• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

High idle and other issues

kaw550

Bronco Guru
Joined
Jul 4, 2007
Messages
1,136
My Bronco came with an Edlebrock 1405 on a Weiland intake.

I can't seem to get the idle down low enough. It is idling at around 1,000 RPM but will not go lower. I rebuilt the carb and just installed smaller jets and rods.

I plugged the PCV port on the front of the carb, not sure if it makes a difference.

I tried checking for a leak but could not find one.

It seems to run okay but there is some noticeable smoke from the exhaust, strong fume smell and occasioning popping from the exhaust.

Do I have engine problems or tuning issues?
 

t.lay

Bronco Guru
Joined
Mar 17, 2005
Messages
1,261
Loc.
Grayslake, IL
I had idle problems - turned out the dizzy wasn't buttoned down - so idle bounced all over the place. I still get fumes though - got an elec fuel pump - wondering if I'm getting too much gas to the carb??? Hoping some of the engine gods can answer.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Sounds like you got a couple of problems. 1 a vacuum leak somewhere it could be anywhere manifold, carb, vacuum line ect. I'm not really familiar with Edelbrock carbs but check to make sure the secondary throttle plates are fully closed some carbs have a adjustment. If they are open they will cause the high idle. As check the timing as others suggested.
2 smoke and fuel smell usually points to a fuel leak float set to high? might want to recheck. make sure fuel is not dripping into the manifold while idleing. What color is the smoke? Smoke can also be caused by incorrect timing.
 
OP
OP
kaw550

kaw550

Bronco Guru
Joined
Jul 4, 2007
Messages
1,136
I checked around the carb but not the manifold. I will check that next.

There is not much left to check for vacuum lines. I think they have all been removed. I basically have one from the carb to the distributor.

I did go though the timing a few weeks back. It should be set to 8 degrees.

On the valve cover I have a 45 degree elbow with nothing connected to it.
I did buy a PCV but I have not put it in yet.

The smoke looks white. There is not a lot.
 
OP
OP
kaw550

kaw550

Bronco Guru
Joined
Jul 4, 2007
Messages
1,136
I was just checking out an oil leak coming from the dipstick tube. It seams to be oil mixed with either gas or water.

Is there an easy way to tell? It did not smell like fuel, not sure if it would.

I am trying to decide if it is a carb issue or with the intake.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Ditto
You could pull the oil drain and see if water comes out it will come out first as the oil floats on water.
 

PaulS

Jr. Member
Joined
Dec 6, 2007
Messages
96
Loc.
Greater Seattle area
It sounds like the high idle screw (for the choke system) or the curb idle solenoid (if so equipped) need to be adjusted. Since you just rebuilt the carb the diagram should show where these items are. Check to make sure the linkage is not holding it open too - just disconnect the linkage and see if the idle drops. If it is the linkage there should be a way to adjust it so you can idle it down either where it mounts to the manifold or firewall.
 
OP
OP
kaw550

kaw550

Bronco Guru
Joined
Jul 4, 2007
Messages
1,136
still rich

Tonight I put in fresh plugs and looked over the carb (edlbrock 1405). The linkages looked fine so I started it up and let it idle for for 15 to 20 minuted. I turned in the idle scews to make sure it was as lean as possible and still would idle.


With the idle screw all the way out it wont go below 900-1000 rpm.

I checked the plugs after and they were black (soot).

At the same time I connected a vacuum gauge. It was a steady 15 hg (timing set to 8 degrees). I did advance the timing a little and it was steady at 18. I had to connect it to the port on the carb. Tomorrow I will add a port to the manifold and try again.


I can understand how a leaking intake would cause a high idle but would it cause the plugs to be black?


The carb has been set to two stages lean according to the edlbrock manual
 
Last edited:
OP
OP
kaw550

kaw550

Bronco Guru
Joined
Jul 4, 2007
Messages
1,136
I checked. The high idle screw does not touch at idle. I even took off the linkages to confirm the pedal assembly or choke wasnt holding it open.

At what rpm does it get past the idle circle?
 
OP
OP
kaw550

kaw550

Bronco Guru
Joined
Jul 4, 2007
Messages
1,136
Any chance the stock fuel pump is putting out to much pressure?
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Shoundnt be have you looked down the carb when running to see if there was any dripping?
I would probably pull your carb off and look closely at it while off to make sure the throttle blades close all the way then reinstall and make sure they are still close all the way also might want to make sure they open all the way. Sometimes some manifolds or gaskets need to be clearanced so the linakage clears and doesnt bind or get hung up.
 

PaulS

Jr. Member
Joined
Dec 6, 2007
Messages
96
Loc.
Greater Seattle area
Are the secondary throttles closed at idle?
If not that would cause a high idle and lack of idle fuel mix adjustment.
Did you install the spring correctly when you replaced the rods? Are you sure the rods are in the jets? Did you do anything to the idle air or main metering air bleeds?
In order to run at high idle it has to be getting air and fuel - a lot more than when it idles. It has to be getting the air through a leak or the throttle plates. It has to get fuel from some place too. It could be a misplaced or torn gasket or through the main metering circuit.
 
OP
OP
kaw550

kaw550

Bronco Guru
Joined
Jul 4, 2007
Messages
1,136
I was wrong. Only a few of plugs were fouled. Basically the middle two on each side.


I did find an air leak on either the intake or the carb. I need to cover up the intake on the left side so I can spray just the carb.

Would a leaking intake cause some to be rich and others to be normal?

I did install a fuel pressure gauge and an vacuum port, everything tested fine.
 
Top