• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Holley Carb setup

Seventee

Contributor
Sr. Member
Joined
Dec 7, 2012
Messages
999
Loc.
In the sticks of MT
Based on what you are describing, I also suspect that your accelerator pump is not working correctly. That might explain some of the bogging and backfiring you are experiencing.

Even with a lean or inoperative choke, under most circumstances you should still be able to pump enough fuel into it using the pedal to get it to fire.

Look down the carb throat while you work the throttle linkage by hand. You should see two steady streams of fuel squirt into the bores when you pump it.
 

72_EB

Contributor
66to77
Joined
Feb 4, 2003
Messages
4,982
A couple base measurements might be very helpful in determining your issue.
What is your initial timing set at? What is your vacuum reading when truck is at temperature at a standing idle?
You can't really guess what your timing is set at without checking it with a timing light. You can listen for pinging and detonation, but really better to know where you at with an accurate instrument reading. Buy a timing light if you are going to be working on it. If you're backfiring at all, you need to check your timing. You may be running rich because you blew a power valve in the carb. This is rarely happens, but it does happen.
A vacuum gauge is also a very good tool to have as well. A good carb mechanic can adjust idle mixtures screw by listening to the sound of the motor, but a vacuum gauge makes this procedure much easier and accurate.
This is engine timing and carb adjustment. There may be other issues going on if the previous mechanic was using glass filters, installing the carb without a good gasket or insulator, failed to tighten hoses and the carb is sucking air, a failing gas cap. Refreshing to see someone with enthusiasm to work a carb, but check all the your basics first before messing with the idle mixtures screws. This will be pretty much your last adjustment.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
Would you like a better ignition? For free?
Your choke is killing spark.

That red wire from the starter solenoid to the choke, move it to the "STA" terminal on the back of the alternator.
The choke is putting an extra load on the ballast resistor. Causing more than engineered voltage drop to the coil.
The choke will get about the same voltage, but only get it when the engine is running and not just when the key is on so that is better engineering as well.
 

Seventee

Contributor
Sr. Member
Joined
Dec 7, 2012
Messages
999
Loc.
In the sticks of MT
Would you like a better ignition? For free?
Your choke is killing spark.

That red wire from the starter solenoid to the choke, move it to the "STA" terminal on the back of the alternator.
The choke is putting an extra load on the ballast resistor. Causing more than engineered voltage drop to the coil.
The choke will get about the same voltage, but only get it when the engine is running and not just when the key is on so that is better engineering as well.

Good catch! Definitely need to move that wire.
 
OP
OP
jasonmcc

jasonmcc

Sr. Member
Joined
Dec 1, 2018
Messages
395
Loc.
Nola -> Utah
Moved it...
fe665e90af88e44bbc61afdcdfbf475f.jpg
b4a132e9f040518a22abd35531907179.jpg
f99dcf0c0d42aa9f632cd4b7e453e210.jpg
acd3782704fd0e07f3833c5d7e2d88c5.jpg



Sent from my iPhone using Tapatalk
 
Top