• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Just my luck

Bdhand

Contributor
Sr. Member
Joined
Aug 15, 2015
Messages
712
So I'm working on my 66 bronco and currently I am installing a disc break conversion on the front with booster. PO told me that the only thing that needed to be done to the rear drum breaks is the wheel cylinder's need to be replaced. Took the drums off this evening to replace the cylinders and guess what.... Drum breaks are SHOT!!! So the question is since I have to spend money on the rear breaks do I go ahead and put disc on them or go back with drum. I haven't compared the prices yet. Decisions decisions.....
 

hucklburry rev2

Sr. Member
Joined
Jan 17, 2006
Messages
772
I just did the rears on a 66 with 11" brakes, I didn't need new drums, so I had less than $100 in it, wheel cylinders, shoes, spring kits, steel lines, I also got a new hose up to the frame, extended rubber one I found referenced on here.

You have a 6cyl like I do, I put discs on the front, I don't think I need rear, I stayed manual as well. I run 31" tires, its a grocery getter toy.

If I do a 250/turbo with a 5 speed, then I do plan on getting rear discs and some other stuff, but with this 170 I don't see the need right now. I did install a proportioning valve in-line to the rear so I can dial it in once its running better (just took its first spin in 10 years this past Saturday)
 
OP
OP
Bdhand

Bdhand

Contributor
Sr. Member
Joined
Aug 15, 2015
Messages
712
I just looked at the cost to upgrade to disc on the rear and it is more than I thought. So I'm thinking that I will stay with drum. How do I tell if I have the 10" or 11". I'm thinking that I need to measure the diameter of the break drum! Is this correct?
 

hucklburry rev2

Sr. Member
Joined
Jan 17, 2006
Messages
772
I measured the width of the pad on the shoe. 10" is 2.5" wide, 11" is like 1-3/4" wide, pretty easy to tell that mine weren't 2.5" wide.

Mine was 11", it has the 3300# axle, I don't know if those correlate or not.
 

suckerpunched

Sr. Member
Joined
Aug 24, 2006
Messages
882
measure I.D. of the drum. it will be 10" or 11" yeah the 11" brakes are better, if you have a set laying around great but if not I would rebuild the 10's and call it good. The drum brakes are pretty cheap to replace.
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
measure I.D. of the drum. it will be 10" or 11" yeah the 11" brakes are better, if you have a set laying around great but if not I would rebuild the 10's and call it good. The drum brakes are pretty cheap to replace.

You can't just swap from 10" to 11" brakes. The backing plate bolt pattern is different and the axle shafts have a different brake offset. It would be much easier to swap the entire axle out.
 
OP
OP
Bdhand

Bdhand

Contributor
Sr. Member
Joined
Aug 15, 2015
Messages
712
Looking at my rear brakes mine does not have the self adjusting kit on them! Can that be added or do I need to leave it off?
 

AWS

Sr. Member
Joined
Aug 2, 2004
Messages
596
Loc.
ST LOUIS
When you get your brake shoes just pick up some self adjusters at the same time. I put them all the way around on my daughters 66 U13.
Steve
 

AWS

Sr. Member
Joined
Aug 2, 2004
Messages
596
Loc.
ST LOUIS
I just did the rears on a 66 with 11" brakes, I didn't need new drums, so I had less than $100 in it, wheel cylinders, shoes, spring kits, steel lines, I also got a new hose up to the frame, extended rubber one I found referenced on here.

You have a 6cyl like I do, I put discs on the front, I don't think I need rear, I stayed manual as well. I run 31" tires, its a grocery getter toy.

If I do a 250/turbo with a 5 speed, then I do plan on getting rear discs and some other stuff, but with this 170 I don't see the need right now. I did install a proportioning valve in-line to the rear so I can dial it in once its running better (just took its first spin in 10 years this past Saturday)

Jim, I thought this bronco was for Hunter!
Steve
 
Top