• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

New owner from Germany

OP
OP
T

tody

Full Member
Joined
Mar 22, 2017
Messages
207
borgeson swap well underway.

started with turning down the steering shaft back to it original size on a lathe, the old coupler was welded on.
c1a5786d-deb7-46c4-b9d9-b24200267be5.jpeg


milled to a DD shape.
83f77a29-a41d-4a6b-8f9d-9a7f9ee0afe7.jpeg


drilled small notches for the set screws:
ed221e0c-743a-4238-a4bc-e7ecf85d17f3.jpeg


and the upper coupler is on!
be11688a-7bfa-4478-aba0-6f5b47c4ed9e.jpeg


more to come tomorrow.
 
OP
OP
T

tody

Full Member
Joined
Mar 22, 2017
Messages
207
borgeson is in. all set screws put in with red loctite, i'll let that cure until tomorrow.
will then pull the bronco out of the shop, the mustang will be back in. still can't get that damn autolite 1100 to work properly. waiting for the right size reamer to arrive to put in throttle shaft bushings.

IMG_3795.jpeg

IMG_3796.jpeg

IMG_3797.jpeg
 
OP
OP
T

tody

Full Member
Joined
Mar 22, 2017
Messages
207
drove it today. day and night difference. steering is much more precise now, a lot less stressful to drive.
still does not fully return to center, though. so this means 7° bushings...
and i need to pull the steering wheel again, it's one or two teeth off.
 
OP
OP
T

tody

Full Member
Joined
Mar 22, 2017
Messages
207
steering wheel is now in correctly.

picked up a parcel from the post office today - twin stick shifters from jbfab.
they'll go in nicely with my nv3550 swap.

a buddy of mine ordered a big stash parts from summit, they also carry the full advance adapters kit. some parts are on backorder, so i'll have to wait until everything arrives.

but even with a three speed - it's a blast to drive with the new steering!
 
OP
OP
T

tody

Full Member
Joined
Mar 22, 2017
Messages
207
it's been a while since I updated this thread.
sort of fixed my noisy hardtop. one of the bows had separated from the roof. a friend provided me with 2k body glue. even though it looks like chewing gum in the picture, it seems to be holding up rather well.
still rattling like crazy in the rear of the hardtop. i think this is the locking mechanism, as the liftgate is not sitting very square in the opening. i'll address this later...
IMG_4033.jpeg


also, another bronco showed up close to me. i had seen the ad when it was for sale, and now it's half an hour away from me:
IMG_4027.jpeg


still some work to do on that rig.
no parking brake, on what seems to be a dana rearend.
shady wiring, that needs to be completely revised.
but has what seems to be a rather healthy 302 with a c4. also p/s with a hydroboost unit.
it was imported all the way from ecuador...
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Shady wiring seems to be a calling card for previous Bronco owners! Everyone becomes a wiring "expert" when they try to fix Broncos. Then the next owners become actual wiring experts trying to fix the fixes!

The rattling rear liftgate and tailgate are hallmarks of Broncos and something many of us have worked hard to get rid of.
There are several adjustments that really do help, but also things you can do to tweak them a bit.

One trick I've used (stole the idea from a Ford worker Bronco owner back in about 1980) is to fabricate two angle brackets to mount to the side pillars of the rear opening, then add two more rubber bumpstops to the brackets to apply more outward/rearward pressure on the liftgate.
Of course check all the usual things first, like loose or worn hinges, misadjusted latches, or missing rear stake pocket reinforcements.
But adding some additional pressure points does help.

For the tailgate, it's also about adjustments, but can also be about additional tension points.
If you don't have good tight weatherstripping pressed up tight against the gates, you're fighting an uphill battle. So starting there would make sense.
The main tailgate hinges/pivot points are available with polyurethane cushions instead of the hard metal-to-metal contact of the stock ones.
The 2-piece pivoting supports tend to rattle inside their pockets even if the rubber tensioners are in good shape. Adding some cushioning to the area can stop the rattling, or you can replace them with cables like modern tailgates have to get rid of 90% of the noise.

You may already have seen and tried some of those tricks, but that's just a starter list for fighting rattles in the back of Broncos. Lots of little things to do.

Good luck!

Paul
 

sprdv1

Contributor
REBEL
Joined
Mar 8, 2007
Messages
81,996
Keep plugging brother

it's been a while since I updated this thread.
sort of fixed my noisy hardtop. one of the bows had separated from the roof. a friend provided me with 2k body glue. even though it looks like chewing gum in the picture, it seems to be holding up rather well.
still rattling like crazy in the rear of the hardtop. i think this is the locking mechanism, as the liftgate is not sitting very square in the opening. i'll address this later...
IMG_4033.jpeg


also, another bronco showed up close to me. i had seen the ad when it was for sale, and now it's half an hour away from me:
IMG_4027.jpeg


still some work to do on that rig.
no parking brake, on what seems to be a dana rearend.
shady wiring, that needs to be completely revised.
but has what seems to be a rather healthy 302 with a c4. also p/s with a hydroboost unit.
it was imported all the way from ecuador...
 
OP
OP
T

tody

Full Member
Joined
Mar 22, 2017
Messages
207
Thanks Paul, as always your insights are highly appreciated!
 
OP
OP
T

tody

Full Member
Joined
Mar 22, 2017
Messages
207
A quick update after having driven it through pretty heavy rain today:
No real leaks anymore. One small dribble through the top hole in the driver side kick panel - the wiring harness clip going in there is missing.

Also, another electrical problem fixed.
The small harness going from the instrument voltage regulator was not putting through current very reliably. Put it in a sand blasting cabinet, cleaned up all the connectors. Gauges are now working as they should.

The glued hardtop bow is holding up. Next, tackle the squeaky rattle in the rear, somewhere on the liftgate. Found an eBay listing for some liftgate struts over here in Germany, will probably jump on it and try this out.

Winter project: NV3550 swap...
 

sprdv1

Contributor
REBEL
Joined
Mar 8, 2007
Messages
81,996
Nice to hear.. Time to push the heat, hit the cold weather projects..

Be ready to drive and enjoy it once it starts warming up again

Good luck sir
 
OP
OP
T

tody

Full Member
Joined
Mar 22, 2017
Messages
207
well, the electrical gremlins came back.
short drive today, no gauge working.
checked the wiring diagram. there is a lead going from the ignition switch to both the instrument voltage regulator and the turn signal fuse. turn signals had some issues in the past, too. thought it was corroded contacts in the fuse box, but maybe both problems are connected.
will check the back terminal of the ignition switch, and may just put in a new one to see if it helps anything!
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
The Black w/green wire on the center post of the ignition switch handles literally every accessory on the vehicle. So if the rest of them work fine (heater, radio, wipers and backup lamps basically), then the connector is good. If it can handle the load of the heater blower motor it should be able to work all the other accessories.
Still, can't hurt to try a new switch if you have one.

Would not hurt to revisit the fuse panel either though. Check it's backside to see if rust has built up or any of the connections are loose or failing.

Paul
 
OP
OP
T

tody

Full Member
Joined
Mar 22, 2017
Messages
207
The Black w/green wire on the center post of the ignition switch handles literally every accessory on the vehicle. So if the rest of them work fine (heater, radio, wipers and backup lamps basically), then the connector is good. If it can handle the load of the heater blower motor it should be able to work all the other accessories.
Still, can't hurt to try a new switch if you have one.

Would not hurt to revisit the fuse panel either though. Check it's backside to see if rust has built up or any of the connections are loose or failing.

Paul

not the answer i wanted to hear ;D
ok, next guess. maybe bad ground? perhaps i should run a seperate ground wire from the back of the cluster.
anyway, i'll dig out my electrical toolbox this afternoon and go through a couple of things!
 

sprdv1

Contributor
REBEL
Joined
Mar 8, 2007
Messages
81,996
You got it. Track it down one part, problem at a time
 
OP
OP
T

tody

Full Member
Joined
Mar 22, 2017
Messages
207
Bronco is in the shop again for the winter. NV3550 is well underway, this is the current state of affairs:

IMG_4136.jpeg


While I'm at it, I'll try to track down a few other things. This looks more like a leaky oil pan seal, and not the rear main, right?
IMG_4137.jpeg


When the oil pan is off, I'll also take off the front timing cover. I still suspect the knocking noise to come from the fuel pump eccentric or somewhere in this area...
 

Bitch'nBronco

Contributor
Loose Cannon
Joined
Dec 1, 2005
Messages
3,620
Loc.
Ringwood, NJ
Bronco is in the shop again for the winter. NV3550 is well underway, this is the current state of affairs:



IMG_4136.jpeg




While I'm at it, I'll try to track down a few other things. This looks more like a leaky oil pan seal, and not the rear main, right?

IMG_4137.jpeg




When the oil pan is off, I'll also take off the front timing cover. I still suspect the knocking noise to come from the fuel pump eccentric or somewhere in this area...
Yep, looks like an oil pan seal. If it was rear main it'd be leaking down from the bottom of the crank.

Sent from my SM-G981V using Tapatalk
 
OP
OP
T

tody

Full Member
Joined
Mar 22, 2017
Messages
207
more tearing apart, but also some reassembly.

first, the shaft for the transfer case:
IMG_4148.jpeg


also, the adapter plate to the transmission:
IMG_4149.jpeg

IMG_4150.jpeg

IMG_4151.jpeg


more to come on the swap in the next weeks.

a question remains - where does the tapping noise come from?
removed the front dress, and found that the outer ring of the fuel pump eccentric not only has play radially, but also axially.

here's a pic of the timing chain, marking on the cam sprocket reads 'S430 HD'. it has a raised portion which from my limited knowledge calls for a two piece?
can anyone school me on this, and whether it would also be possible to use the one piece eccentric, just to eliminate this as a cause for the knocking?
IMG_4142.jpeg
 
Top