• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

LOWERING my Bronco

OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
:cool: I got off the phone with Van from Tumblin Auto. They have a great 4.6 DOHC conversion article in the new Bronco Driver magazine (p.25-27), and an ad on p.79. I got his info from dnewman9 (thanks Dennis!) about the 4.6 DOHC mod motor conversion. I pulled the trigger and ordered a set of his motor mounts, and custom headers for the 4.6. Now I wonder...is it going to be a LONG or a SHORT winter? %)
 

Heus33

Bronco Guru
Joined
Jun 1, 2005
Messages
7,488
What are your plans for bumpers? Ever think of a roll pan in the back?

Actually what about finishing off the bottom portion of the front grille and running "bumperless"? I've been thinking about this a lot lately - wonder if anyone has tried this...
 
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
Here is my drawing of what I am going to do with my front valance, adding fog/running lights. I am going to use the same rear roll pan you used, welding in Mustang Mach I exhaust openings.
 

Attachments

  • CUSTOM%20VALANCE.jpg
    CUSTOM%20VALANCE.jpg
    120.8 KB · Views: 111

behemoth

Bronco Guru
Joined
Jul 2, 2003
Messages
1,736
I have been thinking of narrowing the front bumper, as well as tilting it slightly at the bottom. Just enough to alter the brick look.

The c notch kit the rear lower edge is level with the bottom of the frame. The sides need to be trimmed like the one piece was. The top was trimmed to fit my truck should work on yours. The inside plates will need to be trimmed we used a small t square to line them up. They are centered on the desired axle location, I moved mine to the rear. It is to the rear so that the rear differential just clears the rear crossmember at full compression.
I can get the measurement for my rear axle center line this weekend.

Axle center plates? you going to use leafs or something else ?
 
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
I am using the original leaf springs. It turns out that the Explorer rear end housing is the exact same diameter as the HD 76-77 9 inch rear. I picked up two sets of those retaining plates (thanks again NicksTrix) , and ordered a new set of U bolts. Hopefully the frame is done today when I go to check on it in a few. Then I can start cutting, grinding, and welding on it. I will be sure to take a few pics!
 
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
I won't bore you with pics yet. We just got back in the house after etch priming the frame. The wife helped me spray and flip the frame. Not bad... just before we go out for our anniversary dinner! Her training is almost complete! Thank you honey!
Next week my buddy is going to have his '34 Ford back together after the paint job. That will make room in the shop for the frame and we can get started. I will be sure to take pics then so you can all watch as we cut and chop the items off that will no longer be needed. Then we move on to the Mustang II install. One thing at a time....for now.
 

Heus33

Bronco Guru
Joined
Jun 1, 2005
Messages
7,488
Here is my drawing of what I am going to do with my front valance, adding fog/running lights. I am going to use the same rear roll pan you used, welding in Mustang Mach I exhaust openings.

Thats gonna look great! I've got the part number for that roll pan if you need it.
 

Heus33

Bronco Guru
Joined
Jun 1, 2005
Messages
7,488
Here is my drawing of what I am going to do with my front valance, adding fog/running lights. I am going to use the same rear roll pan you used, welding in Mustang Mach I exhaust openings.

I've been thinking about this for awhile now and did some measuring this weekend. How do you plan on completing that front facia? If you follow the contours of the front grille and complete the bottom half of the grille you'll run into the frame horns. It looks like they stick out a good 3 or 4 inches. Are you planning on cutting the frame horns?

I've got a line on a used grille and I might use as my template but I'm nervous about cutting the front frame horns. Are you ready for that commitment!?!
 
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
Here is the newest pic of Dale's ride. It is pretty close to what I will be shooting for as far as looks. I was thinking Acupulco Blue for my project though, or a green maybe?
 

Attachments

  • 100_1267.jpg
    100_1267.jpg
    52.2 KB · Views: 314
  • DSC00878.JPG
    DSC00878.JPG
    37.1 KB · Views: 281

behemoth

Bronco Guru
Joined
Jul 2, 2003
Messages
1,736
I would like to see an engine compartment pic or two as well as a picture of the steering column to steering rack.

looks really good, I was thinking of a narrowed eb front bumper and the 69-70 mustang front spoiler air dam.
 

Tito

CB Fire Starter
Joined
Jan 29, 2006
Messages
10,781
Loc.
Bakersfield, CA
Marty, that thing is pretty! I actually really like the front bumper, especially for us states where we are required to wear a front plate.
 

Heus33

Bronco Guru
Joined
Jun 1, 2005
Messages
7,488
hmmm im a bit dissapointed with the front valance (just my opinion though). Looks like a rear bumper to me. I hope you stay true to your sketch above. Gotta do something with those frame horns - they can't stick out that far.
 
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
I totally agree. Trust me, I will be sticking close to what the pic shows. I would like to keep the license plate low and centered. I would get rid of it entirely if I could, but state law here says you have to run a front plate. Hopefully I will have pics of my project moving forward here soon. I will be using the same rear roll pan that you have in your avatar Heuss33, but mine will have the license plate centered. I am pretty anxious to get going now!
 

behemoth

Bronco Guru
Joined
Jul 2, 2003
Messages
1,736
Marty,
On that notch kit look at cutting 1/4 off of the top to lower it. Mine is right at the bottom of the body now and a little more room could not hurt.

Also ask Dale about the leafs he used, the costs associated with 4 link and bags will be more than custom leafs.

4 link for a lifted truck is easier than on a lowered one that you want to keep the bed complete.

Lots more to think about.
 

ugly74

Bronco abuser
Joined
Apr 17, 2006
Messages
2,856
Loc.
Colorado
state law here also says I hafta have a front plate. but I don't have one on any of my cars, and I've only been pulled over once, in 16 years for it. $25 fine is a small price to pay to keep the lines ya want says I
 

Heus33

Bronco Guru
Joined
Jun 1, 2005
Messages
7,488
state law here also says I hafta have a front plate. but I don't have one on any of my cars, and I've only been pulled over once, in 16 years for it. $25 fine is a small price to pay to keep the lines ya want says I

There are two roll pans you can use - one has the frenched licence plate and the other has no plate. If you go with the frenched version there's no turning back but if you use the flat version you can get creative with your licence plate mount making it as permanent or temporary as youd like.

It'd be cool to have a removeable frame held on by magnets or something - this way you could remove it at shows or whatever and pop it back on for the drive home.
 
Top