• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

New Clutch having issues.....

stoker

Jr. Member
Joined
Aug 28, 2011
Messages
127
I’m running a 351W coupled to a 4-speed top-loader. Over the winter months I pulled the engine and installed a new rear main seal and new LUK clutch. I’ve only put a couple of hundred miles on it so far this summer. The new clutch was engaging at the bottom of the pedal travel (near the floor) but performing fine. Yesterday, on my way home, I felt the pedal “give” slightly and the clutch would not fully disengage with the pedal hard to the floor. I also had increased free play at the top of pedal travel. I figured it was a linkage issue but could find nothing amiss. I adjusted the pushrod to restore the correct free play in the pedal and everything seemed fine at first but soon went back to not fully disengaging after a few shifts. I can’t figure this one out but it looks like I’ll be pulling the engine again to check the clutch. I’m leaning towards a faulty clutch……..

Anybody have similar issues in the past?

Incidentally, the new rear main seal (1-piece, Fel-Pro 2921) still seems to drip oil but I can’t see this causeing the clutch issue.
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
Did you replace an old "Borg & Beck" (three fingered) style with a diaphragm style?
The diaphragm style takes more travel to fully engage and disengage. I had to raise the rubber upper bump stop to accommodate that travel.

Also, if you felt something "give" you might want to check the firewall where the pedal mechanism mounts. I've seen cowl rust that cause that problem.
 
Last edited by a moderator:
OP
OP
stoker

stoker

Jr. Member
Joined
Aug 28, 2011
Messages
127
Yes, The new clutch is a diaphragm style. Seemed fine for the first couple of hundered miles though.
I'm pretty sure the rubber bump stop is all the way up already. The clutch pedal sits considerably higher than the brake pedal.
I'll check the pedal mounting arrangement tonight. Thanks.
 

SHX669

Bronco Guru
Joined
Jan 9, 2009
Messages
1,997
Yes what blubuckaroo said - I had to " mess with " mine a couple of times to get enough travel .
On your rear main seal - did you use sealant on the flywheel to crank shaft bolts ? they can leak there if you didn't
 

pcf_mark

Bronco Guru
Joined
Jun 11, 2010
Messages
3,697
The clutch pedal is always higher than the brake - the travel is considerably more. Engine off try to turn the driveshaft when someone pushes the clutch in while in gear. If you can't it is not adjusted right yet. Then it is adjusting the free play to get a clean release with it running / high rpm.

When something "gives" I would get concerned. Maybe take the start off and take a peak in to see if the fork or diaphragm springs gave up?
 
OP
OP
stoker

stoker

Jr. Member
Joined
Aug 28, 2011
Messages
127
I raised the rubber pedal stop all the way which gave me a bit more travel in the pedal. Adjusted the linkage and all seems okay now. I'll give it a run tomorrow and hope it stays as it is. Strange how it was good and then needed further adjustment. I've not seen that happen before.

SSH669, I didn't use sealant on those bolts. Considered it but found them to be blind holes.
Thanks for the replies.
 

WILDHORSES

Sponsor/Vendor
Bronco Guru
Joined
Nov 7, 2003
Messages
2,253
Loc.
USA
A couple of more random yet pretty common issues. I don't know what year Bronco you are dealing with but the early years had a pretty weak equalizer bar they are known to crack and may not fall apart right away. Have someone press the clutch pedal while you are looking at the bracket.

The other thing is that clutch fork pivot attached to the inside of the bell housing. They can come loose. It would be hard to see that issue but you may be able to pull the boot and look inside while pressing the clutch.

I've installed many Luk and Centerforce clutches but have not had them act like what you describe. That leads me to believe it's a related part. I would not take the whole thing apart without checking these items.

Good luck

Jim
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
A couple of more random yet pretty common issues. I don't know what year Bronco you are dealing with but the early years had a pretty weak equalizer bar they are known to crack and may not fall apart right away. Have someone press the clutch pedal while you are looking at the bracket.

The other thing is that clutch fork pivot attached to the inside of the bell housing. They can come loose. It would be hard to see that issue but you may be able to pull the boot and look inside while pressing the clutch.

I've installed many Luk and Centerforce clutches but have not had them act like what you describe. That leads me to believe it's a related part. I would not take the whole thing apart without checking these items.

Good luck

Jim

Good point WH, about the loose fork pivot.
From the factory they are riveted to the bell housing. Those rivets can loosen up and cause issues. I haven't had it happen to me, but I've read about it here on CB.
Here's a repair kit for that issue.
https://www.tomsbroncoparts.com/product/tab-style-clutch-fork-pivot
 
Top