• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

HELP!! My Bronco won't stop clicking!

75broncokid

New Member
Joined
Dec 3, 2005
Messages
7
when i turn it over, i get this really irritating rapid clicking sound.
i've got a brand new battery, new starter solenoid, new battery cables, clean connectors and still getting the clicking.
ive checked the cables, grounds etc. and the connections are all clean.
it was running great for about a week when i got it out then this started happening.
i tries giving it a jump today aswell and it wouldnt even turn over....?!?!

any ideas out there??

thanks
 

Jeepster

Bronco Guru
Joined
Jul 13, 2001
Messages
1,507
Sounds like a classic low voltage situation. Reading I see you replaced just about everything pertaining to starting. I would first see if the motor will turn over by hand,with a socket/breaker bar....hey you never know, maybe engine seized up.....then I would meter all connections starting with one lead at the battery and move the other lead to each connection to check for voltage drop. This will help double check the new cables for breaks. Remember, just because its a new part dosent mean its good. ;)
 

mtkawboy

Bronco Guru
Joined
Jan 28, 2004
Messages
1,525
Loc.
Billings Mt
Id try jumping across the solenoid first then proceed to the breaker bar if battery voltage is good. Maybe take the plugs out & try it in case theres a cylinder full of coolant before you bend a rod. Yes they will most definetly hydraulic and bend a rod, Ive seen it.
 

Skuzzlebutt

PhD, Dr. of Broncology
Joined
May 26, 2001
Messages
4,393
Loc.
Honeymoon Bay
It's voltage, or amperage, or you just got stuck with a faulty new solenoid.
If the engine, or starter, were siezed, the solenoid would still give only one solid click if the electrics were all good.
If the ground isn't adequate, a test light or volt meter may show 12+ volts but that doesn't tell you diddly about the amps getting thru.
I'd try running a small ground wire directly from tha Bat to the solenoid.
 

oh2bnok

Bronco Guru
Joined
Jan 28, 2004
Messages
1,098
Loc.
Olathe, KS
Is your ground cable from the battery to the block new ? If not it is possible the ground cable is corroded/cracked inside the sleeving. I would put on a new one.
 
OP
OP
7

75broncokid

New Member
Joined
Dec 3, 2005
Messages
7
so today i replaced the battery cables, wire brushed all the connectors etc.
nothing.
then i tried to jump it, now it wont even turn over with a jump (it used to start with a jump no problem), then i tried jumping it by passing the solenoid and got a nice big spark but no crank at all.
what the hell is going on, everything was fine last week now everything is going to shit!

my bro thinks because i got no crank that the starter is shot....

anyone??


thanks
 

RajinCajun

Bronco Guru
Joined
Nov 22, 2003
Messages
1,587
Loc.
HawleyTX, La orig.
LIke stated previously, see if it will turn over by hand with a breaker bar.. If it does, pull the starter and use a set of jumper cables and connect them directly to the starter and a good batt... just touch the ground on the starter it should turn over as normal...if not the starter is bad.. Good luck.. Oh, don't create sparks at the batt while doing this test....not good.
 

bax

Contributor
Old Member
Joined
Aug 22, 2005
Messages
14,552
Check the starter solenoid, is it a 12 volt solenoid? they make 24 and 36 volt solenoids. Both will act (Clicking) with only 12 volts to them. If that checks out I would check the starter next as already stated.
 

76Broncofromhell

Bronco Totalitarian
Joined
Jul 30, 2001
Messages
4,250
Loc.
Grass Valley, CA
Check the surface where the solenoid mounts. The starter solenoid is just a big electromagnet with a spring, so when the ground connection of the solenoid is poor, it has trouble staying closed when you apply electricity to it.
 
OP
OP
7

75broncokid

New Member
Joined
Dec 3, 2005
Messages
7
hey thanks for all the help, i appreciate all the thoughts. i wont have a real good chance till wednesday to get at it again. gonna spend the whole day going through everything you guys have said.
any other thoughts though id love to hear em.

i got a 75 bronco, 351w, new headers and flowmaster mufflers, real nice purr when shes running well. i miss that sound especially when it sets of car alarms and freaks out the neighbors....im sure most of you share that feeling too.

thanks again.
 

Wes harden

Jr. Member
Joined
Jun 5, 2005
Messages
111
starter draw

You may have a bad armatur in the starter drawing to much current, and cuasing a low current condition for the solenoid. A voltage drop test will show the conditions of you cables and conections, as Jeepster suggested. You will need a 600 amp meter to check the the starter draw (ie Vat 40). Also do try turn it over by hand quick easy check.
Had a pep boys rebuilt dead short on me once, 2 weeks old. the idot triple A guys, I called to tow me home, had 3 trucks hooked up to my batt at 1 point. Then they procceded to stand over the batt while I hit the key. I'm sure glad my batt didn't blow up or I would have never been towed, 3 injured tow truck drivers. So be weary of those new rebuilts they may not even work 1 time.
 

Gummi Bear

Bronco Guru
Joined
Jul 8, 2003
Messages
3,647
Is the clicking just during the starting, or right after it starts? A bad/ mismatched PCV can click and drive you bonkers too. It's an easy and cheap fix too. You may want to also keep that in mind.
 
OP
OP
7

75broncokid

New Member
Joined
Dec 3, 2005
Messages
7
it was clicking just when i turn the key, if it started it ran fine, the only thing i noticed is the turn signals would flash quicker when it was running then when it was off.

now it wont do anything, like ive said ive replaced everything short of the starter, on wednesday ill have the whole day to go over it with a meter to see about voltage etc. but im not much of an electrical guy.

my bro seems to think since i tried all the tests that my starter is shot. my bronc went through a 2.5 yr restoration, new everything, except i left most of the engine because it was running fine before, started on a dime.
 

Jeepeater

Sr. Member
Joined
Aug 10, 2005
Messages
352
I had the same type of problem. 1st t ime it was my starter. replaced it, and all problems were fixed. This year I went to start her up and It was clicking. It had a new battery, I couldn't figure t out. Well it was my brakelight switch on the pedal that was stuck, and drained my battery completely. I finally got it charged enough to get it started.
 

Hazegray

Sr. Member
Joined
Aug 10, 2004
Messages
795
If the headers are a new addition & the problem showed up after installation, then it could be a heat-related starter failure. After installing headers in my 69 'stang, I would go through a starter every 3 mos! Finally wrapped that sucker in a heat shield, problem went away after that.
 

RRRAAAYYY2

Bronco Guru
Joined
Nov 10, 2004
Messages
1,684
Loc.
Brantford, Ontario
Call me when you go to do the tests. Have a booster cable ready, and a volt meter. If you can put your battery on a charger today, so that way you know it is fully charged. If there is someone that can help you that would make things a lot easier.
1-888-214-7774.

Also if you go to my website and then FAQ page, go to voltage drop testing, it is very simple and I expect you will find tons of issues throughout your vehicle. Most everyone does.
 
OP
OP
7

75broncokid

New Member
Joined
Dec 3, 2005
Messages
7
about the headers when i installed them i wrapped them aswell just in case of any heat related issues.
my bro is over tomorrow morning and we will be doing a full diagnostic on the engine form the battery all the way through. he's got a jump kit and a meter so hopefully (cross my fingers) we'll figure it out.
also i realize after sitting so long (2.5 years) getting a full makeover on the body and interior when i got it out it on the road makes sense that everything is gonna be shaken up a bit and these problems are part of the process. a process that when my bronco is running makes all the bloody knuckles and sweat worth it.
 
OP
OP
7

75broncokid

New Member
Joined
Dec 3, 2005
Messages
7
Well my bro came over this morning and we got to it.
when we put the meter on the battery it showed it was almost dead, it was making a horrible sound when you cranked it but we actually got it started with a good jump but the battery was losing the charge from 11v to 10 to 8 etc..

ruled out the starter, the new solenoid i got was actually messed up so put the old one back in, new battery cables were also not needed.

went and grabbed a new alternator ($80) and new voltage regulator. installed those two and still nothing. battery was still losing charge so my bro was like "wheres the fuse box?" i have the centech harness so it in the glove box, well the alternator fuse was blown, replaced that and guess what? battery is still pretty low, but alternator is charging it nicely, took it for an hour long cruise and now it starts on a dime, idles nice and way better power to the lights etc.

so heres my little list

NOT NEEDED BUT BOUGHT:
new battery $90
new battery cables $45
new solenoid $22
new voltage regulator $20

DIDNT REALLY NEED BUT DOESNT HURT:
new alternator $80

ONLY THING I REALLY NEEDED
fuse $1

thanks for all the ideas though. when she lit up that sound just warms my heart....
 
Top