• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

LOWERING my Bronco

77bronco_ed

Bronco Guru
Joined
Jul 3, 2004
Messages
1,793
Well Jami dropped it off this moring. Had to do some running around BUT I still managed to strip it all down. Maybe I should have looked it over a better. I may have more than I can handle. This will require a lot of work. The nice outside is very deceiving. All welded to the only remaining pieces of metal left that you can call inner. Yikes...

no inner rockers, floor braces and the list goes on...

Hopefully he will make it over tomorrow morning to pick up the axles wheels, and all of the other parts. My neighbors will not like to see it laying in the driveway ;)

I think I will start another thread... It is going to be a long build.
 
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
Ok so I am a little slow with my progress lately. I have the A arms modified to accept the QA1 coilovers. I had them welded up and cleaned up the welds a little(yeah I am picky). I then dropped them off at the blasters (picky) after work. I will have the tubes trimmed out and ready to fit the coilovers tomorrow, then do a little touch up paint to make them shine. I will be sure to post a few pics of what I had to do to make the coilovers bolt up. I should have the front end bolted together by the weekend. It will still be just a rolling chassis with the engine and trans, but hey....it's progress! :cool:
 

77bronco_ed

Bronco Guru
Joined
Jul 3, 2004
Messages
1,793
project work day 1...
Tear apart, once I lift the body off I will remove the trans and transfer case from the frame. It will stay for a bit.

project work day 2...
Braced rear, and began rear floor rust removal.

My project grew 200% by using this tub... If I can pull this off I'll impress myself.

oh... and the pictures make it look much better than it really is...
 

Attachments

  • bed1.jpg
    bed1.jpg
    54.4 KB · Views: 103
  • front inners_1.jpg
    front inners_1.jpg
    48.6 KB · Views: 98

77bronco_ed

Bronco Guru
Joined
Jul 3, 2004
Messages
1,793
QUOTE=behemoth;1692259]I would raise the rear bed floor about 6 inched to keep it flat with a good C notch underneath it.

I will go forward and modify the front floor pans (lower) However since I am tubing the truck the rear wheel wells will be much wider I will make the wide enough to hide the channel
Quick photoshop pic to give you an idea on what I am going for...most likely wider than what i have shown.

modified_bed.jpg [
 

Attachments

  • green_unmodified.jpg
    green_unmodified.jpg
    67.4 KB · Views: 54

behemoth

Bronco Guru
Joined
Jul 2, 2003
Messages
1,736
I had thought about widening the wheel tubs, but it was quickly pointed out that I would also need to clear the rear center section. So the whole bed floor will either come up or just modded to clear the bigger notch if I do it.
 

77bronco_ed

Bronco Guru
Joined
Jul 3, 2004
Messages
1,793
I had thought about widening the wheel tubs, but it was quickly pointed out that I would also need to clear the rear center section. So the whole bed floor will either come up or just modded to clear the bigger notch if I do it.

How much have you lowered yours from the original stance...(inches)
How much clearance do you have from the floor to the rear center now?

It sounds like you have lowered it to the maximum amount without bed modifications correct?

Thanks,

-Ed
 

behemoth

Bronco Guru
Joined
Jul 2, 2003
Messages
1,736
With the rear on the bumpstops I have 1/2" between the center section and the bed floor. The bed is untouched as is the floor supports.

I did not take any measurements of ride height before I can tell you that the front bumper( stock ) is 7" off the ground and the rear is about the same when bottomed out.
 
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
Well I spent alot of time after work redoing the A arms I have. These did not have the tubes welded in for the coilovers, and I did not want to shell out another $300 for the new arms. I had to trim out the spring buckets on the mill, and then mill a slot across the hole for the tube to seat into.
 

Attachments

  • LOWER ARM 1.jpg
    LOWER ARM 1.jpg
    191 KB · Views: 45
  • LOWER ARM 2.jpg
    LOWER ARM 2.jpg
    143.9 KB · Views: 46
  • LOWER ARM 3.jpg
    LOWER ARM 3.jpg
    43.8 KB · Views: 49
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
Here is what they look like trimmed out and the tube spot welded in.
 

Attachments

  • LOWER ARM 5.jpg
    LOWER ARM 5.jpg
    46.1 KB · Views: 55
  • LOWER ARM 4.jpg
    LOWER ARM 4.jpg
    47.5 KB · Views: 47
  • LOWER ARM 6.jpg
    LOWER ARM 6.jpg
    200.2 KB · Views: 72
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
I tapped one end of the tube and drilled and reamed the other end with a .500 reamer. I notched one short piece to weld to the outside of the arm for the bolt head to seat up against. You can see that these bosses are missing in the first two pics, and see one clearly in the last pic.

After welding them in whole to keep them straight through, I precision milled the centers out and trimmed the outside edge off so all the ends of the tubes stayed parallel to each other.

If I had it to do over again I would have had them TIG welded, but I had access to a MIG so I used that. I had alot of cleaning up to do and then had them blasted. TIG would have been so much cleaner!
 

Attachments

  • LOWER ARM 7.jpg
    LOWER ARM 7.jpg
    240.9 KB · Views: 48
  • LOWER ARM 11.jpg
    LOWER ARM 11.jpg
    240 KB · Views: 47
  • LOWER ARM 12.jpg
    LOWER ARM 12.jpg
    54.8 KB · Views: 41
  • LOWER ARM 14.jpg
    LOWER ARM 14.jpg
    52.5 KB · Views: 51
Last edited:

77bronco_ed

Bronco Guru
Joined
Jul 3, 2004
Messages
1,793
Control arms look nice... So it was a bunch of trouble getting the right coil springs?

I'll have to go back and look over the thread.
I have not worked in the shop for about 20 years. It was nice having access to all the equipment. If I need to make mods it will be with a scale and a fiber cut off wheel :)
 
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
Length and spring rate. As long as someone else has already done this and can offer their input, you would have no problems. If you go to the "street rod" experts, they can only guess as to what kind of ride and at what height your vehicle would end up setting at. It also depends on what engine/trans combination you are going with.

With the coilovers you not only have ease of installation, but also some adjustment to the ride and height as well. That is what I have found, and I am sure Bill (behemoth) would tell you the same. Now Dale (another Bronco rod guy in Wisconsin) set up with the whole front end kit from Heidt's, and used his 302 and a c4 I believe. He loves the ride and handling the last I heard, but not sure is he was satisfied with the rake he ended up with.
 

behemoth

Bronco Guru
Joined
Jul 2, 2003
Messages
1,736
I tried the springs that came with my heidts kit as well, they were for a truck so they were rather stiff. They did not budge with me on the bumper so that would not work.

I then borrowed a friends scales to weigh it to get the correct spring rate for the coil overs. 600lb spring rate for coil overs.

The truck springs were 300lb rate.

the truck weighed in at 2920lbs and somewhere in this thread is the front and rear axle weights. I have since lightened the truck by removing the heavy bench seat, window frames, and windows.

Those arms look great,
 
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
Actually I have been working my (_!_) off lately. I am so tempted to go out and install the arms, but it is 25 degrees here today and I have no heat in my garage yet. Of course the fact that my S10 rear axle took a crap to the tune of $1400 doesn't help me out either. At least at 25 degrees my beer can't get warm!;D
 

77bronco_ed

Bronco Guru
Joined
Jul 3, 2004
Messages
1,793
I hear that... a couple years ago I was bummed about no heat. I got a free furnace from a friend, after looking into it I did not want to run a giant stack on top of my garage.
I found a 90% furnace on craigslist for $75. (nice because combustion is sealed, and uses outside air) Cut a couple holes in the side of my garage and ran some gas pipe. Made it as safe as possible reading up and trying to follow code for placement, intake, exhaust, etc.. I plan on pulling it out if I move. I leave it on low 40-45 unless I am in the garage heats up in about 3-5 minutes.

It really is nice having heat in the garage.
 
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
Ok seeings how this will be my 2000th post it seemed fitting that I post here. It is colder than...well you know. I didn't even bother to shovel until it actually stops blowing snow here. The good news is we have decided (thank you wifey!) to install a garage heater next week. Yeah it's just a tad bit cold here in South Dakota lately.

With heat and 10 days off in a row over the holiday I should be able to get things done. At least enough to post pics and get my blood flowing for this project again. Don't get me wrong, it's not that I haven't been plotting and planning. I have all the parts to get the front end together and hope to get the tub off the old frame and onto the lowered version so we can get a peek at what this beast will look like in the future. I will also see if I have the rear axle clearance problems Bill has been looking at lately.

Anyways, stay warm out there in Broncoland wherever you are!:cool:
 

77bronco_ed

Bronco Guru
Joined
Jul 3, 2004
Messages
1,793
Heat... Great news! you can work when it is cold and nasty outside and then enjoy the summer ;) Hopefully you and Bill will keep moving along experimenting working out the bugs. Your progress is very motivating for me, it will keep me going on my own project. I like the fact that you guys have already ran into issues and can help ease or avoid problems that we could or would have encountered.
 
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
That is what is so cool about this site. Along with the wealth of info from all the Bronco guys here, we have a few of us doing what some might think is insane. I personally would love for all these street rod projects to meet up sometime next summer at one of the Bronco events. Wouldn't that be cool? :cool:
 

77bronco_ed

Bronco Guru
Joined
Jul 3, 2004
Messages
1,793
Next summer... ha ha ha I wish. If I can get mine driveable by the summer I would be happy to trailer it half way across the US to meet up.
 
Top