat into your floors and firewall. Probably the biggest down side of them over the stock cast iron flow reducing manifolds.

I fought heat for decades along with most everyone else who's installed headers. There are hundreds of posts here on ways to help address heat. Floor liner coatings, insulation, carpet, etc, etc, etc.

At one time or another I've tried most of them. Metal heat shields held off the body 1/2" from half way up the firewall to the back of the muffler work the best- bar none. Look at OE, they all use shields on mufflers.

Anyway- what's your goal for using headers?

Cherry bombs were the bomb of the '70's but they create a lot of back pressure and are obnoxious. There are lots of free flowing somewhat quiet or LOUD muffler choices. IF you drive this a LOT then my .02 is this, do NOT install flowmasters as the drone will drive you insane. It is obnoxious as heck. For a 5 min drive to the mall you can handle it. If you really drive your Bronco for an hour at a time at 60 mph you will wish you'd chosen something else.

I run big cams on big cubes and like a true dual exhaust. I can not fit a crossover in otherwise I would-literally no room and my exhaust is outside the frame anyway so it's really not worth it. I am fussy about exhaust and have lowered my floors, moved body mounts, etc so I can run free flowing mufflers and they are 50 % longer than typical UltraFlows- at 20" body length to help quiet the HP.

Brake lines and fuel lines MUST be rerouted to avoid issues. Go to a good custom exhaust shop and be there when they install it.

nvrstuk, you certainly make good points.
My mufflers now are actually “glass packs”.
I think that I am going to stick with true duels with new pipes and maybe some mild Flowmasters.
I recently put new high back bucket seats in. While waiting for delivery I removed the old seats.
New seats came in without the mounting brackets. So, while waiting on the brackets I thought why not do new carpet.
With carpet out I decided why not insulate. So, pulled out panels and headliner and insulated everything.
Made my Vintage A/C cool better even here in central Florida. with100 degree days.
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,622
Loc.
PNW
DynoMasters or UltraFlows ... anything but... and again just my .02 and anybody I've ever travelled with for more than an hour at cruising speed (like 35mph or more) but the drone on Flowmasters will drive ya nuts.

Chevelle's and Fairlanes can deal with the drone because you're literally 15' away from the tailpipes... lol
 

mustanggarage

Contributor
Sr. Member
Joined
Aug 14, 2018
Messages
647
To add to my earlier post. James duff offers there true dual exhaust with several muffler choices and they fit well. I really can’t recommend them enough they are the best name in bronco exhaust
 

bronco italiano

Bronco Guru
Joined
Feb 1, 2004
Messages
2,595
If you can source Doug Thorley headers I would go that way for two main reasons:
1- Probably best EB long tube every made quality wise
2- They carry the CARB compliant tag just in case smog becomes an issue

Regarding heat, and this is gonna sound ridiculous.
-Make sure the header is thermal barrier coated inside and out. Many headers are only outside coated.
-Have your entire exhaust inside/out thermal barrier coated, use v-band clamps at the muffler inlet/outlet. That was one of the best steps I took to get heat away from the engine.
-All the other items nvrstk stated are great additions
 

BroncoJimbo

Contributor
Long-term owner
Joined
Jun 11, 2014
Messages
291
Loc.
North GA
I highly recommend James Duffs ceramic coated long tube headers. I don't know what I did that has made the difference, but I used there ceramic coated headers with there true dual exhaust and magnaflow mufflers. I have a 2 inch body lift to clear things under the hood, I used bedliner under the body, and lizard skin heat shield, sound deadening and raptor liner on the inside of the bronco, I do not have carpet, just some floor mats but I get very little heat through the floor. I can comfortable drive barefoot if I want to. I have a bluprint engines 408 with sniper fuel injection. I suppose all the things together have made the difference, but in other vehicles I have built I can say that the ceramic coated headers do a lot to reduce heat under hood.
It's odd the James Duff listing omits 76-77 Broncos. I was checking since my old Duff's headers are getting a little crusty.
 
Top