• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

New axles - hub install issue

xcntrk

Bronco Guru
Joined
Jan 12, 2012
Messages
2,473
Loc.
NOVA
Hi all, looking for assistance. I'm in the process of swapping out a freshly built D44 for my old Dana-30. From the 30 I'm carrying over everything from the spindle on out including; GM disc brake conversion, rotor, hub, bearings, lockout, etc.

The problem I'm having is with the lockout. I'm using Warn premium lock out hubs. My old D30 had a bolt and washer that installed right into the end of stub shaft and essentially holds the entire locking hub in place. My new D44 cromo stub shafts have no hole for this bolt.

The Warn hubs also have 2 snap rings, one small one on the end of the axle, and one large one that locks into the outer hub. Do I simply omit this locking bolt with the D44 setup and rely on the 2 snap rings to hold the lockout onto the hub? Or do I need a different lockout hub kit for this D44 axle?

?:??:??:?
 
OP
OP
xcntrk

xcntrk

Bronco Guru
Joined
Jan 12, 2012
Messages
2,473
Loc.
NOVA
Here's some pics.

This is the Dana-30 stub shaft with bolt at the end.

01D550C0-3296-459C-853A-CC560854EFDB-2408-000004483122DE2F.jpg







Here are the Dana-44 aftermarket cromo stub shafts with small hole but not threaded nor large enough for the bolt.

C1E69637-C738-4DD0-8203-6104DFFC93C4-2408-000004483A9B8172.jpg
 

fmcpeters

Full Member
Joined
Feb 8, 2008
Messages
188
If you can get the small snap ring in place that is all that is needed to omit the bolt on the end. Then install the large snapring. Some people use the original ford hubs for the GM brake conversion. The only issue with this is the snap ring will not go in place with the ford hub, so you install the bolt and washer and omit the snap ring.
 
OP
OP
xcntrk

xcntrk

Bronco Guru
Joined
Jan 12, 2012
Messages
2,473
Loc.
NOVA
I was incorrect about that small snap ring, it actually installs onto the warn hub portion which rides on the axle. At this point without that bolt, the only thing that holds the lockout internals in the hub is the large snap ring.
 

garberz

Bronco Influencer
Joined
Jun 24, 2007
Messages
6,864
Loc.
Conejo Valley, Ca.
With the chevy disk set up, you usually can't use the small snap-ring on the stub axle, just as your pic shows. You got it right.
 
OP
OP
xcntrk

xcntrk

Bronco Guru
Joined
Jan 12, 2012
Messages
2,473
Loc.
NOVA
^ so it's just the large snap ring that holds the locking hub in place?
 

TN1776

Bronco Guru
Joined
Oct 24, 2006
Messages
2,632
There are longer outers made that work with the GM conversion... I have the small snap ring on one side of my front 44 and the other side is just like your picture. All are aftermarket shafts but in PO fashion they don't all match.
 

bad 68

Sr. Member
Joined
Jul 1, 2010
Messages
930
Loc.
Northest Washington
so, if no snap ring or bolt in the end of the shaft, what keeps it from walking out of the hub and letting water and crap get in behind the spindle seal??
 

Jdgephar

Bronco Guru
Joined
Sep 25, 2012
Messages
1,526
When I put mine on, I had to push on the backside of the stub shaft and make sure it was all the way in. That got me about 1/4" that let me put the small snap ring in. Is that common that you make sure the stub is all the way into the spindle?
 

stlo

Bronco Guru
Joined
Mar 1, 2011
Messages
1,228
Loc.
tulsa
i put in the after market chrom-moly as well and couldnt get the snap ring on either...ive wheeled the piss out of mine the last two yrs with no prob
 
OP
OP
xcntrk

xcntrk

Bronco Guru
Joined
Jan 12, 2012
Messages
2,473
Loc.
NOVA
so, if no snap ring or bolt in the end of the shaft, what keeps it from walking out of the hub and letting water and crap get in behind the spindle seal??
There's a large snap ring that locks the internals into the hub. That's essentially all that is holding the hub in place. There's still a seal on the cap that keeps water from getting in there.
 
Top